John Deere 4310 codes

   / John Deere 4310 codes #1  

tomdelong

New member
Joined
Jan 3, 2012
Messages
6
Am getting a long followed by 3 shorts code > What does this mean? Tractor won't move forward or back. Lifts front and back work.
 
   / John Deere 4310 codes #2  
The codes that show with the long (2 seconds) followed by three shorts (and then either followed by another single short or two shorts) but you don't mention what follows after the 3 shorts. Can you reply with that answer and what is your 4310... forward/reverser or other?

From the tech manual that covers the 4310, the following from the code chart. tried to type it out, but lose the symbology. Code 31 is a 2 sec. long, followed by 3 shorts, followed by on short. Code 32 ends with two shorts.

31 -/---/- //Machine does not drive // Inch pedal potentiometer is out of range on the low end. Clutch Position Potentiometer Adjust clutch position potentiometer to within specification.
See ePowrReverser Potentiometer Calibration.

32 -/---/-- //Machine does not drive // Inch pedal potentiometer is out of range on the high end. Clutch Position Potentiometer Adjust clutch position potentiometer to within specification.
See ePowrReverser Potentiometer Calibration.
 
Last edited:
   / John Deere 4310 codes
  • Thread Starter
#3  
The codes that show with the long (2 seconds) followed by three shorts (and then either followed by another single short or two shorts) but you don't mention what follows after the 3 shorts. Can you reply with that answer and what is your 4310... forward/reverser or other?

From the tech manual that covers the 4310, the following from the code chart. tried to type it out, but lose the symbology. Code 31 is a 2 sec. long, followed by 3 shorts, followed by on short. Code 32 ends with two shorts.

31 -/---/- //Machine does not drive // Inch pedal potentiometer is out of range on the low end. Clutch Position Potentiometer Adjust clutch position potentiometer to within specification.
See ePowrReverser Potentiometer Calibration.

32 -/---/-- //Machine does not drive // Inch pedal potentiometer is out of range on the high end. Clutch Position Potentiometer Adjust clutch position potentiometer to within specification.
See ePowrReverser Potentiometer Calibration.

Didn't notice anything after the 3 shorts. My 4310 is the E-hydro Is the calibration routine fairly complicated? Did notice the tractor continued to roll forward or back after I let off the pedals ? Thanks Tom
 
   / John Deere 4310 codes #4  
I'll look again to see if the e-hydro has codes.

Ok, found it under e-hydro.

The long, three shorts has to do with forward reverse pedals.
Controller receives a command from both pedals at the same time.

Goes on to say.
Error status will reset when both pedal commands return to zero.

So look at a reason one or the other pedal is not returning to neutral position. Snow? debris?

Says there is no adjustment.. just that they need to return to home.
 
   / John Deere 4310 codes
  • Thread Starter
#5  
Thanks much. I'll check it out after our big snow. Thanks again!
 

Tractor & Equipment Auctions

120in Fork Extensions (A49346)
120in Fork...
2015 Ford F-550 Enclosed Service Truck (A46683)
2015 Ford F-550...
2018 Chevrolet Silverado 1500 4x4 Crew Cab Pickup Truck (A46684)
2018 Chevrolet...
2019 FREIGHTLINER CASCADIA TANDEM AXLE SLEEPER (A45678)
2019 FREIGHTLINER...
2007 Lexus ES 350 Sedan (A46684)
2007 Lexus ES 350...
2007 Ford E-350 Cargo Van (A48081)
2007 Ford E-350...
 
Top