FX24D issues
- Thread starter coolbrze
- Start date
- Views: 4561
runningbird
Gold Member
is the 3pt dropping a bit then suddenly raising?
normde2001
Elite Member
- Joined
- Mar 10, 2002
- Messages
- 4,159
What do you mean by "running"? Is it moving, just sitting idling, hydraulics working?
Yes but the entire tractor kinda "pulsates"
When it's sitting idling still although may do it when moving but if so, it's harder to notice but I'll pay more attn. next time I drive it. Hydraulics work but bucket doesn't stay up very well once you put weight in it...
runningbird
Gold Member
does the 3pt stay up when the tractor is off?
YanmarFever
Elite Member
- Joined
- Mar 10, 2002
- Messages
- 4,106
- Location
- Eating a melon..
- Tractor
- Branson 4520r 5520C- Yanmar FX235-D - Bad Boy rogue mower
1. Have you cleaned the Hydraulic filter screen lately? Its located on the under side of the machine
2. Also it sounds like your 3 point adj arm is out of adjustment, did you turn on it with a wrench where it comes out of the tractor top end?
3. Did you turn the 3 point adj knob, its located right between your ankles when seated on the tractor.
4. Do you have the correct hydraulic filter installed, ( if not) it will pulsate because its not circulating enough fluid.
Lots of questions...
2. Also it sounds like your 3 point adj arm is out of adjustment, did you turn on it with a wrench where it comes out of the tractor top end?
3. Did you turn the 3 point adj knob, its located right between your ankles when seated on the tractor.
4. Do you have the correct hydraulic filter installed, ( if not) it will pulsate because its not circulating enough fluid.
Lots of questions...
Sorry for the delayed reply, been busy working. No the 3 point hitch goes down almost immediately when I turn the tractor off but the FEL stays up.
YanmarFever
Elite Member
- Joined
- Mar 10, 2002
- Messages
- 4,106
- Location
- Eating a melon..
- Tractor
- Branson 4520r 5520C- Yanmar FX235-D - Bad Boy rogue mower
Have you checked the 4 things mentioned in the post above?
kenmac
Super Member
- Joined
- Feb 13, 2005
- Messages
- 9,961
- Location
- The Heart of Dixie
- Tractor
- McCormick CX105 Kubota MX 5100 HST,
my 3110 does this. I think it's the 3 point valve. I haven't replaced it yet. Last I checked, they didn't have any
clemsonfor
Super Member
Good to hear from you Ernie
YanmarFever
Elite Member
- Joined
- Mar 10, 2002
- Messages
- 4,106
- Location
- Eating a melon..
- Tractor
- Branson 4520r 5520C- Yanmar FX235-D - Bad Boy rogue mower
Clem, I still hang around when I have the chance, I cant shake that yanmar fever that bit me so long ago..
normde2001
Elite Member
- Joined
- Mar 10, 2002
- Messages
- 4,159
Aren't you hiding out somewhere in the Bahamas these days? I also am "In the palm trees by the sea", (Ft. Lauderdale, Fl.).
California
Super Star Member
- Joined
- Jan 22, 2004
- Messages
- 16,869
- Location
- An hour north of San Francisco
- Tractor
- Yanmar YM240 Yanmar YM186D
Ernie we miss your good advice, and humor.
YanmarFever
Elite Member
- Joined
- Mar 10, 2002
- Messages
- 4,106
- Location
- Eating a melon..
- Tractor
- Branson 4520r 5520C- Yanmar FX235-D - Bad Boy rogue mower
Thanks for the ideas Ernie. I'm not familiar w/ this tractor, just bought it last Fall. Where is the hydraulic filter screen located underneath / what does it look like? I have not messed w/ the adjuster knob, all that does is regulate the speed that the 3 pt hitch moves, correct? I haven't changed the hyd fluid or filter since purchasing, guess I should do that. What kind of fluid & what filter does it take? I don't have a manual for this tractor & y'all have been a wealth of info so far!
If you look right at the back end of the running board and a little lower you will see two 3 bolt flanges. Your screen is behind the lower one.
This is your spin on filter. HYDRAULIC FILTER - SPIN-ON: Yanmar Tractor Parts
This is your spin on filter. HYDRAULIC FILTER - SPIN-ON: Yanmar Tractor Parts
Attachments
Last edited:
Thanks like usual Winston! Should I clean or just replace the screen right now & how often should I do that?
clemsonfor
Super Member
the knob under the seat IS NOT used to control 3pt descent speed, it is a service knob that locks out the system and will hold the fluid inside the piston for service. To control the speed there is a different mechanism on the side of the top of the 3pt under the seat that has a 90 degree lever on it push it one way to slow it and push it the other to increase the speed it falls. The knob under the seat between your knees should always be open unless your using it to diagnose 3pt problems or some other task like that.
