4110 3pt hitch measurement needed, please

   / 4110 3pt hitch measurement needed, please #1  

2nstonge

Gold Member
Joined
Feb 16, 2004
Messages
369
Location
North Bennington, Vermont
Tractor
JD 4110 w/HST
I ordered a CCM tiller yesterday (& a landscape rake, too), so that the good folks at CCI can cut the PTO to the correct length & ship everything I need the measurement from the base/stub of the rear PTO drive to the midpoint of the centerline of the lower draft links mounting point - draft links must be level in the horizontal position & at a 26" spread.
I took delivery of the 4110 in December, the BH was attached & I'm just realizing the dealer didn't leave the 3pt hardware or the ballast box! I must've been too excited to notice. I've had no reason to remove the BH until now & I can't connect with the dealer until Saturday...any help would be great!

Thanks much, -Norm
 
   / 4110 3pt hitch measurement needed, please #2  
I measured my 4010 this afternoon. It should be the same as the 4110. It was 21 3/4" from the end of the PTO to the mid point of the drawbar between the lift arms with the drawbar near horizontal. The drawbar is 26" wide.

Ralph
 
   / 4110 3pt hitch measurement needed, please #4  
Hello,

Don' knowt if you still need some measurements, I took the following on my 4110.

From the end of the PTO shaft on the 4110 to the end of the lift arms I had 22.5"

I also measured the two PTO shaft I use:

Tiller (Bhuller Farm King 60") PTO shaft
Fully expanded = 32"
Fully retracted = 26"
Tiller side of the PTO shaft = 15.5" (attached to a slip clutch)
Tractor side of the PTO shaft = 20"

Snow Blower (Pronovost Puma 54") PTO shaft
When attached to the tractor = 33"
When fully retracted = 29.5"

I also took a few photos and will post them following this post!

Hypernix
 
   / 4110 3pt hitch measurement needed, please #5  
This picture shows the Tiller PTO shaft fully retracted.

Hypernix
 

Attachments

  • 608252-TillerPTOShaftRetracted.jpg
    608252-TillerPTOShaftRetracted.jpg
    76.5 KB · Views: 145
   / 4110 3pt hitch measurement needed, please #6  
This one shows the PTO Shaft extended...

Hypernix
 

Attachments

  • 608254-TillerPTOShaftExtended.jpg
    608254-TillerPTOShaftExtended.jpg
    78.5 KB · Views: 139
   / 4110 3pt hitch measurement needed, please #7  
This one shows the end of the PTO Shaft that connects to the tractor... It uses a sliding "bucle" Not sure if this is the exact term, but it seems to be more heavy duty than the pin used on the Snow Blower Shaft.

Hypernix
 

Attachments

  • 608256-TillerPTOShaftTractorEnd.jpg
    608256-TillerPTOShaftTractorEnd.jpg
    62.4 KB · Views: 126
   / 4110 3pt hitch measurement needed, please #8  
This one shows the tiller end of the PTO Shaft attached to a slip clutch...

Hypernix
 

Attachments

  • 608257-TillerPTOShaftTillerEnd.jpg
    608257-TillerPTOShaftTillerEnd.jpg
    45.4 KB · Views: 123
   / 4110 3pt hitch measurement needed, please #9  
This one shows the end of the PTO Shaft that connects to the tractor end and which I use with the Snow blower. Notice the pin used to lock the PTO Shaft...

Hypernix
 

Attachments

  • 608258-SnowBlowerPTOShaftTractorEnd.jpg
    608258-SnowBlowerPTOShaftTractorEnd.jpg
    48.2 KB · Views: 137
   / 4110 3pt hitch measurement needed, please #10  
And finally a picture of the PTO Shaft attached to the tractor and the snow blower.

Hypernix
 

Attachments

  • 608259-SnowBlowerPTOShaftAttached.jpg
    608259-SnowBlowerPTOShaftAttached.jpg
    74 KB · Views: 142

Tractor & Equipment Auctions

2019 Utility Trailer Manufacturing, 53' Trailer (A47371)
2019 Utility...
2017 Bobcat E32 Mini Excavator (A46683)
2017 Bobcat E32...
2025 Safety Basket Forklift Attachment (A46683)
2025 Safety Basket...
2014 JCB 260T Track Skid Steer (A49339)
2014 JCB 260T...
2020 PETERBILT 579 TANDEM AXLE SLEEPER (A45679)
2020 PETERBILT 579...
Barber 600HD Surf Rake (A46683)
Barber 600HD Surf...
 
Top