mount

  1. hayden

    Be careful where you mount hydraulic lines...

    I recently installed permanant hydraulic hoses from the rear to front of my tractor for a hydraulic snow blower and PTO power pack. The power pack is 3PH mounted with a pump on the PTO, and its hoses plug into the rear end of my permanent hoses. The snow blower is mounted to the loader in...
    • hayden
    • Thread
    • Views: 242
    • auto-moderated hydraulic mount
    • Replies: 0
    • Forum: Hydraulics
  2. Sodo

    Belly mower vs 3-point finish mower

    It seems MUCH easier (and cheaper) to attach a 3-point finish mower than a belly mower. These 3-point hitch (finish) mowers roll on four casters, same as many of the belly mowers. 3-point mower. Here's a pic from Titan Attachments website. Price: $1617.00 3-point hitch mower R&R is...
  3. W

    BX-24 snowblower front mount

    I have a bx-2750c snowblower and have a question about operation. It has a hydraulic chute turner. With the snowblower in any position I can turn it counter clockwise ( with the blower raised ) To turn it clockwise the blower has to be on the ground with the stick forward in the float position...
  4. M

    Front mount or loader mount blower?

    What's the preference here. I'll have a power pack for hydraulics for a firewood processor so I can go either way.
  5. nikdfish

    Magnetic mount lightbar for the Z930M

    I just finished up doing warning flashers for the Z930M & figured I might as well do a lightbar. Unlike the flashers, the 120 watt lightbar will be run from a relay & a seperate, fused, battery connection. The switch controlling the relay will be supplied from the same key switched power...
  6. DennisfromCincy

    Relieving stress from top link tractor mount - 3 Pt backhoe

    In a "Hydraulics" thread another member brought up the possibility of damaging the tractor top link mount because of stresses of a 3-point backhoe on a compact tractor. I do not dispute that possibility. I do rest most of the backhoe weight on the drawbar of my EX2900 which relieves some...
  7. R

    Grasshopper 925 Front Mount Grease Fitting

    Any good way to grease the front driveshaft pillow block zerk without removing the mower deck?
  8. D

    Anybody mount Ratchet Rake to forks?

    I need to work near my vinyl fence and am thinking I would have increased visibility of the ratchet rake if I mount them to my forks instead of my bucket. Has anybody tried this?
  9. newbury

    How do you mount your fuel transfer tanks?

    Background - Bought 2 50 gal transfer tanks years about 2013 for $100 total . Intent was to fill with diesel and keep at site in Mississippi. Got them filled in Mississippi, rarely use them. So I'm wanting to "mount" 1 in the bed of my F350 and also perhaps a near future F250/Ram (yet to be...
  10. S

    Mid mount or 3PH mower?

    So, I'm looking at a 25 hp, cab tractor for the lawn and light snow removal. Looking for pros and cons of a belly mower vs a 3 ph. I see the belly mower being more maneuverable but more of a pain to take on and off. I expect the mower to be on and the loader to be off in the summer, then mower...
  11. P

    Kioti KM2560 Mid-Mower J-Latch

    One of the J-Latch (Kioti PN 066073) for my KM2560 Mid-Mount belly deck is missing, have no idea what happened to it. These are the J shaped, spring loaded clevis pins (approx 1/2" OD) that connect the deck front attachment arms to the frame. Page 45 of the manual. I cannot find these available...
  12. M

    How to mount a posthole digger

    I have a rather strange request. I need some ideas for how I can mount a posthole digger on my 3 point. Easy peasy normally. I have always had my digger dangling from a pulley in the rafters. But now I need to haul digger, mower, and tractor to a far-away remote location where there are no...
  13. C

    L434 FEL mount and dismount

    Not sure if this subject has any interest, but... I'm "practicing" removing and installing the FEL on a newly acquired (but not new) B2601 This loader has pins and the hydraulic connections are not modular. Following the directions in the product manual, along with tips shown in a generic...
  14. B

    Bent the loader mount on my 2515h

    Well I bent the loader mount on my 2515h enough that I couldn’t pull the left side pin to remove the loader. The dealer was able to get it bent back enough that I can remove the pin with some effort, or so he said. I don’t have it back to try it yet. I guess it got bent when I hit a buried rock...
  15. P

    Convert 70's tractor to quick attach plate, use original mount?

    The bucket is falling apart on my Ford 3600. I'd like to convert it to quick attach. Should I cut the mounts off my bucket and have those welded on or is there a mount piece I can buy for pins that can be welded on?

    16. Herd Seed Broadcaster model I-92 - hitch mount (electric powered)

    Virginia
    View Item »
  16. Seldomseen

    CHAIN SAW HOLDER?

    I have a JD 5220 and need ideas for mounting a chain saw and box for tools / chains. 🤷‍♂️ Anyone? Thanks, Bill
  17. 2

    Carrier for lopping shears?

    I see a bunch of suggestions for how to make a mount to carry a chainsaw, but does anyone have a good tip for carrying lopping shears like these compound shears from HF? Long Reach Ratcheting Bypass Lopper I keep seeing these short stubs of tree saplings in my field that the rotary cutter...
  18. C

    "New" Tiller Draw Pins Too Close Together

    While I'm not a total novice, I'm no tractor expert at all. My 33 HP TYM HST has held up well over the years, and I have no trouble swapping my brush hog, box blade, or rake on and off my 3 pt hitch. I bought a tiller (Shibaura RS 3147, also sold as Yanmar) for a song and a dance. I've...
    • caine
    • Thread
    • Views: 8789
    • cat 1 draw pin mount tiller
    • Replies: 44
    • Forum: Attachments

Footer Links 1

Top