Buppies
Veteran Member
- Joined
- Oct 26, 2011
- Messages
- 1,151
- Location
- SouthWestern Virginia
- Tractor
- Kubota L5240 EX mark 60 in 29 hp Toro 60inch Z Master 21 inch walk behind Polaris 900 hunter edition 30in toro walk behind
Wonderful picture riptides
Good morning!!!!
- Thread starter 300UGUY
- Start date
- Views: 18298212
RedNeckGeek
Platinum Member
- Joined
- Jan 1, 2011
- Messages
- 969
- Location
- Butte County & Orcutt, California
- Tractor
- Kubota M62, Kubota L3240D HST (SOLD!), Kubota RTV900
But tonight, I'm workin' on Wasting Away In Margaritaville...:laughing::drink:
LS Tractor Owner
Elite Member
- Joined
- May 1, 2017
- Messages
- 3,831
- Location
- Edgewood, NM
- Tractor
- LS XG3025 TLB, Previously MT125 TLB, Craftsman GTS6500
Drew, our thoughts and prayers are with you! You will overcome this!
LS Tractor Owner
Elite Member
- Joined
- May 1, 2017
- Messages
- 3,831
- Location
- Edgewood, NM
- Tractor
- LS XG3025 TLB, Previously MT125 TLB, Craftsman GTS6500
Wonderful and beautiful pictures! I forget how green the mountains and valleys are back there!
Thomas, you had a great popsicle and a show! I am glad the store owner held his ground.
Did not do any of the electrical today... got side tracked.... cut, sanded, finished, and installed 3 plant shelves for the wifey... more important to do first.
Then spent a couple hours helping DIL rearranging their stored items in the shed. She consolidated a bunch of stuff and took a bunch of stuff to donate.
An easier day for sure, but time consuming.... still has to get done, so that is ok.
Everyone have a great evening!
Thomas, you had a great popsicle and a show! I am glad the store owner held his ground.
Did not do any of the electrical today... got side tracked.... cut, sanded, finished, and installed 3 plant shelves for the wifey... more important to do first.
Then spent a couple hours helping DIL rearranging their stored items in the shed. She consolidated a bunch of stuff and took a bunch of stuff to donate.
An easier day for sure, but time consuming.... still has to get done, so that is ok.
Everyone have a great evening!
rswyan
Super Member
- Joined
- May 12, 2004
- Messages
- 5,248
- Location
- Northeast Ohio
- Tractor
- Kubota B2910, Cub Cadet Pro Z 154S, Simplicity 18 CFC, Cub Cadet 782
Just removed the gland nut:
Unfortunately there is a good amount of wear in the rod end hole for the pin ... probably should be machined and sleeved ...
Unfortunately there is a good amount of wear in the rod end hole for the pin ... probably should be machined and sleeved ...
rswyan
Super Member
- Joined
- May 12, 2004
- Messages
- 5,248
- Location
- Northeast Ohio
- Tractor
- Kubota B2910, Cub Cadet Pro Z 154S, Simplicity 18 CFC, Cub Cadet 782
Rod does not appear bent:
Nor are there any obvious scratches or pitting.
Will need to check it with a straight edge though.
Nor are there any obvious scratches or pitting.
Will need to check it with a straight edge though.
rswyan
Super Member
- Joined
- May 12, 2004
- Messages
- 5,248
- Location
- Northeast Ohio
- Tractor
- Kubota B2910, Cub Cadet Pro Z 154S, Simplicity 18 CFC, Cub Cadet 782
Seal kit contains a total of 11 seals/o-rings:
That’s for one cylinder.
That’s for one cylinder.
toppop52
Veteran Member
- Joined
- Oct 19, 2011
- Messages
- 1,901
- Location
- Eastern Shore of Maryland
- Tractor
- Massey Ferguson 1723, Cub Cadet 1864
toppop52
Veteran Member
- Joined
- Oct 19, 2011
- Messages
- 1,901
- Location
- Eastern Shore of Maryland
- Tractor
- Massey Ferguson 1723, Cub Cadet 1864
Great sunset Rip!
lostcreekranch
Elite Member
- Joined
- Dec 14, 2012
- Messages
- 4,947
- Location
- Austin County, Texas
- Tractor
- NH TL-100A with Bush Hog 5045 FEL, WR Long 3rd function, LS XR4155HC w/FEL, WR Long 3rd Function.
