Degolyerent
Gold Member
- Joined
- Nov 21, 2010
- Messages
- 439
I have had a terrible time posting, it don't want to send , so I cancel and try to send shorter version later and both send. Go figure
locknlube cupler for a grease gun
- Thread starter johnems
- Start date
- Views: 123540
grsthegreat
Super Star Member
ok, today i spent 4-1/2 hours degreasing my loader. haha
Actually, while i had the loader off and i completed my 400 hour service, i decided to try and clean up the greasy mess that was my loader. I was actually getting big globs of grease falling onto my hood and hitting the windshield.
So today i pulled every single pivot pin and assorted parts, pressure washed all the parts and used wax to remove all the grease. Man, have i been overdoing it with the grease.
I also had to replace 2 zirks on the tractor that wouldnt even hold the new lockandlube grease tip. it just slipped off. i replaced them with new metric zirks,and all is good again.
From now on ill stick to a single shot of grease. I had to scrape gobs of the crap out of every port i could see.
It was a heck of alot of work, but since ive had the tractor for 3 years, i felt it was about time.
Now that the tractor is all waxed and so is the loader, the tractor looks better than the day it arrived here. I almost dont want to use it.
Actually, while i had the loader off and i completed my 400 hour service, i decided to try and clean up the greasy mess that was my loader. I was actually getting big globs of grease falling onto my hood and hitting the windshield.
So today i pulled every single pivot pin and assorted parts, pressure washed all the parts and used wax to remove all the grease. Man, have i been overdoing it with the grease.
I also had to replace 2 zirks on the tractor that wouldnt even hold the new lockandlube grease tip. it just slipped off. i replaced them with new metric zirks,and all is good again.
From now on ill stick to a single shot of grease. I had to scrape gobs of the crap out of every port i could see.
It was a heck of alot of work, but since ive had the tractor for 3 years, i felt it was about time.
Now that the tractor is all waxed and so is the loader, the tractor looks better than the day it arrived here. I almost dont want to use it.
Sodo
Elite Member
- Joined
- Apr 21, 2012
- Messages
- 3,300
- Location
- Cascade Mtns of WA state
- Tractor
- Kubota B-series & Mini Excavator
These are so great, I think I'll order some for Xmas presents. I wish it was a little smaller though.
bumperm
Veteran Member
That's T-W-E-R-K-I-N-G . . . twerking is fun . . . how many times do I have to tell you? :c)
bumper
Mud Mechanik
Gold Member
Just ordered my Lock and Lube...can't wait to try it, if this many folks like it.:cool2:
That is an great idea! I think I'll order some for presents as well!
FatTire
Veteran Member
- Joined
- Oct 2, 2007
- Messages
- 1,369
- Location
- Colorado
- Tractor
- Kubota L5740, Unimog 404 w/ snowblower, Deere 620i UTV, MX5100 (sold)
I see from the tracking info my lock-n-lube should be here today or tomorrow. I bought an extra to give a friend who I owe a favor.
grsthegreat -- Now you did it, as soon as I get time I'm going to have to do a clean up. Your machine looks great.
grsthegreat -- Now you did it, as soon as I get time I'm going to have to do a clean up. Your machine looks great.
davrow
Veteran Member
Okay... I have a CK27. Anyone else notice this? LOTS of the zerks are in the recessed fittings. I was about to plop down my money - this is the only negative I have heard on this device.
dragoneggs
Super Star Member
- Joined
- Jun 9, 2013
- Messages
- 13,627
- Location
- Seabeck, Washington
- Tractor
- Kubota BX-25D, Kubota Z122RKW-42
Hmmm... too bad on the CK but on my BX the recess fittings on the BH have enough clearance around to allow access. What a dream! :cool2:
brain55
Veteran Member
The only machine I've run across since I've had mine, with recessed fittings that I couldn't use it on, was the bucket pins on a Takeuchi TB-15 excavator.
Brian
Brian
