Search results

Personally, I'd go with a brand that has a servicing dealer near by.

That's a very good point, what's easy now probably won't be in 10 years.

You seem to have your mind set on the QA forks, which are nice, no question there. For your stated use however, a set of clamp on forks would serve you just fine, and come in at less than $200. Money saved could be used for another implement down the road.

It won't hurt a thing to keep it outside, mine is under cover, because it's available to me. If I didn't have that available to me, I would just put it up on blocks, and throw a water proof tarp over it.

I keep my implements under cover when I can. Flail mower and tiller stay in a storage building, everything else is under a lean to that is up against the barn. My tractor stays in the garage, keeps the mice and other wildlife out of the electricals, and air cleaner. One thing I've done for my...

Thank you!

Hey all, I need to change the spin on hydraulic filter on my Mahindra 4035, can someone please tell me roughly how much fluid I'm going to lose? I'm assuming about a filters worth plus a little more since it sits higher on the tractor. Thanks

I thought that's what I said..LOL :unsure:

Does your tractor have a single or dual air filter setup? Someone may have forgotten to install the secondary filter, and fine dust that passes by the primary filter is what that is for.

If you are talking about voiding your warranty, I do not believe you do, just save your receipts, and use OEM approved products.

🤣 🤣

Thank you, so what I'm hearing is that I can't really over grease it.

I have a 4035 Mahindra that has two grease zerks near the front axle. Mahindra calls them "pillow blocks" in the manual. I've greased them, but don't know how much to apply, I can't hear it or see it to know it's full. Any thoughts?

Yeah, I would clean it and put it back in, then you are good to go for 1000 hrs, at least on the PST transmission, can't speak for the other models of the 4035.

Sure, it's both through life experience, (30 years in rubberized products) and through this site. What I found was that silicone flat stock tuned gooey when exposed to gasoline and diesel, as a general rule. Here's the site I use, it's 4 pages but is alphabetical so that helps. Rubber...

Your choice, but if I'm going through the trouble to hand cut a seal, I'm going to choose the best material for the job.

100% agree with the Buna-N (Nitrile), Neoprene doesn't fare well with gasoline or diesel.

I had a MF 255 that called for Permatran III, I used TSC's universal tractor fluid without any problems, I checked before I used it to make sure it was compatible with the Permatran, and it was. No problems whatsoever.

In short, Silicone is not a good recommendation for either gasoline or diesel. Nitrile will be your friend. Silicone has an unsatisfactory rating for both, and will turn to mush.

I have this exact same tractor, Mahindra 4035 PST (2015), and use it frequently. I do all of what you are wanting to do with the tractor, and it has never let me down. I've brush hogged grass that was taller than me, but I did have to drop down a gear, to Low 3. I use it to clear snow in the...

Rocco611, You didn't by any chance put it on a credit card, did you? That could give you some footing when talking to the manager.

For my gas and diesel cans I drill out the air vent with a 3/8" drill bit, then go to the hardware store and buy corks, that press fit into the hole. I do the same with missing snap on caps the filler spout when eventually fall off. Has forked for years.

This ^^ exactly when we moved into our house our barn was full of mice. We got one cat and then another. We feed them, and they have a heated water bowl, and right now they are parked on a Lazy-Boy I found in someones trash with a heating pad on top. We have zero vermin, and they help with the...

Some animals are called different things around the country. I assume you are talking about what here in Michigan a Mole. Here's my technique for Moles, the little suckers that that burrow a tunnel just under the grass. They have primary tunnels that they like to keep open, if you stomp them...

Here's my .02 if you have acreage you need a tractor, I have a Mahindra 4035, and use the bucket all the time to "tote" stuff, especially firewood. That being said there are times I hire things done. I bought 2.5 acres that butted up to our 10. It was so thick, and full of Honey Locust thorn...

I have a similar problem with a John Deere rotary mower. Mine's used and the the output shaft's hole is slightly oblong from wear. I shear bolts all the time. When the bolt is installed and snugged up I can rock it back and forth. IMO that is the OP's problem, If he bought it new, JD should fix...

Hi all, I am looking for an aftermarket hydraulic filter for my Mahindra 4035. After my first motor oil change I cut the OEM filter apart, and found it was a Fram clone. Glued on cardboard end caps, that I paid $27 for. Fortunately, I was able to cross the oil filter to a Baldwin B202. I have...

Hi All, long time looker first time poster. I have a Mahindra 4035 shuttle shift. I need to replace the 10 gallons of fluid it holds through what appears to be a 1/2" fill hole located right above the PTO output shaft. Does anyone have any tips or tricks for adding that much fluid through such a...