MossRoad
Super Moderator
- Joined
- Aug 31, 2001
- Messages
- 58,383
- Location
- South Bend, Indiana (near)
- Tractor
- Power Trac PT425 2001 Model Year
Here's the tread on mine. Just for comparison.
Leaking wheel motor
- Thread starter davesisk
- Start date
- Views: 5445
bmac
Veteran Member
OK, now I think you're mocking me. /forums/images/graemlins/confused.gif /forums/images/graemlins/grin.gif
I talked to Terry. He said best bet is to pull the wheel motor off and send it to them to rebuild, should run around $120. I new wheel motor would run around $500. He said I could probably install the seal kit myself, but they have the means to pressure test it afterwards.
I took it to a local Briggs and Stratton repair shop that also rents and repairs Toro Dingo's (ie. they were quite familiar with a very mechanically similar piece of equipment). Even with that, I still think I financed some of their Power-trac education. I think I'll take the route that I know will work: shipping it to PT for a rebuild!
Dave
I took it to a local Briggs and Stratton repair shop that also rents and repairs Toro Dingo's (ie. they were quite familiar with a very mechanically similar piece of equipment). Even with that, I still think I financed some of their Power-trac education. I think I'll take the route that I know will work: shipping it to PT for a rebuild!
Dave
Charlie_Iliff
Veteran Member
- Joined
- Jun 13, 2001
- Messages
- 1,890
- Location
- Arnold, MD
- Tractor
- Power Trac PT1845, John Deere 2240, John Deere 950, John Deere 755, Jacobsen Turf Cat II
<font color="red"> I think I'll take the route that I know will work: shipping it to PT for a rebuild!
</font>
There's always the other proven alternative. Buy a 55 gal. drum of 10W40 -- and maybe a bucket of oil dry and a broom. /forums/images/graemlins/laugh.gif /forums/images/graemlins/laugh.gif /forums/images/graemlins/grin.gif
</font>
There's always the other proven alternative. Buy a 55 gal. drum of 10W40 -- and maybe a bucket of oil dry and a broom. /forums/images/graemlins/laugh.gif /forums/images/graemlins/laugh.gif /forums/images/graemlins/grin.gif
MossRoad
Super Moderator
- Joined
- Aug 31, 2001
- Messages
- 58,383
- Location
- South Bend, Indiana (near)
- Tractor
- Power Trac PT425 2001 Model Year
Here's Charlie's tread, too /forums/images/graemlins/grin.gif /forums/images/graemlins/tongue.gif
bmac
Veteran Member
You've crossed the line with this one. /forums/images/graemlins/grin.gif
MossRoad
Super Moderator
- Joined
- Aug 31, 2001
- Messages
- 58,383
- Location
- South Bend, Indiana (near)
- Tractor
- Power Trac PT425 2001 Model Year
And don't forget yours either! (hee hee hee, this is fun)
Click here! (I didn't want to post any more in-line images, out of respect for those of us with dial up connections(me)).
Click here! (I didn't want to post any more in-line images, out of respect for those of us with dial up connections(me)).
bmac
Veteran Member
You Win!
Charlie_Iliff
Veteran Member
- Joined
- Jun 13, 2001
- Messages
- 1,890
- Location
- Arnold, MD
- Tractor
- Power Trac PT1845, John Deere 2240, John Deere 950, John Deere 755, Jacobsen Turf Cat II
<font color="red"> is this sucker just wedged on there, or is there an additional fastener somewhere? </font>
There's always another bolt. /forums/images/graemlins/grin.gif
Heard about a guy once who used a cold chisel to take the head off an engine. Must have been the gasket cement, thought he, since he'd taken out all the head bolts -- except that one row. /forums/images/graemlins/tongue.gif
There's always another bolt. /forums/images/graemlins/grin.gif
Heard about a guy once who used a cold chisel to take the head off an engine. Must have been the gasket cement, thought he, since he'd taken out all the head bolts -- except that one row. /forums/images/graemlins/tongue.gif
