kubota l3600

L3600, glide shift(I think) shift lever froze. Temps were in the low 20's, shifter just would not move. Forward and reverse were fine, I was just in 2nd gear, very slow. Running the tractor did not unfreeze it. Parked in the shop, turned the heat on, and it unfroze in about an hr, but as soon as...

Curious who has done that. And was it needed? My owner's manual for my L3600 says to adjust every 800 hours [have not done at 1000 hours]. Wonder if needed? And just FYI - that engine runs cool. My F3060 owner's manual does not mention valve adjustment- I have 2700 hours and have no idea if it...

Curious who has done that. My owner's manual for my L3600 says to adjust every 800 hours [have not done at 1000 hours]. Wonder if needed? That engine runs cool. My F3060 owner's manual does not mention valve adjustment- I have 2700 hours and have no idea if it was done before I bought it at...

Bought a L3600 with a Great Bend FEL/4in1 bucket, hydraulic top link and side link. Needed something a little bigger than my BX2230 for pulling/lifting logs(new sawmill) Probably paid too much(according to my wife-way too much) but I think it will work. The challenges- Bought it in Oct last...

Which grapple will fit a Kubota L3600HST tractor. Pushing small trees around.

I have a 2000 Kubota L3600. My heater and radio seem to be going in and out together. If I tap on the overhead cab sometimes it will come back on until I hit a bump and they will both turn off or cut out. I pulled the cab roof and started looking for problems. It appears that the power supply...

I've got an opportunity to get a 1996 Kubota L3600 with a box grader, bush hog and finish mower for $11,500. From the pics, it looks like it sits outside but seems to be in decent condition. I'll see it in person next week, but any thoughts about the price and or things to be leery of? Just...

I had just scooped up some dirt and was backing up. I heard a klunk and the steering quit altogether. I can turn the steering wheel freely but the wheels don't move. I couldn't find any hydraulic lines disconnected. All the other hydraulic functions work fine. Nothing at all is leaking that...

My gauge that comes with a can is reading in the yellow and red I think I have to much in it

tractor will steer Backwards but not forward, pulls hard to the left in forward belts are on, ties rods look good ..... ? cannot find the PS fluid reservoir though, not shown in manual update I found that it uses the same hydraulic fluid as the rest of the systems (loader and 3ph working) and...

Hello, I'm hoping somebody can steer me in the right direction. hahahee <whew> :o I fired my L2900 GST up and took it about 10 feet when I realized I had no steering to the right. I still had steering to the left. Here are the specific symptoms: turn to the right = massive leak and no wheel...

I have a leaking cylinder on my la680 and went to get the rebuild kit, but there are two different kits. I can not see markings to tell me what cylinder I have so is there any way to tell without opening the cylinder up to look at the "ram" size?

A few days ago mid Michigan was slammed with 18-22" of snow. I was trying to clear out the driveway of the house we just bought because I had a delivery coming. It was wet and slippery under all that snow. When I went to back up to reposition my little snow plow rig (a 99 Durango) and I couldn't...

I've never owned a grain drill Is there one that would work on ground that was already worked up or unworked ground, and which can I handle with a 36 hp Kubota l3600 4wd tractor?

Guy traded it in on a new tractor at a John Deere dealer, they thought it was stuck in 4x4 but it wasn't LOL!! Long story short I got a deal, a really good deal! It even came with a back blade and they delivered it! It's 38hp and has a nifty glide shift trans. I dig it! Kids like it too and...

Looking at this tractor, may purchase it but need some advice. It's for sale at a John Deere dealer. 1200 hours, R4 tires, loader and back blade, priced at $9995. Dealer says that the previous owner only used it to move dirt and never took it out of 4x4. They say the just want to move it and not...

>First a little background- Within the last few months I've done a few things to my Kubota... 1. The FEL had always felt a little weak. I bought a gauge and checked the pressure at 2200 psi which was lower than the factory psi of 2498psi. I added 1 #10 SS washer which brought it up to...

I have a L3600 with a fuel tank that is leaking. It is not a hose but is coming from the bottom of the tank. It looks difficult to pull out the tank but that is what needs to be done. Doe anyone have a shop manual or experience in doing this. Buddy

Withdrawn

took my tractor all apart to fix a leak on gear cover. removed the speed control plate and govenor springs. 2 springs. not sure how springs were conected now. have the repair book but pics in book are poor black and white. not sure if springs were like a chevy carb springs one inside the other...

its ben a few years since i broke anything so im back. broke my stering moving snow this winter. hydraulic rod broke off at the thread part that screws into . weled it back together. should be ok. have hole in front engine cover as results of stering breaking hiting.dont think i want to replace...

Hi Guys, I primarily use my tractor for moving snow. I noticed my last time out that my FEL "up/down" controls are not working properly. For example, when I pull the lever all the way down to raise the FEL, it moves super, super slow. If I just barely push down on the lever, the FEL actually...

looking for advise put in the updated seal kit and spacer on a L3600 gst and now its leaking again!:mad: anybody had this happen ? just getting ready to tear it.serial no 51994 please help looking for any suggestions thanks in advance!

Long time lurker, first time posting! I have a L 3130 Kubota with front end loader and have been jonesin' for a back hoe attachment. Seems like the consensus here is to avoid a straight three point hitch attachment. I have found a Woods model 7500 for sale that has a frame attachment and PTO...

I am looking at driving a motor for a sickle bar that is rated at 4 gpm from my L3600. Rated flow for the tractor is 8 GPM. I have a Kubota loader and 1 factory valve in the back for 3 pt. tilt. Basically have two questions: How do I tap into the hydraulics to run the valves for lift...

Trying to remove the tie rod ends on a Kubota L3600, when I try and back the nut off holding tie rod end the nut and bolt are turning, am I overlooking something or is there a trick to removing the tie rod end,

Not sure it this should go under Kubota or Lawn care but anyway... I have about 3 acres of lawn near the house. Have mowed it with a 42" craftsman for quite a few years. Wife does much of it. Also have a back field of about the same size that I just brush hog a time or two a year and mow a...

I just acquired a used FEL but the hydraulic stop at the quick disconnects ( the tractor ends stayed with the PO). So I need to order 3 hoses with disconnects. What thread to I need to connect to the Kubota? (under the right side operator platform). I also want to add 2 hyd circuits to the...

Just brought home my new (used) L3600 GST 4wd. and now need to buy a FEL. Replacing a L2850 with Kubota BF500 FEL. Both L2850 and FEL were a little small for my needs. Got a couple prices for a new FEL to fit the L3600 but they are more than what I paid for the tractor. Found an Ansung 2540C...

My preheat function no longer works on my L3600. I don't know where to find or repair.....any suggestions?

i have a L3600 4x4 and was going down my dirt road and wanted to take it out of 4x4 so i stopped and did so. the front part of the front axle has a carrier bearing looking thing that lines up with the front drive shaft that i noticed was loose due to the bolts broke out of it so i replaced and...

I need a copy of owners manual and also a copy of a repair manual for a Kubota L3600 4x4. Please reply to TractorByNet or Best1953@Live.com Thanks

What's a fair price on an L3600 ? I currently reside on a 1/2 acre and care for it with a push mower. Just purchased a 106acre place, 15 acres of fields and the rest hilly mountain terrain. I don't think the push mower will cut it :). I have been listening to all of your advice to other members...

I'm a newbie so these might be naive questions. I have about 40 acres that I would like to hay and cut alfalfa for horses. I have a Kubota L3600 tractor. The spec sheet says it produces 38 hp with about 31 hp at the pto. Locally there is a JD 820 mower conditioner available. The spec on this...

I am looking for a loader bucket for my L3600 tractor. The loader is a model LA680. The bucket is about 72" wide. I do not have the quick attach system.

Hello everyone. I hope someone can help me here. I just bought a L3600 with the GST tranny, my question is this: Forward , neutral, reverse on the column shift. On my left while in the seat are my high and low gears 1-8. This also has a neutral.If the left shifter(high low gears) is in neutral...

Can someone tell me the oil capacity of a Kubota L3600 4 cylinder diesel. Misplaced the manual and wanted to have everything ready prior to changing. Thanks

My brother lives in Montana.......nearest Kubota dealer hours away.......He has an L3600 GST which he got this summer. Time to change all the oil and filters. Would NAPA carry filters or is there a Kubota dealer near Boseman that could ship the stuff he needs. Is there a substitute for Super UDT oil

We are buying a 97 L3600 GST with full cab, loader, R4 tires. Does anyone know rough what the weight of this setup is? I am just trying to figure out if I need to keep my 25' gooseneck (GVW of 14000, but can haul 11500) to haul the tractor or if my 14' equipment trailer is good enough (GVW of...

We are looking at buying a L3600GST that has a LA680 loader mounted on it, but I can't seem to find the lift capacity of the LA680. Does anyone know what the lift cap of this loader is?

I'M KNEW TO THIS FORUM (AND TRACTORS IN GENERAL). MY DAD JUST PURCHASED A USED L3600. THE PIGTAIL LOOKING(MAYBE GLOWPLUG) WARNING LIGHT HAS COME ON TWICE, BUT GOES OUT AFTER A MINUTE OR SO. WHAT SHOULD WE LOOK FOR. THANKS IN ADVANCE!!

I put this in a kubota forum not much in the way of resposes. I was looking at my tractor last night and noticed a small hydro leak at the right (looking at the rear of the tractor from behind) rear axle housing where the frame meets the axle. The fluid is coming from underneath the 6 bolts...

I did the cross reference for the wix air filters and found them to be to long and closed on one end (also checked with dealer and he said his is closed on one end). Mine has a threaded wing nut that is used to secure the filter housing lid to the filter housing so the wing nut must go through...

Anyone know how I can get the part number for the fan belt on an L3600gst 1998. Thanks.

I was looking at my tractor last night and noticed a small hydro leak at the right (looking at the rear of the tractor from behind) rear axle housing where the frame meets the axle. The fluid is coming from underneath the 6 bolts that hold the axle to the frame. Anyone know if this is something...

I'll be getting a late 90's l3600 gst on Monday. I was wondering why there are so few posts on this tractor? The only 2 things I see wrong with it are glow plug light stays on and a leak at the hose fitting where the tractor hydraulics connects to the backhoe hydraulics. I did read some about an...

I took my tractor apart to fix the clutch last yr . degreesed everthing with engine cleaner. rmp guage now dosnt work rite. at idle needle pegs out and i think the hr guage spins around quicker . any one ben here with this problem. thanks b.

I am looking to freshen up the L3600 and need the grill pieces, and side tin, but the dealer is just out of this world price wise. where can i find used or reasonable new panels and grill? or is dealer only option?

I just picked up a wood splitter with no motor or valve. Limited experience with hydraulics. I will only use it 10 - 20 hours a year so want to hook it to the the L3600. I understand it will be a bit slow but hopefully not TOO bad. I see most of the existing stuff (loader, etc) uses 3/8 hoses...

Sorry, got this in wrong area somehow. This can be removed...

Ijust finished puting my tractor back together after fixing the rusty clutch linkage. started it up and no power stering. tried switching the hoses left and right. thought maybe i had them mixed up. still no stering. think the pumps not working.I think the repair manuel said these things are...

Just used my Kubota L3600 tractor tilling yesterday, went to park it and noticed a loud noise. When I put it in 2 wheel the noise goes away. Any suggestions as to problem. If so is this something a mechanically minded person can repair if I buy a manual. Or would it be something better left to...

Had my tractor out in the morning and started it several times. No problem. Went to start it later and just got a very brief noise. Sounded sort of like a bad connection arcing. Now nothing on the instrument panel - no lights, no clicking, nothing. Checked shift levers, etc but I don't...

I just bought a new M9540. Now I need to know about how much my L3600 is worth. It is a 1997 model with Glide Shift Transmission, FEL, 4WD, and 600 hours. Purchaced new was $21000. If is in excellent shape and has always been kept inside. I have no idea how much to ask. I welcome your input.

Just replaced the GTS clutch pack and the 3 point does not work, also the PTO stayes in gauged all the time this is a non independent PTO set up. All the hydraulic lines are hard lines and can not b crossed only fit one way. I spec i can figger how the PTO got out of whack and will look into it...

It tries to move but will not. customer called me a few days ago and said it would move but takes awhile and he thought the steering also was a little hard at that time. I went to haul it back to the shop and it will slowly move a foot or so and that's it like a worn out clutch. it does not seam...

Update on engine, Guess the title thread was wrong only 2 responces and thanks for these.On other post. And with the Kubota out of favor for the past 5 weeks have had to rent another tractor and end of year added expenses of tractor it cost me for a 5 year adverage 50 + a month not counting the...

I am looking at purchasing an L3600 here in the N. Texas area and was wondering if this is a good price. It has an LA680 front loader, 622 hours, ag tires, shuttle shift, a 6' bush hog finish mower, a 6' bush hog shredder, and a 6' disk. All of this for $16k. The tractor is in immaculate...

L3600 Engine won\'t shut off I have a '97 Kubota L3600 that will not shut off when I turn the key to the off position. The kill knob can be pulled out right next to the key which shuts off the air to the engine, taht works just fine. Any idea where I can start to trouble shoot the problem...

I am looking at the specs for L3600 - especially in the Hydraulic section. It has Pump Capacity (main) and Pump Capacity (PS). Does anybody know what this means? What does PS stand for and why are two pump capacities listed for L2800, L3400 and L4400 models? All the other models have one...

I looked all over the tractor and I'm having trouble finding the fill tube or plug for the hydrualic / transmission. How do I determine if the oil level is low if it only has a plug. Baught it used and don't have a manual (yet).

owning-ML-813984-ML- Kubota specific post.

This evening after dark parked tractor in shed turned off lights,stepping on brake noticed no parking light,turned off ignition switch engine continue to run,and now no lights,pulled Emer.Stop sw.diesel engine quit but now will not start,Tractor serviced about 10 hour ago at this time battery...

Before having to get new computer had parts list on hard drive, and in the transfer of data lost the parts list,how do I again get a down load parts listing for a L3600 GST ? It is 40 miles to closest dealer and helps to phone in the parts needed. Today the right front axle came off the tractor...

My husband asked me to find some info for him about his tractor...The hydraulics are not working. He has changed the filter and fluid but still no go. They told him to clean the screen at the dealership but the owner's manual doesn't show where it is located. I have read on this site that some...

I have been reading TBN for about a year trying to educate myself on what to look for in a tractor and if the asking price is a good one or not. I think I found a good one but I am unable to pull the trigger without some profound advise from the TBN members. What I have found is an L3600 with...

Anybody have any experience with a Kubota L3600? I have a need to bushog, rake, front end load, etc. and I found a late model L3600 which seems to be pretty heavy duty. the price was 14,500 with FEL, could get him down a bit lower I think (43 hours). It looked like a good machine-- ? any...

I have a L-3600 Kobuta with 1200 Hrs and when had app.700 hours broke the drive shaft to front end drive, replaced then again at 1200 hours again the drive shaft pin on the coupling to front drive gave away and the spline was damaged to point of needing to be replaced, after the new shaft was...

I purchased a 1997 Kubota L3600 that was apparently left out in the weather and some of the sheet metal is rusted out. I am looking for the metal section located behind the driver seat that incorporates the small tool box. Can anyone give me some input on locating used parts such as this? Any...

Trying to find a place to buy used Kubota sheet metal parts. I have a 1997 Kubota L3600 that needs the section behind the driver seat that has the small tool box built in. Haven't had any luck on the Internet locating this part (new or used). The part number is TA040-4719-0.

If anybody in the New England area is in the market for a Kubota L3600 w/ FEL, there is one for sale here in Moultonborough, NH. It is listed as a 1998 GST with 187 hours (I checked the meter) It has turf tires (big meaty rear tires). Price is listed at $18,000 Tractor appears to be in nice...

My neighbor has a L3600 not HST and that's about all I can tell you about it. He thinks the hydraulic fluid is low, but the dipstick isn't where mine is on my B2410. We didn't look under the hood. but can someone point me to it's location? Or do you just fill it until you see the fluid in the...

I'm about ready to buy a new B7800 but came across the above for $20,000 firm, about 15 miles from where I live. I'd love any opinions on a comparison of these units. New with backhoe, regular bucket backhoe and rear mower, my local price for the B7800 is $25,000. I'm on 8 acres, somewhat...

Need some advice on a steering cylinder problem I was using the L3600 to fill in where a log skidder had pulled logs from the woods and making a road way again. The cap end to the steering cylinder seperated from the body and dumped the oil pulled the tractor into the shop with 2nd tractor and...

Kobuta Mechanics could you answer this Question, yesterday Brush-hogging in 4 Whl. drive noticed front end wasn't pulling (Rear whls. slipping) while cutting uphill on a pond bank. No noise or reason to think there was a problem other than this. This morning blocked rear whl. took jack lifted...

HELP! I AM BUYING A USED L3600 AND I WOULD LIKE TO PUT A BACKHOE ON IT BUT I'M NOT QUITE SURE OF WHICH UNIT TO BUY. I WILL BE DOING SOME STUMPING (8-10" STUMPS) SOME DIGING IN STUBORN ROCKY SOIL. MY LOT IS NOT WHAT I WOULD CALL HARD PAN SOIL, BUT IT IS REAL TOUGH STUFF, TO PLANT A BUSH W/ A...

I BOUGHT THE TRACTOR USED W/1100 HRS. IT'S A 96 MODEL. SO FAR I HAVE HAD TO REPLACE THE FRONT AXLE TUBE DUE TO EXCESS WEAR ON PIVOT, ALONG WITH THE RING AND PINION. THEN THE CLUTCH. THE SEAL IN THE FRONT DRIVE SHAFT PUKED DURING SNOW SEASON.NOW THE SEALS IN THE OUTER AXLES ARE LEAKING. SO IS...

Anybody have an idea what an L-3600 GST with cab and front mounted snow blower would be worth? Unit has 63 hours on it. No other implements with unit.