4115 60"deck MMM install help
- Thread starter hawk7
- Start date
- Views: 6596
Re: 4115 60\"deck MMM install help
I forgot to mention that I have the front bush gard installed so I dont need the 2 mounting plates to put on the front of the tractor. Also in this picture, part number 1 will slide into the back of the bush gard slot but then the front holes where the pin should slide threw doesnt line up. The holes are out front further. So if I have to correct part then mabey the bush guard is for a different tractor?? But it lines up with everthing when I installed it??
I forgot to mention that I have the front bush gard installed so I dont need the 2 mounting plates to put on the front of the tractor. Also in this picture, part number 1 will slide into the back of the bush gard slot but then the front holes where the pin should slide threw doesnt line up. The holes are out front further. So if I have to correct part then mabey the bush guard is for a different tractor?? But it lines up with everthing when I installed it??
Attachments
al3
Silver Member
Re: 4115 60\"deck MMM install help
Hi
Page 30 of the MM mower ops manual shows a picture of the attaching support bracket (your "part 1" above) mounted in position. If yours doesn't fit, sounds like one of two parts you have aren't correct.
Using the support bracket you have (part 1 again) post the distance from the center of the fixed pin to the center of the pin hole. I'll check mine tomorrow (a 4110)
Hi
Page 30 of the MM mower ops manual shows a picture of the attaching support bracket (your "part 1" above) mounted in position. If yours doesn't fit, sounds like one of two parts you have aren't correct.
Using the support bracket you have (part 1 again) post the distance from the center of the fixed pin to the center of the pin hole. I'll check mine tomorrow (a 4110)
Re: 4115 60\"deck MMM install help
OK
The hood guard has a mounting distance of 4-5/8 center of the hole that part 2 (pin slides threw) to the center of the bar of part 1 (piece that hangs in hood guard hook) in the attached picture. The mounting bracket that I got (part 1) center to center is 2-1/2 ". It fits from one side of the hood guard to the other. It just isnt long enough to get the holes to line up so part 2 will slide into place to lock it in. I know the hood guard is ok since I have a front hitch that mounts up to it fine and is 4-5/8 center to center. So my question is, If i order part 1 for the 4115 will it be the correct part or will it be the same thing I have?? I bought this deck used and it came off of a 4110 but is made for a 4110 and a 4115. The deere site shows the mounting kit to fit both tractors. If you dont have the hood guard you have to buy the 2 brackets to bolt onto the front of the tractor so you can slide part 1 into the brackets. Any help would be great.
OK
The hood guard has a mounting distance of 4-5/8 center of the hole that part 2 (pin slides threw) to the center of the bar of part 1 (piece that hangs in hood guard hook) in the attached picture. The mounting bracket that I got (part 1) center to center is 2-1/2 ". It fits from one side of the hood guard to the other. It just isnt long enough to get the holes to line up so part 2 will slide into place to lock it in. I know the hood guard is ok since I have a front hitch that mounts up to it fine and is 4-5/8 center to center. So my question is, If i order part 1 for the 4115 will it be the correct part or will it be the same thing I have?? I bought this deck used and it came off of a 4110 but is made for a 4110 and a 4115. The deere site shows the mounting kit to fit both tractors. If you dont have the hood guard you have to buy the 2 brackets to bolt onto the front of the tractor so you can slide part 1 into the brackets. Any help would be great.
Attachments
Re: 4115 60\"deck MMM install help
I also need to know if you use parts 11,12 and 15 in the picture I have attached. I see a place on the frame to bolt this up to towars the front of the tractor but it will only bolt up and not use the lock nut on the other side as the mounting holes are threaded. Any pictures of a MMM on a 4115 would be GREAT. Side shots,Back shots and front shots.
THanks again
I also need to know if you use parts 11,12 and 15 in the picture I have attached. I see a place on the frame to bolt this up to towars the front of the tractor but it will only bolt up and not use the lock nut on the other side as the mounting holes are threaded. Any pictures of a MMM on a 4115 would be GREAT. Side shots,Back shots and front shots.
THanks again
Attachments
acs55812
Silver Member
Re: 4115 60\"deck MMM install help
That seems to look like the mounting parts I have on my 4100--are the 4115 supposed to be the same?
That seems to look like the mounting parts I have on my 4100--are the 4115 supposed to be the same?
Re: 4115 60\"deck MMM install help
if you look it up under deere parts it says it is for both the 4110 and the 4115. Do you have yours mounted to a hood guard or the bracket? Also do you know what the center to center meassurement between the solid pin and the slide the pin of part 1?? Also does your use the LH and RH brackets. In the picture above it is numbers 11,12,16
if you look it up under deere parts it says it is for both the 4110 and the 4115. Do you have yours mounted to a hood guard or the bracket? Also do you know what the center to center meassurement between the solid pin and the slide the pin of part 1?? Also does your use the LH and RH brackets. In the picture above it is numbers 11,12,16
al3
Silver Member
Re: 4115 60\"deck MMM install help
I'm posting two pics. This one shows the mower mounting bracket mounted to the hood guard assembly. 4 &5/8s (notionally, +/- 1/8) is the measurement. Sounds like you have the incorrect mounting bracket (part1).
Second shot, next post, will show the the LH/RH brackets mounted on the tractor. You can see the detail of the RH bracket. Good luck---
I'm posting two pics. This one shows the mower mounting bracket mounted to the hood guard assembly. 4 &5/8s (notionally, +/- 1/8) is the measurement. Sounds like you have the incorrect mounting bracket (part1).
Second shot, next post, will show the the LH/RH brackets mounted on the tractor. You can see the detail of the RH bracket. Good luck---
Attachments
al3
Silver Member
Re: 4115 60\"deck MMM install help
This one shows the draft support brackets mounted to the frame. Arrows highlight brackets. Each is mounted to the frame using two bolts and nuts. (can't see the nuts in this pic becaue of the angle).
These are shots of a 4110. Ops manual says same parts used on 4110/4115, but no first hand knowledge of 4115. Good luck.
This one shows the draft support brackets mounted to the frame. Arrows highlight brackets. Each is mounted to the frame using two bolts and nuts. (can't see the nuts in this pic becaue of the angle).
These are shots of a 4110. Ops manual says same parts used on 4110/4115, but no first hand knowledge of 4115. Good luck.
