Kubota F series

[arto98607]

I used to have the same problem - no loader!

 

[Barnbuilder]

Messicks has 3 used F series available. Anyone close to them been by and seen those machines?

 

[aczlan]

Messicks has 3 used F series available. Anyone close to them been by and seen those machines?

JOHNTHOMAS probbaly owned one of them at some point and traded it in

Aaron Z

 

[JOHNTHOMAS]

JOHNTHOMAS probbaly owned one of them at some point and traded it in

Aaron Z

I was going to say "No" because I bought my original F2680e first one back (Mowed with it yesterday) from Barlows but I sold my second one a F3080 to a man in NC so.... :confused3:
Barlows had a used one a couple of weeks ago on his lot and I ask ed him about it and he said it was already sold.

 

[ATRF]

I was going to say "No" because I bought my original F2680e first one back (Mowed with it yesterday) from Barlows but I sold my second one a F3080 to a man in NC so.... :confused3:
Barlows had a used one a couple of weeks ago on his lot and I ask ed him about it and he said it was already sold.

I'm new to this forum, so I apologise if this question has been asked already. I'm from the UK and have a five-year-old F3680 with 72in front mulching deck. Looking at it from the operator's seat, the left-hand side of the deck seems to cut a little lower than the right-hand side, and the deck doesn't lift evenly either. Any ideas? I'm wondering if I should replace the black bushes on the rear lift rods, as these look worn.

 

[JOHNTHOMAS]

I'm new to this forum, so I apologise if this question has been asked already. I'm from the UK and have a five-year-old F3680 with 72in front mulching deck. Looking at it from the operator's seat, the left-hand side of the deck seems to cut a little lower than the right-hand side, and the deck doesn't lift evenly either. Any ideas? I'm wondering if I should replace the black bushes on the rear lift rods, as these look worn.

The front wheels have settings so make sure they both are set in the same slot/hole and there is also the adjustment on the back of the deck (I think) so adjust those to the same setting on both sides. Your owners manual will cover this to to help you do your adjustments.

 

[aczlan]

I'm new to this forum, so I apologise if this question has been asked already. I'm from the UK and have a five-year-old F3680 with 72in front mulching deck. Looking at it from the operator's seat, the left-hand side of the deck seems to cut a little lower than the right-hand side, and the deck doesn't lift evenly either. Any ideas? I'm wondering if I should replace the black bushes on the rear lift rods, as these look worn.

First, check your front tire pressures. If they are different, you wont get an even cut. After that, there should be an adjustment to lift/lower each side so you can level the deck.

Aaron Z

 

[aczlan]

Your owners manual will cover this to to help you do your adjustments.

If you don't have an owners manual. here is a link to the manual for the Australian version of that mower: http://www.kubota.com.au/media/2188/agopsf2880f368001.pdf
It looks like the section labeled "MOUNTING THE MOWER" has a picture of the adjuster that you can use to level the deck L/R.
Also, the workshop manual: http://www.kubota.cz/data/manualy/f-80-wsm-en.pdf

Aaron Z

 

[ATRF]

If you don't have an owners manual. here is a link to the manual for the Australian version of that mower: http://www.kubota.com.au/media/2188/agopsf2880f368001.pdf
It looks like the section labeled "MOUNTING THE MOWER" has a picture of the adjuster that you can use to level the deck L/R.
Also, the workshop manual: http://www.kubota.cz/data/manualy/f-80-wsm-en.pdf

Aaron Z

Thanks to you and JT for the advice.

 

[Sigarms]

John, your old 3080 is still in my shed. Over 200 hrs on it now.

My old volkswagon had 360k on it when it finally died, and my current avalon just hit 300k, and I still have my old 25hp country clipper mower with over 1000 hours on it.

Point being I don't think your old F3080 is ever leaving NC LOL