OP
Gregster613
Platinum Member
- Joined
- Apr 19, 2009
- Messages
- 825
- Tractor
- 273 TYM. 2009 //Yardmachines 7 Speed Shift-on-the-goScotts L2048
Thanks again for the help Dave! I found that info and particular page (#15) last night, filled out all that I was sure of (including wire control) and sent it out. I have a confirmation page back from them this morning.
The person I've been e-mailing per this order is the same person whom I originally connected with and provided me the schematic for my original TYM valve #11087-2S. I've said "repeatedly" that I want the same spec's as TYM uses and since this company built the valve initially for TYM they should have access to that info already. The only item I was concerned about was the power beyond valve because I was unsure if my old one would transfer over - which I believe will - then I see it is listed in the last block on page 15! As an HPC-fitting (Power Beyond). I got slightly stumped when he asked 'me" for numbers about the valve. Guess I was using wrong terminology.
On page 15 the only things I didn't know for sure how to answer was the spool type - so I asked for what I have now Raise/Lower = DA + float so in Section 1 I put code 3X. For curl/dump in section 2 they only had DA + regen w/metering [I assume this is the quick dump function?] they listed 8R and 8S but both say the same thing so I have 8R in my copy of the sheet but in my e-mail I said whatever TYM used is what I wanted. I put in all that I knew of and feel okay with what I ordered, specifically since I asked several time to have whatever spec's TYM uses. It should be pretty much a plug and play event once the valve actually gets here.
What did through me off for a while was the Series CV112 valve reference - my current valve is listed as 11087-2S and that's what is in the bottom right hand side of the schematic I was sent when I asked if they could replace my valve. All these different #'s and specific hydraulic speech kinda make me dizzy getting through this! But I will chug my way through and get a new valve eventually. I'm getting closer each time. Greg
The person I've been e-mailing per this order is the same person whom I originally connected with and provided me the schematic for my original TYM valve #11087-2S. I've said "repeatedly" that I want the same spec's as TYM uses and since this company built the valve initially for TYM they should have access to that info already. The only item I was concerned about was the power beyond valve because I was unsure if my old one would transfer over - which I believe will - then I see it is listed in the last block on page 15! As an HPC-fitting (Power Beyond). I got slightly stumped when he asked 'me" for numbers about the valve. Guess I was using wrong terminology.
On page 15 the only things I didn't know for sure how to answer was the spool type - so I asked for what I have now Raise/Lower = DA + float so in Section 1 I put code 3X. For curl/dump in section 2 they only had DA + regen w/metering [I assume this is the quick dump function?] they listed 8R and 8S but both say the same thing so I have 8R in my copy of the sheet but in my e-mail I said whatever TYM used is what I wanted. I put in all that I knew of and feel okay with what I ordered, specifically since I asked several time to have whatever spec's TYM uses. It should be pretty much a plug and play event once the valve actually gets here.
What did through me off for a while was the Series CV112 valve reference - my current valve is listed as 11087-2S and that's what is in the bottom right hand side of the schematic I was sent when I asked if they could replace my valve. All these different #'s and specific hydraulic speech kinda make me dizzy getting through this! But I will chug my way through and get a new valve eventually. I'm getting closer each time. Greg
