Tractor News Row Crop vs Utility

[Creamer]

It's a pretty broad term that just says the tractor is equipped to handle "row crop" farming. Corn, sugar beets, etc, they are planted at specific row widths and the machines that care for the crop need to be able to drive between and above the rows and in many cases they need to do it many times. It kind of depends what vintage machine you are looking at. Many people will only consider a tractor a row crop tractor if it has the following; Tread width adjustments and machine height to drive between the rows, 3 point hitch, & either a closed center hydraulic system or the more current pressure and flow compensated open center systems. As many time the implement used require the operation of more that one hyd motor that basic open center systems, or even pressure compensated systems do poorly if at all.

You are pretty modern in your description. There have probably been more row crop tractors built without 3 pt than with when you think of all the Farmalls (F-series, A, B, C, H, M, 300, 400, 350, 450, etc.) as well as Deeres, Cases, Minneapolis Molines, Coops, Cockshutts, Olivers, Allis Chalmers, Porshces, Massey Harris, etc. that were built until the late 50s. Of course back then it took a lot more tractors than it does now because they were not quite as powerful. Hydraulics were not a lot of consideration these models either, if they had hydraulics they were typically single action with the sole purpose to lift the machine.

 

[TJP89]

You are pretty modern in your description. There have probably been more row crop tractors built without 3 pt than with when you think of all the Farmalls (F-series, A, B, C, H, M, 300, 400, 350, 450, etc.) as well as Deeres, Cases, Minneapolis Molines, Coops, Cockshutts, Olivers, Allis Chalmers, Porshces, Massey Harris, etc. that were built until the late 50s. Of course back then it took a lot more tractors than it does now because they were not quite as powerful. Hydraulics were not a lot of consideration these models either, if they had hydraulics they were typically single action with the sole purpose to lift the machine.

I see a confusion here between newer and older row crop tractors. I have a row crop tractor in my barn. It is a 1950s Farmall H, tricycle front end, one way hydraulic pump, over 2 ft clearance. It currently has a belly mower and an aftermarket 3PTH (though I do have the swinging drawbar). Not exactly a modern farming machine. My Kioti, a CUT, would outperform it in everything save ground clearance and maybe straight pulling power. What went as a row crop back then (when the modern CUT didn't exist) is much different than what a row crop tractor is now. However, there is a fuzzy line between high HP utility and a row crop. I think any tractor with more than about 125HP is capable of modern field work. I have also seen my neighbor use his 220HP JD row crop (It's his primary farm tractor) with a front plow to clear the road of 2ft of snow, so its a very fuzzy line.

 

[Creamer]

Are there any 100 Hp+ tractors built today that are not row crop unless they are built as backhoes? For that matter has there ever been a 100 Hp+ tractor that was not a row crop and not a specific built backhoe? I can't think of any unless you want to somehow count one of those massive steam engines that would pull a 6+ bottom plow. I guess we also probably need to exclude crawler or tracked tractors.

 

[DFB]

Lots of options available today, each for a specific need...high wheel, narrow, low profile etc.

 

[MHarryE]

Not sure about others but John Deere's 6130M is 130 HP utility.

 

[CalG]

If a "row crop" machine were not identified by adjustable track width and implement mounting pads all around, I will be at a loss for what would set it apart.

I never thought about the big wheels, they all had them.

The Ford N's were chore tractors. They had nothing but a pto and a draw bar, Handy size though, even for a boy. ;-)

 

[RedNeckRacin]

Are there any 100 Hp+ tractors built today that are not row crop unless they are built as backhoes? For that matter has there ever been a 100 Hp+ tractor that was not a row crop and not a specific built backhoe? I can't think of any unless you want to somehow count one of those massive steam engines that would pull a 6+ bottom plow. I guess we also probably need to exclude crawler or tracked tractors.

The JD 5E, 5M, 6D, and 6M models are utility tractors all with 100hp+ options.

 

[Creamer]

The JD 5E, 5M, 6D, and 6M models are utility tractors all with 100hp+ options.

Per the JD site the 6D qualify with 105-140 Hp models. The 6M are not considered utility. The 5 series only goes to 100 Hp. I had missed the 6D series.

 

[Gary Fowler]

To be a true row crop tractor the tread must be infinitely adjustable and this is usually accomplished by sliding the wheel hub on an extended axle shaft. The shaft could be long enough to mount a dual tire on each side and have enough room between the duals for a center to center dimension to be up to 40" or more so that each tire is running in the middle of two rows.

Other than that, they are pretty much the same as all other tractors of similar size. Clearance may be a bit more than a CUT but only because it has larger and taller tires. The drive train ( engine, transmission, rear end and front drive if 4WD) are still configured in most cases exactly like a CUT or Utility with the front axle pinned directly to the drive train with swivel pin holding the front axle. They rarely need to have more than 24" of ground clearance for any crops raised. When they get too big for the tractor to pass over, the crops are considered "laid by" and then just waiting for them to mature for harvest.

On my utility tractor, I can only adjust the tread width by moving the inner rims around on the outer mounting Z points. This give me about 4" of adjustment wider or narrower with the inner cup setting out. I don't think I could even mount the tire with the cup in as the tire would hit the fenders. ON many CUT tractor the rims, have welded one piece rims so there is no other setting, the only adjustment is Wide or Narrow accomplished by flipping the rim so the cup is out or in.

There are high clearance rigs for spraying pesticides and herbicides that may have as much as 6 feet of clearance but they aren't considered tractors.

 

[RedNeckRacin]

Per the JD site the 6D qualify with 105-140 Hp models. The 6M are not considered utility. The 5 series only goes to 100 Hp. I had missed the 6D series.

Check your info. Snapshot of the JD site today. These are all listed as utilities on JD's own website. Thanks though! :thumbsup: