I've had problems with small branches/twigs getting jammed in places that prevent things from moving properly, last time being the PTO lever. You might try looking really good under there with a light for anything wedged in the linkage. I have a B2710 and have read a lot about this kind of problem with pedal but have never experienced it myself. I grease the pedal every time I do the FEL, figure that can't hurt.
Kubota, first problem
- Thread starter Art Olive
- Start date
- Views: 14264
crbr
Veteran Member
Yes Sir.
crbr
Veteran Member
Replacement seems reasonably logical.
I had this problem with my B2620. Lubricating helped for awhile but then even lubing and moving the pedal back and forth would not help. I got stuck in the woods one day in the snow and the tractor would not start even fiddling with the peddle. I stuck a shim between the switch plunger and the tube(see pic in a previous post) and drove back to the Ponderosa.
The solution for me was to adjust that big nut on the switch (shown in a previous post with labeled adjusting nut)) moving the whole switch forward in the bracket and taking out the excessive play. No problem since. The worst part was having to take off a loaded tire on my model to get an open end wrench that large and long in there. You can test by turning on the key (don't go to start) and moving the HST pedal by hand (don't sit on the sit). You should hear a relay click as you push the pedal forward or backward and another click as it comes back to the neutral position. The clicks are slightly delayed so wait for them.
Hope this is relevant and helps. It's really quite simple and you don't need to bypass the switches, jumper things, get a new part. I can't believe the Kubota mechanics didn't know the solution unless I'm missing something. What is it with dealers - they always want to sell you a new part for something.
The solution for me was to adjust that big nut on the switch (shown in a previous post with labeled adjusting nut)) moving the whole switch forward in the bracket and taking out the excessive play. No problem since. The worst part was having to take off a loaded tire on my model to get an open end wrench that large and long in there. You can test by turning on the key (don't go to start) and moving the HST pedal by hand (don't sit on the sit). You should hear a relay click as you push the pedal forward or backward and another click as it comes back to the neutral position. The clicks are slightly delayed so wait for them.
Hope this is relevant and helps. It's really quite simple and you don't need to bypass the switches, jumper things, get a new part. I can't believe the Kubota mechanics didn't know the solution unless I'm missing something. What is it with dealers - they always want to sell you a new part for something.
Last edited:
rswyan
Super Star Member
- Joined
- May 12, 2004
- Messages
- 13,214
- Location
- Northeast Ohio
- Tractor
- Kubota B2910, Cub Cadet Pro Z 154S, Simplicity 18 CFC, Cub Cadet 782
taborekle
Gold Member
I was looking at a shop manual for the BX, and one of the 500hr (?) maintenance items was to measure and adjust the HST pedal travel, and it had a fairly small tolerance. Don't know if that has any relationship to your tractor, but it does make me wonder.
Also, on mine, I picked up a stick in the under deck assembly and that disabled me. So to those that suggested these two courses of action, I would ditto that.
Also, on mine, I picked up a stick in the under deck assembly and that disabled me. So to those that suggested these two courses of action, I would ditto that.
Another thing to check if the pedal is not coming back to neutral and thus not tripping the relay - then you may need to grease the pedal or use a lighter grease. The fitting is not easy to see, at least on mine and there are two fittings there - one for the brake pedal and one for the HST pedal further back in behind it. My manual only showed the brake pedal fitting and does not even tell you about the HST pedal zerk thus I did not grease the HST pedal for a long time.
If the HST pedal is coming back to the neutral position ok but the relay for restarting is not tripping then you need to adjust the switch as I explained before.
If the HST pedal is coming back to the neutral position ok but the relay for restarting is not tripping then you need to adjust the switch as I explained before.
herringchoker
Platinum Member
bstrom may be on the right track. That's what happened to my B7800 when I originally posted those two pictures: the adjusting nut had loosened, allowing the switch to back off so that the plunger wasn't pushing far enough on the switch to close the circuit. And yup, it's a really awkward thing to get at with a big wrench, even after removing the wheel.
Thank you - I thought maybe I was being ignored. Glad someone else figured out the most likely correct solution as well. That's what adjustment nuts are for, to adjust when there is wear over time or in your case it just loosened up and the switch was probably slopping around and the plunger not getting depressed correctly when the pedal came back to neutral.
HST Pedal Problem
Thanks to all who posted on my Kubota problem. I was following up on the spraying and greasing suggestion, when I observed how the lockout switch was activated. Namely, there is a plunger rod coming from the the rocker pedal and going thru a locator tube to hit the switch plunger. I could not see it before because the damper was in the way. I greased the rod where it goes into the tube and this seems to have solved the problem. Apparently the rod was sticking in the tube and preventing the pedal from going back to neutral. By the way on my 7800 only the rocker pedal has a grease fitting and I have been greasing it. Have not put the damper back and the tractor operates fine without it, except that if you release the pedal quickly the tractor stops with a lurch. Thanks again, Art
Thanks to all who posted on my Kubota problem. I was following up on the spraying and greasing suggestion, when I observed how the lockout switch was activated. Namely, there is a plunger rod coming from the the rocker pedal and going thru a locator tube to hit the switch plunger. I could not see it before because the damper was in the way. I greased the rod where it goes into the tube and this seems to have solved the problem. Apparently the rod was sticking in the tube and preventing the pedal from going back to neutral. By the way on my 7800 only the rocker pedal has a grease fitting and I have been greasing it. Have not put the damper back and the tractor operates fine without it, except that if you release the pedal quickly the tractor stops with a lurch. Thanks again, Art
