Search results

I would say this is safety issue. So the operator doesn’t go too fast in reverse and lose control. Many ATVs use a reverse limiter.

Normal operation. 3rd range is actually a very high range to be doing any sort of actual work with. I get it you were trying to get there faster but you would be better to run 2 range and higher rpm when doing work. I usually only use 3rd range when I’m roading it.

Ok. If you had a cab I was going to tell you to watch seat back against rear glass.

Do you have an open station or cab?

Yes, that is where the female coupling goes to dump fluid back into the system. Not saying it won’t operate by going into one of the sets but the correct way is removing the plug and adding coupling. Use the hookup so the lever stays in position and doesn’t return to center. I think mine is on...

Ok. That’s what I was thinking. Should be fairly straight forward. Bolt subframe with braces. When you get it ready to go on the tractor just remember to not have your drawbar pin in or it won’t slide in.

Is the backhoe on a pallet? Do you have to lift the hoe to get to the subframe? Once you get the subframe bolted on you can hook up the hydraulic lines to lift and level the hoe for attaching.

Just unbolt the front bracket and install the new one. You won’t have any issues. Just to be sure I would measure the new bracket against the old just to make sure you have the correct one. What tractor model do you have?

I owned the same tractor before I traded for the new MT 3 series. Mine exhibited the same issues at around 1100 hrs. Dealer determined it was regen burner. They installed the injector kit. $2,600.00 parts and labor. Several hundred hours later it was doing the same thing again. It was either the...

Thanks Avenger! That’s what I was looking for.

Does anyone have the cross reference number for MT 3 series. Looking for wix number. I searched through the filter thread and on line but still couldn’t come up with one I am certain on. Thanks

My 2014 XR 4046 started doing the same thing about 300 hours after the new injector kit was installed. Either it was the injector kit again or the ECU. I didn't want to go through the hassle again so I traded for a new MT 357. Dealer gave me a good trade in amount and had what I wanted on the...

I was recently mowing then moving from one property to another and without warning heard a pop and the forward pedal went completely to the floor. Tractor stopped immediately. Crawled underneath to find one end of the hst linkage was broken off. I got a neighbor to pull me back to my building...

The dealer should have also given you the original front cross member bracket that is changed out to the cross member to accept the front of the backhoe subframe. It is painted blue. I would hang on to both of those parts.

A little advise when hooking up the backhoe. Before backing up to engage the subframe remove the pin holding the drawbar because the pin hanging down will not let the subframe enter the slot. Remember to put it back or just remove pin and drawbar all together when using the hoe.

The black part is changed out with the blue part when you have a backhoe. The blue part allows the subframe to attach. The dealer wanted it to stay with the tractor in the event you would ever get rid of the hoe you could put it back on.

Just to clarify the dealer called it a burner kit. Took about 6 hours for them to install.

It may be the burner. I have a 2014 4046XR and had to have mine replaced. Same symptoms. Unfortunately it cost about $2400 installed. I was out of warranty.

Dealer came yesterday and put his gauges on the AC. We ran it for quite a while and the light never blinked once. The outside temperature was only around 66, much cooler than the 84 degree day when the issue occurred. The pressure readings were pretty much normal or if anything maybe a touch...

Thanks Dude. I think you are correct. The owners manual didn't have anything. I'll post what the dealer finds. Thanks to all again.

Yes, that is correct. The problem is when the light blinks the compressor clutch is cycling on and off. Can't be good on the new compressor. I talked to the dealer shortly after posting. They think it may be over charged or since the temperature has gotten much warmer the possibility of...

Has anyone ever had the amber light on the AC push button slow flash? Last fall the original compressor failed and the dealer replaced it a few weeks ago. After running the AC for a while every so often the amber light will slowly blink for a while. Air seems to remain cold. Nothing in the book...

I replaced mine about 2 1/2 years ago. Had a slow seep somewhere in the core. If I remember correctly is was slightly over $100. Had a local shop make a short jumper hose so I could still move it around until the new cooler came in. Simple change out.

Has anyone replaced the battery on their XR yet? Curious if you went through LS or replaced with an aftermarket. The size appears to be critical due to how its mounted. Thanks.

For those with equipment or flat bed trailers that have treated wood decks what is the best coating you have found that holds up the longest? I've used a couple different brands but it doesn't seem to last too long. I know the sun and weather is hard on the deck. I finally can get mine out of...

I had an hydraulic line that comes from the pump fail due to it rubbing on the engine block. I had a new one made at my local NAPA. On my model it was located on the right side. Comes out of the pump and runs up to the fire wall behind the top of the engine. I had to remove the hood and the hood...

I know your tractor is the new 4100 series but I thought I would post of pick of my XR4046 with 4102 loader. I assume your tractor has the 4104 loader. It looks like the 4104 loader brackets are shaped differently than the 4102 brackets. This pic is with the tractor on a rise with the front axle...

I recently purchased an LS backhoe for my XR4046. I really like the subframe mount. I looked at 3pt. mounts but opted to go with the subframe. I think the LS subframe will be much easier to put on and take off. Not that I have much warranty left but I would check and see if a 3pt. would alter...

Does anyone know a ball park price for the LS Backhoe attachment for the 4000 series? If you own one are you happy with it and does it perform as you expected. Thanks in advance for any feed back.

As I approach my 500 hr. service as recommended per LS to change the hydraulic fluid (11.4 gallons) I checked into changing with Amsoil synthetic hydro fluid. I was shocked when 15 gallons with tax was over $720.00. Needless to say I'm not going that route. I'm sure it's a great fluid and am not...

Here is an image of the right brake light showing the cracks. The center is actually open. The left one also has spider web cracks. I would like to replace them with LED but can't seem to find 3 1/2". The way these are attached behind the fender may be more trouble than what it is worth. Can a...

I noticed my right side round break light has a crack in it. Doesn't look like anything hit it more like it may have got hot and became brittle. I was looking to order a replacement online. The lamp part # is 40261649. The LS parts site (Sundowner) is not very good imo. I entered the part number...

Many post a certain feature they would like to see on their tractor. I recently read a indicator light when the 4 wheel drive is engaged, a clock not on the stereo, etc. I would like to see a little larger fuel tank. Even though the tractor is fairly easy on fuel it would be nice to not have to...

http://https://nkleadershipwatch.wordpress.com/2016/05/14/kim-jong-un-visits-machinery-and-equipment-exhibition/

Fuel tank filler neck split for no apparent reason. Dealer has new tank ordered. I took a couple pics then rapped electrical tape around neck to keep debris out.

Does anyone know if the round red brake lights are a sealed unit or does it take a bulb? I haven't got a chance to look in the on line parts schematic yet. Thought maybe someone has replaced one and might know. I noticed right side out when parking brake is set. Not sure yet but it doesn't look...

Before and after adding slip clutch.

I recently bought a used 6' TSC rotary mower. Almost new condition. Guy only used it about 20hrs mowing down grass a couple times for a new home. It probably wouldn't be my first choice but I couldn't pass it up for 1/2 price. I'm only cutting pasture grass and very few small saplings so I...

I finished some mowing this morning and was stopped putting some concrete in the bucket when my wife walked over before she left for work. She found a bolt in the grass which appeared new and clean and definitely off my tractor. Metric with flat washer and lock washer. Looked like the same as...

Here's a pic. 130 hours. Good thing for warranty.

I was moving gravel today and noticed the inside front right tire was wet with oil. Appears the seal let go and puked out all the oil. Going to the dealer Monday or Tuesday. I saw another thread where a 7010 had a wheel bearing go out and lost all the oil. Hopefully not a lot of down time.

The top two pics are the right side. The bottom of the hood touches the rubber seal but seems to open up more toward the top. The left side is where the larger gap is. The bottom is approx. 1/2" away from the seal at the bottom and gets closer toward the top but is still away. I've exhausted...

I installed 4 new LED work lights. What a huge difference. I stayed with the oval design to look like factory. They are 1350 lumens each. I got them from Surplus Center for around $225 for all 4 shipped. The brand is Buyers which makes some very nice products.

I bought it for $1,050. I think new they sell for $1,500-$1,600. Several equivalent blades also run about that amount. I don't think I can get that much adjustment on the lower arm. Even if I could I wouldn't want to change that every time I used it. Here's what it looks like.

I found a used 8ft Bush Hog blade series 90. Some of the info I came up with shows the weight at approx. 740 lbs. I was really looking at the 7ft. figuring that would be plenty wide. Like the idea of the extra weight for better cutting in some of our hard soil. My question is do you think this...

Has anyone found a NAPA or after market cross reference number for the fuel pre-filter? I don't think I saw one listed in the filter thread. Thanks.

I posted this over in the Husqvarna forum but didn't get any response. Without buying Husqvarna orange spray paint does anyone know what color would be the closest match? AC orange, Kubota, New Kubota, Case orange? These colors are readily available. I have a Husqvarna rider I'm going to sell...

Getting ready to do my 50hr. service. Curious on what weight and brand oil others are using. Thanks.

Without buying Husky orange spray paint which color is a close match? AC Orange, Kubota, Case, New Kubota Orange?

A while back I was attempting to grease the FEL zerks that are recessed. I thought I was never going to get the grease gun off. I actually had to unscrew the end and took a small screw driver to get it to release. Anyone else have trouble with this? I looked at getting a Lock N Lube end for gun...

Any cab owners have any issue with their windshield wiper motor? I was using it a few times while pushing snow. I noticed it was stopped on the left hand side of the glass. I got out and moved the arm and it made a few passes then quit again. It makes a few cycles if you move the arm but won't...

You northeast guys all fueled up and got your blades and blowers on?

How much pressure are you running in your rear tires? I don't have any fluid yet but I noticed the tread or bars on rear tires are not fully contacting the ground. R4 industrial tires. I would think you would want the entire tread making contact. Thanks.

Having some issues on insuring my tractor. My insurance agent who we've had for 30 years said my home owners insurance company only want's to insure it for $10,000. He told them that was crazy because the tractor was valued at almost 3 times that amount. He's working with other companies but not...

Hey guys. Today I was pushing some snow with my XR4046hc. I put an Express Steel 7ft snow box on it. Very nice quality. At one point I noticed a red indicator in lower left corner of dash display. Looked like a circle with and exclamation point in it. It went off on it's own and never came on...

I read a couple threads on the cab radio speakers. I agree the sound is not good. I'm planning on replacing them with some better quality speakers. It sounds like the best approach is to take the cab top off. If you have replaced yours can you expand on how you went about it and if there is...

There is a switch on the dash on the right side above the throttle. What is this for? Momentary rocker with same symbol top and bottom. Bottom has a slash line through it. Forgot to mention the dealer forgot to give me the operators manual before I left the dealership so he is going to send it...

Hello, just signed up. This looks like the place to go for great advise. Recently took delivery of new XR4046HC. I'll be posting a few questions soon and getting my profile finished. Just wanted to stop in.