Front-End Loader Danuser Intimdator

[2manyrocks]

The advantages of the hydraulic tree puller seem to be that you don't have to get off the tractor, you can push and pull the tree, and then you can more easily move the tree once its uprooted. The $4,500 price tag vs $50 for a chain and pipe seems pretty steep.

Your psi numbers are similar to those stated in a Messick's video on youtube warning about psi spikes when using a grapple. The Messick's video said some grapples come with a check valve to limit pressure, but I've yet to figure out how to incorporate some kind of overpressure protection for the MTL grapple I bought. So it's still sitting on the pallet, unused, and I have yet to install any kind of third function kit, either.

Is there some way of adding overpressure protection when installing a third function kit?

 

[Smokeydog]

Best protection is operator understanding of equipment limitations and technique.

Some of the large skid steer grapples use cushion valves on the grapple lids. Used a cushion valve for protection on a hydraulic top link of a 3pt log grapple. Could lift a 30’ log off the ground long ways.

Let the grapple lids grip and use healthy respect when pulling or pushing with them. Most can figure out grapple use and find them highly productive attachments without damaging their tractor.

 

[2manyrocks]

Is a cushioning valve expensive or hard to install? Not knowing anything about this myself, is there a reason not to add a cushioning valve?

edit: further...I wonder if I could modify the lower tines on my grapple to incorporate a tree puller for smaller trees (1-3") and perhaps have a manual diverter valve assembly on the grapple to switch between the puller function and the grapple lid function.

Not looking to pull 5" trees with my L2501. But I can see the utility of being able to pull some smaller trees without resorting to the chain method.

 

[Vigo327]

How hard it is depends on how much hydraulic plumbing you've done before. If you've done a lot then it will be easy. It has to be set up for a pressure higher than your relief valve but lower than when hoses burst and metal starts bending. I haven't used one yet, myself.

With pullers like this, or stump buckets, one of the ways you can get some extra force is by pivoting the implement on something so that your hydraulic curl force is pulling up on the tree or whatever, but the weight of the front of your machine is also pushing down on the back of the implement, and if it's pivoting on something in the middle, you get more curl force at the end from using your tractor to 'see-saw' the puller/bucket. This is why a lot of stump buckets have curved bottoms, to build-in that pivot point. I haven't seen the same on tree pullers (flat bottoms) but you could create the effect easily, even with a 6x6 wood post or a rock as your pivot.

 

[Smokeydog]

Danuser has good instructional instructions and videos. Grip low, lift and drive forward greatly increases pulling force. The excavator teeth and cutting edges easily breaks and cuts roots to help extract trees. Helps with even small tractors like the B26 tackle trees safely. Especially invasive species. Pull roots and fill in the hole.

My point is how surprised how well this attachment is useful on a small HP tractor. Absolutely a tree and rock “Intimdator “ on 60hp tractor.

 

[shooterdon]

Good thread. I wanted to get one of these but could not justify the cost. Bought a tree and post puller and wish I had bitten the bullet.

With my tractor it near impossible to see what I am doing so I had to add a camera system.

 

[nancyk]

View attachment 749460

The pipe bites and allows the grab hook chains to slip. Grabs slippery and small stems. Also rocks.

Can you show a picture how this works? I am having a hard time imagining how it is placed on a young tree. I do the wrap method also, time consuming for the small trees.
O.K., I think I see it now. The base of the tree goes in the loop area of the chain. So you have to insert the chain into the pipe each time you use it, correct?

 

[Smokeydog]

Can you show a picture how this works? I am having a hard time imagining how it is placed on a young tree. I do the wrap method also, time consuming for the small trees.

The pipe does two things.
First it allows a grab hook chain to slip or choke the load when pulled. Tightening around the tree.
Second the pipe end edges bite into the tree for better grip.

Just have to make one loop around the tree and hook into the pipe. Self tightens when pulling. The loop at the bottom goes around the tree.

Simple but highly effective tool for slippery stems or brush bunches like Russian olive, privet or multiflora roses. Can loop it wide and pull tight saves from crawling underneath.

A slip hook works too but doesn’t have the pipe edges to bite and slips off. Spring time the barks gets real loose and slippery.

Often hook up both ends of chain/pipes to different trees and pull out at the same time.

Wife bought me a fancy spring loaded, wicked looking, spiked grabber from Northern tool. This simple frontier tool works better, easier and faster.

 

[nancyk]

The pipe does two things.
First it allows a grab hook chain to slip or choke the load when pulled. Tightening around the tree.
Second the pipe end edges bite into the tree for better grip.

Just have to make one loop around the tree and hook into the pipe. Self tightens when pulling. The loop at the bottom goes around the tree.

Simple but highly effective tool for slippery stems or brush bunches like Russian olive, privet or multiflora roses. Can loop it wide and pull tight saves from crawling underneath.

A slip hook works too but doesn’t have the pipe edges to bite and slips off. Spring time the barks gets real loose and slippery.

Often hook up both ends of chain/pipes to different trees and pull out at the same time.

Wife bought me a fancy spring loaded, wicked looking, spiked grabber from Northern tool. This simple frontier tool works better, easier and faster.

can you give the dimensions of this pipe? I asked a friend if he can get this pipe fabricated for me(as I have the necessary chains and hooks). he asked for more pictures, not quite sure why. I had given him the picture from your post. Maybe the dimensions would help him.
I found a scrap piece of thick-wall pvc, cut an opening out of it with a sawzall and will try that.

 

[oosik]

That might work for thinning my pine stands. 800 - 1200 small ( 1" to 6" on the butt ) pines. Every other year now. I use a chain saw for a couple reasons. It's really quick - it leaves the root ball in the ground. I end up dragging these pines to collection piles and then chipping them. I do not want to be running root balls thru my chipper.

With my little Stihl - I average 150 to 175 pines cut out per hour. I've found it works best if I take a half hour break every two hours or so.