BigDogues
Gold Member
I received my replacement tie rod yesterday. /forums/images/graemlins/laugh.gif Ordered on 9/8 received on 9/19. Not too bad for a back ordered part. /forums/images/graemlins/smirk.gif
bent tie rod
- Thread starter DrewL
- Start date
- Views: 6592
Mavrik02
Silver Member
Hey, I bent my left handed axle housing gear pin actuator last week! I switched it with an extra right handed torque extender pin and everything was fine. /forums/images/graemlins/tongue.gif
The way I use my machine I might be better off ordering a tie rod now...its only a matter of time...
The way I use my machine I might be better off ordering a tie rod now...its only a matter of time...
Hey, I bent my left handed axle housing gear pin actuator last week! I switched it with an extra right handed torque extender pin and everything was fine
tell us how you did that? left and right are not interchangeable unless you.................swapped ends???!!!
I thnk it was said best that if the tie rod is bent in the future, just adjust the toe in and keep on truckin'. The front wheels don't know the tie rod is bent. There is a good thing about this that if you do bend the tie rod, put the bent area towards the motor so it doesn't hang down so low............hhhhmmm /forums/images/graemlins/smirk.gif
tell us how you did that? left and right are not interchangeable unless you.................swapped ends???!!!
I thnk it was said best that if the tie rod is bent in the future, just adjust the toe in and keep on truckin'. The front wheels don't know the tie rod is bent. There is a good thing about this that if you do bend the tie rod, put the bent area towards the motor so it doesn't hang down so low............hhhhmmm /forums/images/graemlins/smirk.gif
sammi
Member
Ok ok I give up...this must be important..can someone please tell me what the left handed axle housing gear pin actuator is and what it's used for?
All these people breakin/bending stuff...don't want that to happen to m Ck20hst....
Does my ck even have one of these?
All these people breakin/bending stuff...don't want that to happen to m Ck20hst....
Does my ck even have one of these?
DK35vince
Super Member
</font><font color="blue" class="small">( Ok ok I give up...this must be important..can someone please tell me what the left handed axle housing gear pin actuator is and what it's used for?
Does my ck even have one of these? )</font>
No, and neither does theirs..
Does my ck even have one of these? )</font>
No, and neither does theirs..
sammi
Member
Wheww...Thanks Dk for letting me know...one less thing to worry about....um..what about the right handed torque extender pin?
I need some rest.. my head hurts.. /forums/images/graemlins/smile.gif
I need some rest.. my head hurts.. /forums/images/graemlins/smile.gif
And to make matter worse they are all runnning low on Blinker fluid and as AJ would say "the torque converter's runnnin' low on torque"... /forums/images/graemlins/grin.gif
Sammi>> not trying to bust yer chops here.. we all have days like that, but you brought tears to my eyes with all that.. have a good one my friend... /forums/images/graemlins/wink.gif
Sammi>> not trying to bust yer chops here.. we all have days like that, but you brought tears to my eyes with all that.. have a good one my friend... /forums/images/graemlins/wink.gif
MotorSeven
Elite Member
Ahh, like the 'ole "sticky kanooter valve" problem....LOL!
Kiohio
Platinum Member
I wish I had a picture of the link that a customer bent in half on a 3054. The steel bent into a big "U" before it snapped the tierod threads. bent it str8 and borrowed my favorite Lancaster natives welder and weld the end back on, so I could get it loaded on the truck.
KO
KO