Hay Loader?
- Thread starter nomad
- Start date
- Views: 1938
HayDR
Veteran Member, Approved Advertiser
Amish Hay Loader
DaveNay
Platinum Member
- Joined
- Aug 13, 2003
- Messages
- 834
- Location
- Waterman, DeKalb County, Illinois
- Tractor
- John Deere 855 MFWD; Oliver 1850 Gas
Amish Hay Loader Pt. II
Dave
Robert_in_NY
Super Member
- Joined
- Aug 1, 2001
- Messages
- 8,552
- Location
- Silver Creek, NY
- Tractor
- Case-IH Farmall 45A, Kubota M8540 Narrow, New Holland TN 65, Bobcat 331, Ford 1920, 1952 John Deere M, Allis Chalmers B, Bombardier Traxter XT, Massey Harris 81RC and a John Deere 3300 combine, Cub Cadet GT1554
While I am a Turk I make no claims to have the best products. I do think New Holland makes some darn good ones though.
Taylortractornut
Elite Member
- Joined
- Mar 27, 2002
- Messages
- 2,770
- Location
- Iuka Mississippi USA
- Tractor
- 3550 Fard Backhoe and a 1948 Farmall Cub,
Here we use scissor type lifts with a hay fork to stack round bales 2 bales high or one bale high on a trailer or hay wagon. I usually take a few forklift front ends and make them 3 point attachments to load baled 3 hight on a trailer but it takes a good sized tractor. To load square bales or smaller round bales i use a chain loader in a metal frame its just a modified conveyor belt using ag chain with a spike welded in it every few feet. Back several years aboug they had a home built hayloder that tattchet to trh front or sides of tractors to convey the hay bales uop over the tractor onto the stack.
Taylortractornut, your hay loader (with scissor type lifts with a hay fork) is a home-built one? If not, I'l be glad if you can show its picture on the net. It seems that capacity of yours is not more than 500 lb. What I am looking for is to load 1500-2000 lb of hay by a tractor-back loader. Anyways, thanks for the info.
Robert in NY, you are a Turk? I thought you were Turk. So, you think Turk products are not the best? At least 2 people here don't agree with you in that. They are CCI and I. I see there are many more people out there who don't agree with you. If this wasn't so, the best selling tillers there in USA would not have been Turk tillers.
Robert in NY, you are a Turk? I thought you were Turk. So, you think Turk products are not the best? At least 2 people here don't agree with you in that. They are CCI and I. I see there are many more people out there who don't agree with you. If this wasn't so, the best selling tillers there in USA would not have been Turk tillers.
Robert_in_NY
Super Member
- Joined
- Aug 1, 2001
- Messages
- 8,552
- Location
- Silver Creek, NY
- Tractor
- Case-IH Farmall 45A, Kubota M8540 Narrow, New Holland TN 65, Bobcat 331, Ford 1920, 1952 John Deere M, Allis Chalmers B, Bombardier Traxter XT, Massey Harris 81RC and a John Deere 3300 combine, Cub Cadet GT1554
I didn't say that Turks don't make good products but no one country makes the best of everything. I am proud of my work but I do know others who can do a lot better job then I could. That is all I was trying to say. This board has a lot of US members and it doesn't help you to come out and bash the US products. The USA makes some good products as does Canada, Germany.... and so on but none of these countries can lay claim to making all the best products.
Slamfire
Veteran Member
I've used one of those, but my favorite for loose hay was an elevator/rake that followed the wagon. Ground driven it lifted hay to dump in the wagon. Kept two good men busy movin' all that hay to the front of the wagon. /forums/images/graemlins/tongue.gif
Taylortractornut
Elite Member
- Joined
- Mar 27, 2002
- Messages
- 2,770
- Location
- Iuka Mississippi USA
- Tractor
- 3550 Fard Backhoe and a 1948 Farmall Cub,
Namad on a 4000 Ford an oldermodel Ive picked up 1500 pound bales wit hthe scissor type both factory and homemade units. I may one now that attaches to the 3 point hitch but it has a cylinder that raises the boom up and one cylinder that dumps the hay. Its a bit easier on the tractors lift. I dont have one made yet but i can try to dig up a few pics. I make mine to hold a bucket or a boom and and spear or forks. With this type you can raise the 3 point and then raise the clinders agin giving more lift height.
