OP
Garandman
Elite Member
- Joined
- Aug 3, 2014
- Messages
- 3,141
- Location
- Mount Sunapee NH / Dorchester, MA
- Tractor
- Kubota L3200 HST
I'm planning to put the switch in the fender, because easy.
Accessory plug on Kubota?
- Thread starter Garandman
- Start date
- Views: 42669
RoyJackson
Rest in Peace
- Joined
- Nov 17, 2001
- Messages
- 24,646
- Location
- Bethel, Vermont
- Tractor
- John Deere 4052R Cab,, Deere 855D UTV, Z920A Zero Turn Mower and assorted implements
That's where I wish I had installed my accessory outlet....installed in on the key panel instead. Just make sure you use a marine type outlet for better protection from the elements.
s219
Super Member
- Joined
- Dec 7, 2011
- Messages
- 8,607
- Location
- Virginia USA
- Tractor
- Kubota L3200, Deere X380, Kubota RTV-X
OP
Garandman
Elite Member
- Joined
- Aug 3, 2014
- Messages
- 3,141
- Location
- Mount Sunapee NH / Dorchester, MA
- Tractor
- Kubota L3200 HST
Found what may be the perfect switch - sealed motorcycle on/off switch.
Trail Tech 040-LS-B Black Push Button Light Switch. Available on Amazon.
I am thinking I'm going to drill a hole in the metal bracket that holds the tool box, near the right fender.
West Marine sells the similar Perko switch.
Trail Tech 040-LS-B Black Push Button Light Switch. Available on Amazon.
I am thinking I'm going to drill a hole in the metal bracket that holds the tool box, near the right fender.
West Marine sells the similar Perko switch.
OP
Garandman
Elite Member
- Joined
- Aug 3, 2014
- Messages
- 3,141
- Location
- Mount Sunapee NH / Dorchester, MA
- Tractor
- Kubota L3200 HST
OK, for extra credit, what is the required mating plug?
oosik
Epic Contributor
Ha,ha,ha. Almost caught me on that question. I know from experience that there are about X100 different plug types. I went to my local NAPA store, got matching male/female plug set. Clipped off the Kubota provided plug and used the mated set for the connection. Easy as pie.
OP
Garandman
Elite Member
- Joined
- Aug 3, 2014
- Messages
- 3,141
- Location
- Mount Sunapee NH / Dorchester, MA
- Tractor
- Kubota L3200 HST
Well, I've been to two auto parts stores (Advance and NAPA) and neither had anything that looks like this.
Tried Radio Shack, they had some two pin connectors but not 90 degree and not locking.
Tried Radio Shack, they had some two pin connectors but not 90 degree and not locking.
OP
Garandman
Elite Member
- Joined
- Aug 3, 2014
- Messages
- 3,141
- Location
- Mount Sunapee NH / Dorchester, MA
- Tractor
- Kubota L3200 HST
Fallon
Super Member
I just used 2 normal crimp spade connectors. Worked fine while I had it temporarily plugged in there, wasn't sealed or heavily secured though.
OP
Garandman
Elite Member
- Joined
- Aug 3, 2014
- Messages
- 3,141
- Location
- Mount Sunapee NH / Dorchester, MA
- Tractor
- Kubota L3200 HST
I've done a fair amount of boat [in salt water] and motor cycle accessory wiring. When I first started, it was "Whatever will get me back on the road/water fastest."
After learning the error of my ways, I'm now in the solder/dielectric grease/heat shrink tubing school. Once I connect it I don't ever want to think about the connection again, ever.
...Do want to use a connector for this though as I'm not sure how I'll like the light.
After learning the error of my ways, I'm now in the solder/dielectric grease/heat shrink tubing school. Once I connect it I don't ever want to think about the connection again, ever.
...Do want to use a connector for this though as I'm not sure how I'll like the light.
