Mowing 8n with a 72" finish mower
- Thread starter ezzy
- Start date
- Views: 8657
hazmat
Elite Member
- Joined
- Feb 12, 2002
- Messages
- 4,051
- Location
- West Newbury, MA & Harrison, ME
- Tractor
- Kubota L5460HSTC
Re: 8n with a 72\" finish mower
yup.
Welcome to tbn. My TC18 (14 PTO HP) runs a 5 footer just fine. The 8n has a bit more HP...
PS no need to post in two different locations
yup.
Welcome to tbn. My TC18 (14 PTO HP) runs a 5 footer just fine. The 8n has a bit more HP...
PS no need to post in two different locations
Bob_Skurka
Super Member
- Joined
- Jul 1, 2003
- Messages
- 7,615
Re: 8n with a 72\" finish mower
I think the 8N had about 25 hp??? That would probably put the PTO hp about 18 or 19. Don't know how much torque there is in the engine but I think a 6' finish mower would probably work pretty well but might bog down with wet grass.
I think the 8N had about 25 hp??? That would probably put the PTO hp about 18 or 19. Don't know how much torque there is in the engine but I think a 6' finish mower would probably work pretty well but might bog down with wet grass.
Soundguy
Old Timer
- Joined
- Mar 11, 2002
- Messages
- 51,575
- Location
- Central florida
- Tractor
- RK 55HC,ym1700, NH7610S, Ford 8N, 2N, NAA, 660, 850 x2, 541, 950, 941D, 951, 2000, 3000, 4000, 4600, 5000, 740, IH 'C' 'H', CUB, John Deere 'B', allis 'G', case VAC
Re: 8n with a 72\" finish mower
According to the I&T service manual, which has its info from the nebraska tests. The 8n has 27.x belt hp.. and about 23.x pto hp. 9n and 2n tractors have a fraction less hp, due to a lower compression ratio ( 6:1 9/2n 6.5:1 8n ).
Lots of people run 6' finish mowers on there N's. Some like 5's if their lift is weak. If you are getting too much of a bit on the 6' swath.. just cut 5' or 5.5'
Soundguy
According to the I&T service manual, which has its info from the nebraska tests. The 8n has 27.x belt hp.. and about 23.x pto hp. 9n and 2n tractors have a fraction less hp, due to a lower compression ratio ( 6:1 9/2n 6.5:1 8n ).
Lots of people run 6' finish mowers on there N's. Some like 5's if their lift is weak. If you are getting too much of a bit on the 6' swath.. just cut 5' or 5.5'
Soundguy
djradz
Veteran Member
Re: 8n with a 72\" finish mower
I think you'll be fine. Two conditions could make it marginal - grass gettting too long and not able to fly out of the mower deck fast enough and second, going to fast of a ground speed. In either case, all you have to do is slow the ground speed a bit while keeping the RPMs up.
I think you'll be fine. Two conditions could make it marginal - grass gettting too long and not able to fly out of the mower deck fast enough and second, going to fast of a ground speed. In either case, all you have to do is slow the ground speed a bit while keeping the RPMs up.
higgy
Platinum Member
- Joined
- Jul 7, 2003
- Messages
- 590
- Location
- mid-south idaho
- Tractor
- Kuota L3130, Ford 9-n, Allis AC, and a JD 4020 with powershift
Re: 8n with a 72\" finish mower
I would be best if you put an overrunning clutch in the pto shaft to driveline connection as well. This can help if you need to stop in a hurry for some reason. There has been lots on this issue here. Try a search for overrunning clutch.
Dane
I would be best if you put an overrunning clutch in the pto shaft to driveline connection as well. This can help if you need to stop in a hurry for some reason. There has been lots on this issue here. Try a search for overrunning clutch.
Dane