Search results

I recently bought a used TC40D with under 700 hours as an modest upgrade from my trusty TC33D.... Everything is tight and functioning except my flashers and turn signals. I've read a few of the posts here and I guess I'll have to crack the dash to check the fuse. For some reason, I suspect it...

Unfortunately, I'll be replacing my water pump tomorrow on my TC33D - it was my fault for forcing a belt on that was toooo tight and it was too much for the bearing.. Anyway, I don't have a service manual to give me the torque settings or tightening sequence if they have it and wondered if...

Got the new oil filters from Hoye yesterday and went out to change the oil but have no idea how to get the old oil filter off as there is a factory bracket flush against the back of it. Is there a simple way around this that I'm overlooking? Looks like there is also a drain plug for the...

took a look at a 2210 today with powershift. Tractor has been sitting a bunch. Motor is good and strong, no leaks sounds great. Drivetrain and 3pt are acting up. 3pt doesn't function no lift or drop. Owner has it chained up. Put it in gear and release the clutch and you can feel it try...

I've got a 58 841 Powermaster with lots of family history. Unfortunately, It's been sitting in my shed for a couple of years - turns over but I think the tank will need some TLC. Anyway, I rebuilt and repainted it back in the late 1980's and thought I would maybe go at it again but I've been...

I've got a 2004 ZForce mower - this year I replaced the front tires with never flats and had tubes on the back tires - thinking I'm good but ran over a broken bottle mowing and a I'm rewarded with a flat back tire. Tire size is 18x9.5-8. The old tire is dry-rotted and I was too tired to...

My 7308 bucket on my TC33D is rusting thru due to too many loads of horse manure I suspect - in looking on-line I see plenty of buckets with the universal bracket but does anyone know where or who might have a bucket with the OEM brackets? Thanks in advance for any help!

Took off my dash to change out the flasher module but the retainer nuts that were in the fiberglass cracked off on both sides - I guess it's age or something.. any idea how to repair it or find a auto clip that might hold it in tighter? It sits ok without falling out but I need to fix it but...

Pretty unique find at the market today - couldn't pass it up and the good news is it will fit in the shed.. The detail on it is pretty interesting when you take a close look. Anyway, thought you guys would enjoy more than most others.... I'm assuming its a ford...

Took my old 841 out to cut grass with a 6 ft bush hog for the first time. Great power, much faster than my little 4 ft Yanmar combo but the 3pt kept dropping. It will go from ok height to touching ground in about 45 seconds. It is a little slow to lift also - depends on RPM. Any ideas...

I've read some posts about the 2-pin aux plugs but I think mine is backwards for some reason - it works when the ignition switch is off but it dead when the switch is on with the engine running. From what I've read, this is the opposite of what it should be doing - any ideas? Thanks

Have a 1500 that sits quite a bit - started it a month or so ago with no problem. Today I turned the switch and nothing. No click, not try to turn slow just nothing. Battery is charged (Optima), tried to jump as well with my other tractor, nothing. Headlights come on bright but when I turn the...

My 1500 was running in neutral for about 5 minutes(sitting by itself) when it just kicked into gear. Thankfully the brush hog was on it and in the down position so the left wheel just dug itself into a hole in the soft Florida sand.. Whatever caused it now has something locked up - the only...

I've had my 1500 for about 6 months, put about 40 hours on it, and yesterday my wife says "did you change the oil in the tractor because it's leaking" Where's the logic in that?? Anyway, I didn't change the oil but it is leaking... Obviously, it had not before. There's a small hole that is on...

Well here's what happens when you get a little too confident after installing an over run clutch.. Hit a 6" pine and crack! The weight actually has lead blocks molded into it and it broke right next to them. Any ideas on a better system?

My first post - been reading this board for a while - hope you can help.... I've got a red Yanmar 1500 and today I noticed the bulb in the bliner on the fender had fallen out of the socket - I put it back in and checked it - no go.. wiggled the wire going into the plug and got a little spark...