Search results

Fit Rite Hydraulics is who I used, he is great to work with and answered any and all my questions prior to purchase. I had him make me a top and tilt set for my MX5100,

I bought a 4k lb capacity pallet fork for my MX5100, I think it's lift capacity is 2700. They are on my loader more than my bucket.

I have 44 acres. I do lots for log pulling for firewood tight stuff, I do 10 acres in food plot activities. Grade about 1/2 mile of gravel road. I own a 2011 MX5100 HST, great tractor for my needs. I wish it was a little smaller more often than wish it was bigger, but it is actually the perfect...

I thought about a grapple bucket was almost gonna buy one for my X5100. I got some great advice from a friend, he said buy pallet folks. They weight less than a grapple, cost less than a grapple, and do about the same job. My pallet folks on on my tractor more than my bucket. I have never...

Been off line for quite sometime, unable to reply. Back on-line. Thanks for the reply, unfortunately the MF50 which I was working on belong to a friend of mine and he took it back to it's home before I got a chance to snap any photos. On a positive note, he took the Massey 50 to the county fair...

Sorry for the late reply, health issues. Yes I have gotten the MF50 all fixed now. Installed new clutch kit and the tractor is back together, Runs great, thanks for the reply and again sorry for the late reply.

I Have a MF50 split to install a new clutch (dual). The reason for the split is the PTO fiction plate was completely burn out and shredded. With the tractor split should I be able to turn the PTO shaft by hand? I don't want to put it together again just to burn out another plate.

I have a MF 50 runs great, drives great, but the PTO wont engage. I just recently acquired this tractor so don't really know where to start.

Does anyone know how to tighten up the cruise control on the MX5100, mine won't hold at all. It work for about 1 year now won't hold. Thanks:confused:

I have an MX5100, tractor is great except the cruise control lever wont hold. I place it where I want to speed to be, it holds for a few minutes then slowly returns to stop position. It starts out great but then you can feel the tractor start to slow as the cruise control lever moves back to the...

Here is the ballast box I made for my Mx5100, cost $25.00, turned the tractor into a new machine as far as what I could comfortably do with the front loader.

Yesterday I changed out the fuel lines in both tanks on my F935. The right tank fuel line inside the tank was broke in half, the left take had no pickup line at all. I changed them due to running out of fuel, and the fuel gauge read full. Once I got those changed out, I put everything back...

I got it, put some of my personal touches on it. Pats Quick Hitch. Hook up my large disk and did an acre food plot on my back pastue. It's great...

Well I bit the bullet, trading in my L3400 for an MX5100, suppose to be delivered today. Hoping this is the last tractor I have to buy. I love the L3400 but it just didn't have enough umf for what I intended to do with it. So here I sit waiting for the dealer to deliver my MX5100. P.S. I...

OK, so you might say I put the cart before the horse, so here is what I need advice on. I own a L3400, great tractor I used it for bush hog, and disk. I bought a new place (41 Acre) soil is more clay than sanding of my old place and the L3400 was starting to strain a bit with the bigger disc and...

OK, so you might say I put the cart before the horse, so here is what I need advice on. I own a L3400, great tractor I used it for bush hog, and disk. I bought a new place (41 Acre) soil is more clay than sanding of my old place and the L3400 was starting to strain a bit with the bigger disc and...

Anyone know where I can get an Electric Bed Lift for my Club Car 1550 XRT. I love the XRT, wanting to load the dump bed with gravel for some road repair on the ranch. I think the electric lift would come in real handy for this type of work. Thanks

New owner of a 2009 L3400, am looking at getting a new rotary cutter and what to make sure I get the most efficiency out of the new mower, what size should I be looking for. I will be mowing about 12 acres pasture pretty flat with a couple on medium slopes. The l3400 has a loader on it but no...

OK, new guy, so I have a question. I buying a 2009 Kubota L3400 HST with a front loader, 6' Finishing Mower, 5' Box Blade, and Tanden Axle Trailer. All were purchased as a package, tractor has 70 Hours on it, always garage kept, The guy is selling it for $ 16500.00. He doesn't need it any longer...

I just bought a 2004 B7500 with 165 Hours, a 60" MMM, paid 8500 for it. Everything on the tractor works, it is great shape with a little ding in the hood, and a scratch on on fender. The MMM works great. It doesn't have a FEL, and I beleive I am going to have to put front weights on it to handle...