Mansker
Bronze Member
Kenny: Awesome Job! Very well laid out and thought out, hat's off to you Kenny, I'll be waiting for your Grapple set-up so hurry Please! /forums/images/graemlins/grin.gif
Added Remote to FEL...
- Thread starter kennyd
- Start date
- Views: 34020
MMM
Platinum Member
Just my ignorance of your loader setup. My valves are mounted on loader mast and PB sleeve for most (Prince etc)loader valves are $30, a single spool w/relief about $60. Guess I missed the joystick part. Nice installation btw.
Wayne_H
Gold Member
- Joined
- Dec 16, 2004
- Messages
- 380
- Location
- Davidsonville, Maryland
- Tractor
- John Deere 4400, '48 B and 318
Kenny:
When we going to start cut and welding some metal for that thing!!!!!
Wayne /forums/images/graemlins/cool.gif
When we going to start cut and welding some metal for that thing!!!!!
Wayne /forums/images/graemlins/cool.gif
sanman
Member
kenny:
very nice! hey, did you drill holes all the way through the loader frame to mount your valve or did you do some welding or something?
very nice! hey, did you drill holes all the way through the loader frame to mount your valve or did you do some welding or something?
OP
kennyd
Advertiser
SanMan,
The 3 mounting hole(5/16") are only drilled through one side on the mast. The bottom of the mast is open, so I just reached up inside to put the washers and nylock nuts on.
The 3 mounting hole(5/16") are only drilled through one side on the mast. The bottom of the mast is open, so I just reached up inside to put the washers and nylock nuts on.
sanman
Member
thanks:
I'am about to get started on set of grapples for my L3130.The mast an arm setup is a little different than yours but I do have room on the inside of the arm.
Since mine is tubular I was wondering do you think its ok to drill through or maybe weld some bolts on and slip the valve onto them with nuts an washers.
I'am about to get started on set of grapples for my L3130.The mast an arm setup is a little different than yours but I do have room on the inside of the arm.
Since mine is tubular I was wondering do you think its ok to drill through or maybe weld some bolts on and slip the valve onto them with nuts an washers.
OP
kennyd
Advertiser
Sanman,
I am hesitant to answer that question without seeing the setup you have, any chance of posting pics of the loader mast?
I did not pre-plan the location of the diverter valve, I ordered it and then when I had it in hand, set out to find the best, most out-of-the way place to mount it. If you are sure you are going to do this, go ahead and order just the valve.
Good Luck
I am hesitant to answer that question without seeing the setup you have, any chance of posting pics of the loader mast?
I did not pre-plan the location of the diverter valve, I ordered it and then when I had it in hand, set out to find the best, most out-of-the way place to mount it. If you are sure you are going to do this, go ahead and order just the valve.
Good Luck
sanman
Member
kenny:
the loader frame is raised alittle bit to get a better view.the top two hoses are bucket curl, and I was thinking about mounting the valve between the loader pin and metal connectors which is about 12or13".
L the loader valve hoses to diverter IN, loop short hoses from OUT to the metal line connectors and L lines from diverter ports to grapple cylinder QD's.
the loader frame is raised alittle bit to get a better view.the top two hoses are bucket curl, and I was thinking about mounting the valve between the loader pin and metal connectors which is about 12or13".
L the loader valve hoses to diverter IN, loop short hoses from OUT to the metal line connectors and L lines from diverter ports to grapple cylinder QD's.
Attachments
sanman
Member
TobyH
Silver Member
That is a very cool setup. All gizmo freak grease monkeys are drooling! I haven't played with or thought it through but does anyone think this same setup could be modified to run remote tools like a log splitter or hydraulic jackhammer?