Search results

It is probably your ignition switch. They are notorious for causing issues. Mine did the same thing. I sprayed some fluid film in it and worked it back and forth a bunch, and it's good for now. I'll have to pull my cab to replace it.

Purchased the cylinder, you can find it at surplus center item number: 9-12228-4

Got my front chute deflector all installed. I used hoses with built-in swivel ends so the hoses wouldn't twist. It looks like I will get to put it all to the test this week with another spring storm with 12-18" on the way!!

As a price point I bought a used 2015 cs2410 200 hrs with loader, factory cab, 60in mid deck, and a 50in front blower. The only thing that had been used was the front blower, doesn't look like the loader or mower had ever been used. This was at a dealer and was traded in on a new Kioti cx2510. I...

Front spacers actually harm your turning geometry and put more load on the stub spindle. I would stay away they are not needed.

Great find. The serial # starts with F so it is a 2006 model year.

Thats an older DK series probably a DK40 or DK45 probably a se version it is pre 2010 with the older light gray chassis paint. Also no emissions on that tractor, which is good. Nice tractor if you can get it running. It was common for the switch to go out on these, about $100 for a new one that...

It sounds like it is probably the main power going to the display. Lots of times it can be caused by the main start switch Spray some WD40 in it and work it back and forth a few times to see if that does anything. Next is to check the fuses, the one for the dash is the combimeter one normally...

I figured out that my main key switch is not getting power to the relay to turn the cab on, which is also affecting the rpm gauge and bat charging. I sprayed it full of silicone Wd40, worked it back and forth a few times, and it came out of it. I will probably need to replace the switch in...

I Lost all power to my CS 2410 factory cab today looks like it is probably a relay up in the cab as there are only 3 wires that go to it: Red +12 power, Black ground, and a Red/white for ignition on that I assume activates a relay in the headliner to power up the cab. The Large 20amp fuse in the...

I needed an extra set of hydraulic ports to be able to adjust my top chute deflector, but I also wanted the possibility of rear remotes as well. So I ordered the optional rear remote kit and then also ordered the extra parts for the front kit, as well as pipes and front disconnect mounts. I then...

I have the 60in MMdeck on my CS2410 mows like a dream very heavy-duty deck and it never clogs like my Deere one would. Just make sure it is adjusted correctly both on height (correct reading to the lever) side to side (level) and front lower than the back so the middle scalp roller works. Should...

Just put a set on my Kioti CS2410. Have to say they are really good did some loader work moving compost and they never slip even on dormant grass where the snow just melted.

Just picked up a cs2410 with the field cab and plan to mow with it this summer. Since it doesn't have AC I will probably plan to remove the doors and store them off the tractor for the summer. anyone have any good ideas for storage so I don't end up breaking them? Also I have done many tractor...

Would it still rotate the correct direction?

I have a 2015 CS 2410 and it came with a block heater. It is in the single freeze plug on the left hand side of the engine will get a picture of it tomorrow. I didnt see any numbers on it but will look harder. I always bump the throttle up just a little bit off idle before cranking and that...

It is the same as Cub and JD 5 bolt 4.5" BC 13.13 center hole 1/2-20 lug bolts.

Does anyone know what the bolt pattern is on a the kioti standard 26-12-12 rear wheels that fit a CS2410? I want to make up some spacers and figured I would ask before braking out the calipers. I think it is 5lug 4.5bc 3.13 center hole dia

John Deere should be a little concerned looking at some of the new combine/tractor technology coming out of Europe. This system could be a serious game changer especially in soil compaction.

My dad has 2 of them on his farm here in Maine one articulated without a cab and one with wheel steering and a cab. At 70hp he can snowblow his mile long road no problem in comfort. Awesome machines, best hay mower ever invented he has a front mount dual disc mower conditioner that lays down a...

I have a 2014 tier3 CK35 400+ hours on it and haven't need to adjust the clutch yet. Yes it does have a hook that will allow you to disengage the clutch for long term storage. The biggest issue is if your in a humid environment the flywheel will rust and can build up large rust areas in the...

A reminder for anyone that stores their Backhoe outside, make sure to check under your valve boots for water both of mine had quite a bit trapped in them. I even had it tarped but the water still got in there. luckily I caught it before the valve spools rusted and started leaking. I removed the...

Here are the pictures of the skid plate I made to protect mine. I just knew it was only a matter of time especially while working around stumps and in the woods.

Just get some of these chains. Use them all winter and when I am logging in the summer and never get stuck. Are your tires loaded it can make a huge difference.

Just finished rebuilding this for my Dad we found it on Cl last spring. Antonio Carraro trx 8400, Reversible console, 70hp, 84" blower. He has a mile long private road into his farm. We avg 130" of snow a year 2017 we had a 2' storm should be interesting to see how well it handles it. He can't...

All refurbished and ready for winter snow blowing, should work great on my dads mile long road!

Not sure if yours has it but most Kioti's have a spare fuse with a rear connection point. On mine I actually found the connector on line that fit it and used the power to wire in my 3rd function valve. Here is a picture of mine, Rear right hand side.

Mowing some cover crop, just need to do some painting on it, replace the door seals and find out where the ac is leaking.

Currently rebuilding a TRX 8400 2002 year reversible not articulated with a cab for my dad, we found it on craigs list this past winter has 1000 hrs and only looks like it has been used to tow things around and plow. Unfortunately someone ran it into or backed it into something and destroyed the...

Not reversed they are all that way CK2610 Demo Part 1 - YouTube Makes it so they wont fill up with water if it is left outside disconnected. even my older ck35 is the same

See picture Remove cover screw in 2 turns test machine and under heavy load look for black smoke, if none turn up more. Once you get to the point where you see black smoke under heavy load back off the screw 1/2 to 1 turn. Best way is to use a dyno for an accurate measurement. Good video on...

Seems legit, found on the facebook.

Save your money for a grapple. I messed around with forks for 2 years, now that I have the grapple I would never go back for moving log and brush. Forks are great for something on a pallet.

We had quite the wind storm Monday this week, still no power. I decided I better do some clean up on the front yard and drive way before it snows, don't think my snow blower will like all the branches. I found that my chain harrow makes a great debris rake!

If you look at your first picture there was a problem with the loader assembly from the dealer. On the bucket angle indicator rod ( the thing that bent ) the orange tube you see down by the base is suppose to be screwed on to the upper bracket where the other orange tube is mounted. The dealer...

I went with this valve and the same do3 sub plate your looking at 12 VDC 21 GPM ARGO RPE3-6 DA HYDRAULIC DO3 SOLENOID VALVE | Solenoid Valves | Hydraulic Valves | Hydraulics | www.surpluscenter.com Only reason was it was able to handle a much larger flow and pigtails instead of a bulky...

Bush hogging around my field last week without my loader on, I heard a crunch up front so I stopped to take a look and found a nice 2"dia branch shoved up through the plastic shroud below the hood into my battery. Luckily I stopped a soon as I heard it and no major damage done just a broken...

Only here in Maine! Landlord upset with plant removal runs over tenant with tractor: deputies | WLBZ2.com

This 55" grapple is excellent at lifting anything. Used it to unload some timbers off my trailer. Then today helped a friend cut some trees for a power line and he gave me all the wood. So I cut it up 4ft length and loaded and unloaded it from my trailer. So nice to be able to clam shell down...

Thanks for all the kind comments. Here is another pictures with the kickstands installed and it lifted off the ground. It was way to windy here to paint today hopefully I can get it done before it rains again.

Bought a 6x8 chain harrow set from Tractor Supply last week but needed a 3pt lift so that when I work in my cover crop seed I don't have to worry about pulling it all out of the garden. Most of the lifts I have seen were around $5-600 so I figured I could use up some scrap and come out ahead...

If you take up the seat it is the steel line that comes up from the loader valve to the rear end and ties in right next to the 3pt down speed adjustment unit here is a picture of mine where I replaced the line with a 3rd function valve.

Thanks here is another picture of the plate removed I also made a port with a cover plate so that the HYD oil filter can be removed without removing the plate. It was also a bit tricky getting it in there without interfering with the backhoe sub-frame.

Loving my new 55" EA Wicked root rake grapple. Moving one of my big brush piles out of my field. Love the clamping force and versatility of it. Works great for picking up logs, brush and stumps been ripping out a bunch of alder stumps with the nice soft ground. Yes I know the ROPS is not all...

That's why I added a skid plate on my Kioti probably same location. With all the work I do in the woods around stumps I knew it would only be a matter of time.

Jeff I have a 1/2 barrel full that weighs in at around 550lbs and that seems just about right for my 35hp kioti I also have Rim guard loaded rear tires.

If anyone is interested I found a source for the customer use electrical connector plug that fits the older CK series, and probably many others. Here is the link in ALI express, took about 2 weeks to get them but they fit perfect, and were cheep. KET 5 sets Kit 3 Pin Way Waterproof...

Well finally got my install wrapped up and the grapple works great spent a couple hours moving an old brush pile in my field to the burn pile I have on the edge. Most difficult part was getting the 1/2" steel tubing lined up and bent correctly to line up with the fittings in my valve block and...

This is the one I just got it is a sure grip control AU handle Seems really comfortable and use the thumb to push the buttons. Sure Grip Controls All of the Kioti flare fittings are JIC and usually the straight threads are BSPP or Metric

Hi Steve Thought I would post how I am making out following your method, got most of the plumbing done today and also made up my QD attachment plates, almost looks factory! I am mounting my valve down On the bracket that holds the hydraulic filter it gave me good access to run the lines forward...

I had a Kelly B10 3pt Backhoe with an interesting system. It had a set of adjustable arms that attached from the top link position down to a plate that bolted to the drawbar in conjunction with the standard top link, so it added another triangle brace so none of the prying or pulling motion...

not sure how much different the ck35 is but no spacers needed plenty of clearance for these.

If you go to square or diamond you will always have chain on the ground so it greatly smooths out the ride. With these i generally don't notice a big difference in ride quality from a bare tire.

I usually cut my trees around June time frame then haul them out to my landing on the edge of my field there I let them sit all summer with the branches and leaves on in the sun, it tends to draw a lot of moisture out of the wood. Then in the fall I trim off all the branches and push them into...

With a Ball in my draw bar the height is to low for my wood trailer on my CK 35. Does anyone know the part number for the European bolt on bracket to the Kioti CK draw bar as shown in this first post (kubota one). http://www.tractorbynet.com/forums/kubota-owning-operating/200741-what-part.html...

I cut mine off and installed new axles with standard trailer bearings so I could use HDAP tires all round.

Back to the OP, you can still purchase all the pto extension parts from Deere For the frame extension you will need to find one used. ebay is usually the best bet.

The pictures in the amazon ad show the wiring diagram, the positive goes to the open side of the solenoid and the negative goes to the other post on the motor. Frame is not grounded.

I finally got a chance to install the bushing and heater today it went pretty smooth. I removed both the loader frame and the muffler to have room to work. I used a punch to push in the side of the freeze plug towards the operator station. Once the antifreeze stopped flowing out I grabbed the...

Got the parts in and now I have the correct heater for the bushing, the one in my original post was a 1" instead of the 3/4 needed. Here are the links to the correct amazon parts if anybody wants them. Heater Amazon.com: Zerostart 310-0002 Engine Block Heater: Automotive 37.47 Bushing...

Just got my auto temp scalder built. Used a 5000w element from a steam table draws about 20a at 240v. Bought the sink on ebay and reinforced the legs. All in around $400 for all the parts bought the controller from mcmaster.

Pulling from the 3pt is fine as long as your careful, all of the winches are set up that way. With just the draw bar it is tough to get the front of the log up of the ground. Just go slow and stop if the front wheels rise. Helps even more if you have a load on the forks. With most of the...

CK series have stickers or at least mine does!

I just noticed on mine that they changed the tube design and removed the 90deg fitting, probably because it leaked! Here is my thread on the skid plate. Did a bunch of logging this past weekend and was glad to have it...

I went with the direct drive as well found a washdown motor and a bolt on gear box on ebay. I put a few fingers pointing down under the plate it really helps to fling out the feathers also did a spray around the rim helps a lot. Used a roof stink pipe seal around the shaft to keep water off the...

Here is a picture of what I did. Low profile and works great. Just used a large wave washer with a small spacer under the bolt head.

Finally got the finished product all painted up and installed. Found a color that matched pretty well it was RAL 7021 Black Gray. I used a epoxy paint so hopefully it will hold up well. I was able to bolt into 3 different locations one just below the rops bolts on the rear, 2 bolts into the...

I have noticed that with my 2014 CK35 it gets hung up (2 wheels spinning) much more around my yard than my old kubota L275. Its normally not a problem just hit the diff lock and continue. Looking at it I think the front axle articulation is about 1/2 what the kubota was. Has anyone adjusted...

Looks great pekan! I have mine mostly done both the frame and base plate are finished just need to make up the sides then paint it up pretty. I went with the filter trap door that I had seen on some other ones. Had a challenge keeping it up tight to miss the backhoe frame.

Hi Everyone Just replaced my 80's kubota L275 with a 2015 Kioti CK35 what a difference! easier starting much faster loader and great backhoe. One thing i noticed is that the hydraulic filter hangs down quite low and i will be using it in the woods for some fire wood logging and worried about...