Welding Loader Mounts

   / Welding Loader Mounts #1  

F15DOWNER

Bronze Member
Joined
Sep 3, 2002
Messages
87
Location
Rome, Ohio
Tractor
Yanmar / F15D
I'm welding up some brackets for a loader and some people have told me that I have to be careful that I don't fry electrical components and arc the bearings in the motor.
Is there any truth to this?
I'm using an AC stick welder. My original plan was to tack them in place and remove them for most of the welding, keeping the ground close to where I'm welding.
I don't want to find out the hard way so I figured I would ask the experts.
(Most of the electrical components aren't cheap)

Tom
 
   / Welding Loader Mounts #2  
Keep the ground VERY close to where you are welding and only tack it in place. Don't do full welding!.

That said, I wouldn't do it. I used to be a maint tech at a forging plant and we would always take whatever we could off the press when possible to do repairs.

We did weld a lot of the repairs in place though and we had tens of thoudands of dollars in electronics on the presses. I can't think of a single time it fried something. That was on that companies property though, not my 5, 10, or 20 thousand dollar tractor.

Good luck
 
   / Welding Loader Mounts #3  
It is not a problem just attach your ground to the steel not the tractor. We have welded hundreds of brackets in place and have never had or seen one problem. If you hook the ground to the PTO shaft that might be a different story.

Buck
 
   / Welding Loader Mounts #4  
F15DOWNER:

Do we get pictures when your done installing? /forums/images/graemlins/grin.gif
 
   / Welding Loader Mounts #5  
These guys have it spot on. So long as the electrical system and bearings are not part of the circuit, then you won't have a problem. It's when you connect the ground to the battery terminal or the pto shaft that you'll run into problems. Besides, the ground won't work through a painted surface anyways.
 
   / Welding Loader Mounts
  • Thread Starter
#6  
As soon as I, get er done, I will post some pictures.
Thanks for the input!!!
Tom
 
   / Welding Loader Mounts
  • Thread Starter
#8  
Here you go Whiskey!

Don't laugh too hard at my welding.
 

Attachments

  • 837505-side.jpg
    837505-side.jpg
    89.3 KB · Views: 297
   / Welding Loader Mounts
  • Thread Starter
#9  
Mount
 

Attachments

  • 837508-bracket.jpg
    837508-bracket.jpg
    90.6 KB · Views: 286
   / Welding Loader Mounts
  • Thread Starter
#10  
Other Side
 

Attachments

  • 837509-exaust side.jpg
    837509-exaust side.jpg
    97 KB · Views: 267

Tractor & Equipment Auctions

HEAVYEQUIPMENT ROLLS OF CONDUIT (A50854)
HEAVYEQUIPMENT...
2019 Ford Fusion Sedan (A50324)
2019 Ford Fusion...
Neckover GL24-2-7K Gooseneck Trailer  24ft Deck, Dual 7K Axles, 14K GVWR (A51039)
Neckover GL24-2-7K...
4 1/2 150G DRILL STEM 358 JOINTS (A50854)
4 1/2 150G DRILL...
KODIAK 10' HD ROTARY MOWER (A51406)
KODIAK 10' HD...
WEATHERFORD MP-10 TRIPLEX MUD PUMP POWERED BY A CATERPILLAR 3412 ENGINE (A50854)
WEATHERFORD MP-10...
 
Top