Just another junk chainsaw

[xyz123]

Nice, we have our share of monster bucks around. I meat hunt more than horns but take my share.

I am meat too. But dad and brother go for racks first and meat deer for the jerky etc too.

They took several doe last year dont recall a buck from them.

My north place gets all kinds of nice ones too. More then south right now.

So many does too. I wish the guys paying to hunt the farmers lands around me would bust some does too.

 

[xyz123]

This pic I found funny and show you my flat north land.

 

[Eagle1]

I enjoy hunting and living in the hills, except when we get a nasty flash flood. We had two in 3 days this month. Will take months to put all the rock and clay back in places I need it. Flood overflow on the dam, when the 30' spillway becomes overwhelmed.

 

[xyz123]

Dad and brother have a creek that runs along the frontage of of the farm we bought up back in 94. Been known to flash flood and give them a scare.
I bought 2 places and they both bought 1 side by side.

Dad takes the tractor down in the creek to remove the gravel washed in and tree stuff that blocks up entry ends sometimes.

 

[xyz123]

It has been known to get up to the old oak barn built with no power tools.

Dad's barn from rough sawn oak. The other end that was added, has boards from my land rough sawn poplar that is turning too. Used to keep implements etc in.

 

[Eagle1]

Here is my creek coming in with normal flow (small channel) in back are the four 4' culverts under the drive.

 

[Eagle1]

Pond from the east

From the North

 

[Eagle1]

Washout debris field after a few days of work to gain access

From top of dam, hole I need to fix. Considering dropping an old parts truck in the as fill.

Back of dam

Creek bed below dam

 

[Eagle1]

Upstream hay and cattle fields. Next house is 1.5 miles or so from here. It all drains into this pond.

My walk over bridge that was under water.....

 

[Eagle1]

Just grins my cattle up on the ridge field 300' higher than the pond. Had to distract them, lead cow wants to go back free range on the front field, not fenced so I have to supervise..... not today.

and deer from last season

 

[xyz123]

Here is my creek coming in with normal flow (small channel) in back are the four 4' culverts under the drive.
View attachment 5357765
View attachment 5357766

Dad needed 2 for his.

Brother FEMA paid for a monster concert one for him. That thing today is way up there. Because dad priced one for his place.

 

[xyz123]

Well 346 OE arrived. I guessed right on being a 2003 or older. Is a 2001.

Suppose to be a 42mm p+c. But the used set I looked at was a aftermarket NE 44.3mm set.

The pistons that were bought for it by past owner was 42 44 45 why they wouldnt work.

Then there is this 45mm 353 afm set too.

Still has the plastic clamp that was prone to warp. Which I will cut off like the last one and clamp to boot with metal one.


Thanks again to the member here that offered me a chance to save another one.

Nice to know there are good folk here still as it makes up for the rotten egg.

 

[xyz123]

Just grins my cattle up on the ridge field 300' higher than the pond. Had to distract them, lead cow wants to go back free range on the front field, not fenced so I have to supervise..... not today.
View attachment 5357780
and deer from last season
View attachment 5357781

Nice. Going by your location under you name. Thats about 4hrs and some change where I was born in SW KY.

My cousin leases hunts on his farm land as there is some great deer in that area.



This guy stayed a basic 8 his whole life. Watched him fro a spindley 8 ear wide. Figured 2.5 when small.

Still see some of his genes today.

 

[xyz123]

I think I am going to try the 45mm afm set first to try it. Just because made like the oem 44.3 and afm 44.3 too.

 

[xyz123]

Dont see many of these at my local area FS.

Only guy I know with several of them lives about a hour or so west from me.

Mac 125 with a 101.

 

[xyz123]

What a day. Pulling a case half for one guy to ship for a 3300 and another text me needing oem seals for a PP380.

Down to only 7 oem NLA seals now.

Then 2 pto seals NLA for the 475 415 2077.

Was using dad ole 3300 to compare to make sure.

 

[xyz123]

Boney fingers again today for what. Oh ya I am retired.