littlediesel
Silver Member
- Joined
- May 11, 2002
- Messages
- 161
- Location
- Baldwinsville, New York
- Tractor
- L45 TLB, U35, KX71, U17 Excavators, B3030HSDC, F3680, ASV PT40
B2910 3rd valve
- Thread starter littlediesel
- Start date
- Views: 728
ronjhall
Super Star Member
<font color=blue>Has anyone purchased or installed a 3rd valve for their B2910?</font color=blue>
Jon
Here is a thread on how to install Top and Tilt on a B27-2910 tractor. It was started by TBN’s Star member Bird. /w3tcompact/icons/smile.gif It is quite lengthy. But has all the information that is required to add a third and fourth valve.
<A target="_blank" HREF=http://www.tractorbynet.com/cgi-bin/compact/showflat.pl?Cat=&Board=owning&Number=32151&page=&view=&sb=&o=&fpart=all&vc=1>Click Here</A>
Here is a link to the original thread that is even longer. /w3tcompact/icons/eyes.gif <A target="_blank" HREF=http://www.tractorbynet.com/cgi-bin/compact/showthreaded.pl?Cat=&Board=owning&Number=24170&page=&view=&sb=&o=&vc=1#Post24170>Click Here</A>. You will find some of the pictures are missing. When Muhammad did the conversion to the current format these pictures were lost from the post. /w3tcompact/icons/frown.gif
<font color=blue>If so, how much did it cost you and how did you do it?</font color=blue>
Cost will depend on finding a valve. I was lucky; my dealer had a valve left over from a blade he installed on a tractor. His price for a 2-spool valve was less than a single valve at TSC. Using the rear Auxiliary Hydraulics outlet is explained on page 39 of my operator’s manual. If I remember the price for the outlet ran from $60 to $100 depending on how much discount dealer was giving. /w3tcompact/icons/shocked.gif
If you install the valve yourself, price should run between $200 and $300 dollars.
Installation is explained in the 2 treads above. Even though the treads are about Top & Tilt, The main part of this conversion is installing the valves. If you have any additional questions you should be able to find the answers here on TBN.
Jon
Here is a thread on how to install Top and Tilt on a B27-2910 tractor. It was started by TBN’s Star member Bird. /w3tcompact/icons/smile.gif It is quite lengthy. But has all the information that is required to add a third and fourth valve.
<A target="_blank" HREF=http://www.tractorbynet.com/cgi-bin/compact/showflat.pl?Cat=&Board=owning&Number=32151&page=&view=&sb=&o=&fpart=all&vc=1>Click Here</A>
Here is a link to the original thread that is even longer. /w3tcompact/icons/eyes.gif <A target="_blank" HREF=http://www.tractorbynet.com/cgi-bin/compact/showthreaded.pl?Cat=&Board=owning&Number=24170&page=&view=&sb=&o=&vc=1#Post24170>Click Here</A>. You will find some of the pictures are missing. When Muhammad did the conversion to the current format these pictures were lost from the post. /w3tcompact/icons/frown.gif
<font color=blue>If so, how much did it cost you and how did you do it?</font color=blue>
Cost will depend on finding a valve. I was lucky; my dealer had a valve left over from a blade he installed on a tractor. His price for a 2-spool valve was less than a single valve at TSC. Using the rear Auxiliary Hydraulics outlet is explained on page 39 of my operator’s manual. If I remember the price for the outlet ran from $60 to $100 depending on how much discount dealer was giving. /w3tcompact/icons/shocked.gif
If you install the valve yourself, price should run between $200 and $300 dollars.
Installation is explained in the 2 treads above. Even though the treads are about Top & Tilt, The main part of this conversion is installing the valves. If you have any additional questions you should be able to find the answers here on TBN.
