remotes

Asking because I've never heard it asked & I bet it's pretty rare - I am considering removing my rear remotes from my ck10 (ck2610) for reasons; any advice on how to sell or price them? Tractor has ~200 hours, the remotes are in perfect condition & are not a low/intermittent use part anyway...

Purchased the kits last fall, but with winter, never got to the task of installation. First set is a straight directional control valve, the second set is a DCV with float. I think that combination will take care of any application I desire. A top link and height adjustment for the York rake...

I have a cx2510hst, I have the factory 3rd function on the loader control. I'm looking at getting the Norwood hydraulic capstan for the rear. My question, the factory CKA 101 rear remote kit, I'm assuming that can install fine with the 3rd function, since I would guess it would connect to...

I have a 2860e with a FEL. I would like to add rear remotes which it does not have. Any suggestions about the process and thoughts on the cost? Thank you!

I have a 2860e with a FEL. I would like to add rear remotes which it does not have. Any suggestions about the process and thoughts on the cost? Thank you!

I have a 1996 New Holland 4630 with 3 rear remotes. Currently they all detent into position. I want to remove the detent function so they are momentary only. I saw in the manual you can back off a set nut and adjust this, but it has no effect. I even completely removed the spring and it made no...

I have a 2022 Mahindra 2660 built by TYM with one rear remote and i would like to add another to have two remotes anyone have any idea where i could try to find the factory type remotes for a cab tractor. Wondering if maybe TYM might fit. I have tried on google nothing so far in stock.

Need to add rear remotes to my Kubota L3130. There is no loader or back hoe on the tractor, and likely never will be. The two pages of the Operator’s Manual that I have attached below say that I should be able to plug my hoses into the hydro block underneath the right footrest by simply...

Since there isn’t a lot of info floating around concerning adding rear remotes to a MT242HC I thought it a good idea to post this project in case others might be interested in doing the same. I’ll be adding a 6-circuit hydraulic multiplier offered by Summit Hydraulics. Starting out I’ll post a...

I’m a soon to be a new owner of a MT242HC and need info regarding rear remotes. I need a total of 4-rear remotes and expected that could be accomplished using a Summit Multiplier. The dealer is telling me that first a 2nd LS rear remote needs be installed before they can connect a Summit...

Having some issues with the remotes on my 4630 and want to see if i can get some insight before I tear things apart. I use one remote to run a FEL. It is basically turned on all the time. We never needed the other remote until we recently hooked up a round baler. When activating the second...

Can I use my remotes for a top link?

I am about to add rear remotes to my LX2610 - I already have a 3rd function and backhoe. I have it basically figured out (thanks to Dan/Thisoldhokie !) and found some information. The way the LX2610 is configured, PB off the loader valve goes to the third function, which then feeds the backhoe...

My NX4510 has 2 rear remotes. Neither has the float function. Can I run a backhoe from these remotes that don't have float function?

If I want to run a hydraulic motor off my rear remote valve/coupler, do I need more than just the two lines? In other words, do I also need a tank return, so when turn the rear remote valve/coupler off it doesn't just slam to a stop? If I do how is it plumbed?

I’m looking at adding rear remotes to my L3240 using a Summit Hydraulic remote kit to supply top and tilt cylinders. The summit kit includes a T connection to return to the tank. Is the T connection really necessary for top and tilt (2 way) cylinders? I have a W R Long 3rd function valve...

Just helped a friend buy a 2008 JD 3038e. Now we want to put 2 rear remote hydraulic connections on it. 1. How and where does this connect? 2. What do we need and how do we do it? Any suggestions appreciated.

I recently purchased an 850 with factory dual remotes. I'm a large person and the levers hit my leg. Additionally, both valve bodies are leaking. I want to delete the remotes completely. I only run a mower and have other machines with loader. I've found the replacement "cap" that has no ports...

I'm looking for another tractor to be a dedicated tedding or raking tractor. I need at least one remote but it has to have a 4 position valve with float mode. Back in the day I had a 3930 with dual pumps and dual remotes that had this feature. I am finding out that I should have kept that...

I'm unsure of where to tie in the hydraulic hoses for Fit Rite rear remotes on my M62. I've read the thread here originated by RedNeckGeek. His post is helpful, but I don't have factory install instructions, and most of RedNeckGeek's pictures of his install show his initial factory...

Hydraulic remotes in my M8200 have always worked fine. But, about 5 weeks ago, the right remote began "slowing down". It works, but goes very slow. So, if the lift function hose is attached to the right port - its lifts the disk very slowly. If I switch hoses then the lower down function...