Spanner
Veteran Member
Did you put Loctite or similar thread-locker on the screw threads?
JD 755 Project
- Thread starter lumberbean
- Start date
- Views: 19230
-
- Tags
- john deere 755
beenthere
Super Star Member
- Joined
- Aug 16, 2001
- Messages
- 18,453
- Location
- Southern Wisconsin, USA
- Tractor
- JD_4x2_Gator, JD_4300, JD_425, JD_455 AWS, added JD_455, JD_110, JD_X485(sold)
No, no.. Just the filter element. Pleated paper thingy. Install with the hole in one end upwards. It fits on the stub in the top of the housing head and will stay there while you fit the bowl and screw-ring over it.
I have seen several fitted upside-down. (Don't ask...)
What happens if installed incorrectly? Curious, as don't think I've been aware of the fitting to the stub on my 4300, but do see that one end of the filter is open (hole) and other end closed.
Spanner
Veteran Member
The 'hole' fits over an O-ring on the stub which is the outlet to the injection pump.
Push it up. If it stays up, you're good. If it falls off try again...
With the bowl fitted the filter element is pressed up by the spring for security.
Diesel fuel enters the filter bowl, passes through the filter paper and is drawn up the middle to the IP.
Upside down - the closed end sits against the outlet hole in the stub, pressed up by the spring again but blocking the outlet, nearly. It usually sits a bit crooked and fuel can pass but it is not filtered as it, effectively, goes around the outside of the element.
Push it up. If it stays up, you're good. If it falls off try again...
With the bowl fitted the filter element is pressed up by the spring for security.
Diesel fuel enters the filter bowl, passes through the filter paper and is drawn up the middle to the IP.
Upside down - the closed end sits against the outlet hole in the stub, pressed up by the spring again but blocking the outlet, nearly. It usually sits a bit crooked and fuel can pass but it is not filtered as it, effectively, goes around the outside of the element.
beenthere
Super Star Member
- Joined
- Aug 16, 2001
- Messages
- 18,453
- Location
- Southern Wisconsin, USA
- Tractor
- JD_4x2_Gator, JD_4300, JD_425, JD_455 AWS, added JD_455, JD_110, JD_X485(sold)
tks
Am sure it is right, but will take a second look to be sure.
Am sure it is right, but will take a second look to be sure.
Spanner
Veteran Member
In the 4300 you have the benefit of the 'Red Ring' which indicates the presence of water when it floats up off the bottom of the bowl.
Item 16 >
The central hole in the 'top' of the filter element is also shown here:
I mis-wrote. :ashamed: The O-ring seal is in the 'hole' of the filter element. It grips onto the outlet stub.
Item 16 >
The central hole in the 'top' of the filter element is also shown here:
I mis-wrote. :ashamed: The O-ring seal is in the 'hole' of the filter element. It grips onto the outlet stub.
OP
lumberbean
Member
Yes, Loctite was applied to the screw threads so I'm hoping it will last. I'm going to check the hose tonight when I get home and let you know if it goes up to the engine block.
JD755
Platinum Member
It does look like the fuel fill overflow tube. They degrade and pull away from the fitting just below the fuel cap.
Spanner
Veteran Member
That's true, they do.
OP
lumberbean
Member
Just wanted to give an update on the 755 and say "Its alive!". I was able to get it started this past Saturday and drove it around my yard a few times. Some things I noticed on it:
Start up: I followed the operator's manual precisely and the engine fired up first time trying. A little bit of black smoke and that was it.
Power steering: Its great and I didn't anticipate how easy it would be to turn the steering wheel. My Cub Cadet zero turn is much more difficult to say the least.
Parking Brake: didn't think it worked but turned out it does just the lever doesn't move that far up.
Tachometer/Odometer: The tach isn't working and I'm pretty sure that the hour meter isn't as well. I'll have to look at fixing both in the future.
Loader: the loader works fine and is able to go up and down without any problems.
Hydraulic Lines: Surprisingly, no leaks on them which I was glad.
Front right tire: has a small hole in it that needs plugged. I'll get to this weekend.
Fuel tank: I knew I had to replace it going in and when I bought it, it came with a new one. The old one leaks pretty badly if filled to high. I'll hope to fix this by weeks end. The previous owner said that he ran out of gas one time and had to re-prime the fuel system which was pretty time consuming and painful. I'm hoping it won't be that bad.
Fuel pump: I noticed a little bit of fuel dripping from the line or the pump, not sure. I might buy a new clamp and see if that fixes it.
We didn't end up using the left over HyGard on the tractor because it looked like it had been previously opened and weren't really sure if it was hydraulic fluid. This set us back a week and last Friday, I stopped by the local JD dealer and bought 5 1 gallon buckets of low-viscosity HyGard. I ended up buying some diesel fuel treatment from Amazon and putting that in the fuel tank and didn't bother draining it.
Thank you guys for all the comments and help. And one quick question, does anyone know what these two metal pieces go to? They came with the tractor in a bin of screws and bolts.
And one last question, does anyone know or can recommend a place where I can get a replacement front grill? The OEM one is simply out of my price range and the best I've found is around 350 after market.
Start up: I followed the operator's manual precisely and the engine fired up first time trying. A little bit of black smoke and that was it.
Power steering: Its great and I didn't anticipate how easy it would be to turn the steering wheel. My Cub Cadet zero turn is much more difficult to say the least.
Parking Brake: didn't think it worked but turned out it does just the lever doesn't move that far up.
Tachometer/Odometer: The tach isn't working and I'm pretty sure that the hour meter isn't as well. I'll have to look at fixing both in the future.
Loader: the loader works fine and is able to go up and down without any problems.
Hydraulic Lines: Surprisingly, no leaks on them which I was glad.
Front right tire: has a small hole in it that needs plugged. I'll get to this weekend.
Fuel tank: I knew I had to replace it going in and when I bought it, it came with a new one. The old one leaks pretty badly if filled to high. I'll hope to fix this by weeks end. The previous owner said that he ran out of gas one time and had to re-prime the fuel system which was pretty time consuming and painful. I'm hoping it won't be that bad.
Fuel pump: I noticed a little bit of fuel dripping from the line or the pump, not sure. I might buy a new clamp and see if that fixes it.
We didn't end up using the left over HyGard on the tractor because it looked like it had been previously opened and weren't really sure if it was hydraulic fluid. This set us back a week and last Friday, I stopped by the local JD dealer and bought 5 1 gallon buckets of low-viscosity HyGard. I ended up buying some diesel fuel treatment from Amazon and putting that in the fuel tank and didn't bother draining it.
Thank you guys for all the comments and help. And one quick question, does anyone know what these two metal pieces go to? They came with the tractor in a bin of screws and bolts.
And one last question, does anyone know or can recommend a place where I can get a replacement front grill? The OEM one is simply out of my price range and the best I've found is around 350 after market.
Last edited:
Spanner
Veteran Member
I'm glad we could be of some help. Well done. Have fun. :drink:
I don't recognise those plates. They look like shims or spacers for something else. :confused3:
I don't recognise those plates. They look like shims or spacers for something else. :confused3:
