dressin' up an old YM187

   / dressin' up an old YM187
  • Thread Starter
#111  
Re: dressin\' up an old YM187

PoconoMan, Jwnge, Jagmandave, Awlchu, Fig, Golfgar4,
Tim in Ia. & Thegreatrandini

<font color="blue">By the way, for a "redneck paint booth" it sure looks nice with that nice clean concrete floor!</font>

Me and a broom got to be good buddy's during this process /forums/images/graemlins/grin.gif it was constance keeping the area as clean as I could

<font color="blue">it looks great, like a puller with those big tires </font>

Kinda look as if you could climb a tree with the thing /forums/images/graemlins/smile.gif

<font color="blue">Are you ready to go into business now in Asia tractor repair?</font>

I think not /forums/images/graemlins/grin.gif, but ya know I learned an awful lot about this little tractor and how it's put together in this process and wouldn't think twice about splittin' it for a clutch or guttin' the engine for an overhaul.....well I think I would anywho!

<font color="blue">Where's the picture of the proud owner with his newly renovated jewel??</font>

Belive me....the tractor is a lot better lookin' than I am /forums/images/graemlins/blush.gif

<font color="blue">You didn't comment I don't think but I am sure it runs great too after all that TLC?</font>

Ya know, I thought bleeding the fuel system was going to be a pain....all I had to do was bleed from the tank to the filter, across the filter and to the injector pump and it poped right off! /forums/images/graemlins/grin.gif
I wan't sure about the hyd. pump with it being dry for so long. Filled the tranny and it did take a bit for the 3PT. lift to make some movement but all I did was move the lever back and forth for a bit and it came to life.

<font color="blue">Your skills surpass mine.</font>

Randy, this was all learned on the fly sorta speek, I didn't even own a compressor and paint gun before I started this and I've never so much as held a air spray gun, belive me if I can do it anyone can.......just gotta get through the learnin' curve! /forums/images/graemlins/wink.gif

Guys, thanks again for the comments and following along, there were times I thought I may have been driving you-all nuts with pic's /forums/images/graemlins/blush.gif
 
   / dressin' up an old YM187 #112  
Re: dressin\' up an old YM187

As the say to the weekend golfer after a 300 yd. drive down the middle, "GIT A JOB!!". You have entirely too much spare time on your hands. Great work.
 
   / dressin' up an old YM187
  • Thread Starter
#113  
Re: dressin\' up an old YM187

normde2001:

Wasn't it you who told me in the begining to "just wax it"? and I have a job...thats why it took so long to get it done /forums/images/graemlins/grin.gif
 
   / dressin' up an old YM187 #114  
Re: dressin\' up an old YM187

Whiskey,

Great looking tractor. In fact the whole tutorial was outstanding, including the trial and error periods where you stated not good enough and had to re-sand and paint certain parts over again.

I know a little about paint and restoration work and I think it is an outstanding finished product. And for your very first effort it appears to be flawless.

Great job. Regards. Mark
 
   / dressin' up an old YM187 #115  
Re: dressin\' up an old YM187

Whiskey, great job on the tractor! Thanks for all of the updates and pictures, I really enjoyed following this thread as I'm sure many others did.

You are a bad influence though, I was at Lowe's over the weekend and happen to walk past the air tools and just had to stop and check out paint guns. Never was even remotely intersted before... /forums/images/graemlins/smile.gif

Chuck
 
   / dressin' up an old YM187
  • Thread Starter
#116  
Re: dressin\' up an old YM187

Mark:

Thanks for the comments

<font color="blue">In fact the whole tutorial was outstanding, including the trial and error periods where you stated not good enough and had to re-sand and paint certain parts over again.
</font>

I tried to lay it out as I would like to see it if someone else was postin' and I was looking & reading /forums/images/graemlins/grin.gif
 
   / dressin' up an old YM187
  • Thread Starter
#117  
Re: dressin\' up an old YM187

cwarrix:

<font color="blue">You are a bad influence though, I was at Lowe's over the weekend and happen to walk past the air tools and just had to stop and check out paint guns. Never was even remotely intersted before...</font>

Ya know......I think you should buy it.....it's sign /forums/images/graemlins/blush.gif thats where I got my gun at /forums/images/graemlins/grin.gif
 

Tractor & Equipment Auctions

2023 JOHN DEERE 8R310 LOT NUMBER 203 (A53084)
2023 JOHN DEERE...
1990 Ingersoll Rand 185 Towable Diesel Air Compressor (A52377)
1990 Ingersoll...
NEW Ripper Shank (A53002)
NEW Ripper Shank...
(1) Drum of Algicide (A51573)
(1) Drum of...
BUYERS PREMIUM & PAYMENT TERMS (A52576)
BUYERS PREMIUM &...
1264 (A50490)
1264 (A50490)
 
Top