farmtrac 60

I replaced hydraulic line going to cylinder on front end loader after finishing it will not move at all I don't know where bleeding valve is located on the tractor or the best way to go about getting air out

I recently changed the oil in the 2003 tractor (1000+ hours). I topped off the injector pump oil at the same time with the same oil. Since then, as expected, some overfill drained out the drain from the drain line. Now though, as the tractor is running it seems that there is a pretty...

Won't crank...tries but acts like not enough battery. Replaced battery & starter still won't turn over. Pulled INJECTORS and it turns over just fine. No funny noises, injector pump working. Replaced injectors...still won't crank. I have Electrical Wiring Diagram for FT-60 if anyone needs.

I have a 60 that sat for 2 years and it runs wide open when it fires up. Also the kills switch has no affect. Hoping for something simple to try before pulling the pump. Thanks

Does anyone know if there is a cross reference with ford or other parts?

I have a Farmtrac 60 that the Long 5320 loader hydraulics are slow to work?

Unfortunately I have lost the original equipment stabilizing chain and turnbuckle off one side of my 60. I would like an original to replace it or one of the same design. I have searched the web but the resources I have found that gave one that appears to look the same as mine are all out of...

How to replace starter on 2000 farmtrac 60

How does the starter come out on Long Farmtrac 60

I inherited a Farmtrac 60. It has been sitting for around 6 years. Got it to crank but appears to be running wide open on 2 cylinders. It has a Bosch inline injector pump. I replaced the oil in the governor with no changes in the RPM. Any suggestions to get throttle control working? The kill...

I don't believe my fuel preheater is working. I have about 850 hours on my tractor. I don't feel any warmth at the manifold preheater. I could not find a part number for the preheater. Troubleshooting recommendations are appreciated. The tractor is primarily used to skid logs to my sawmill.

I have gone brain dead and just wanted to make sure I was remembering correctly. The rear axle and hydraulics share the same fluid? It uses regular 90w gear oil?

need head tightening sequence and torque for head bolts

need the sequence for tightening head bolts, 3 cylinder diesel

Replacing head gasket, need to know torque for the head bolts and sequence for tightening

Now that TPG helped me get my fuel injection pump working again I can move on to my next puzzle. What size/type of male fitting do I need for a Farmtrac 60 hydraulic remote? I just purchased a Norwood Skid Winch which uses a capstan powered by a hydraulic motor. The hoses are 1/2 inch and the...

Anyone have a diagram for the switch for a Farmtrac 60? its a 7 post switch.. All the replacements seem to be 6 post.. in search for the wiring diagram for this thing in order to "adapt" a switch to it.. thanks much!

Just finished rebuilding the power steering cylinder on my 2000 Farmtrac 60. Not an easy job but doable in one day. I got my parts from Robbie at Joe's tractor parts in N.C. Fast service. For anyone attempting the job when you get the rod out of the cylinder look at the parts kit and do not...

Free for viewing and printing at my website. Tested and you can download and zoom in with your browser and read all the fine print. The foldout wiring diagram is 4 pages long so if you print you will have to tape together. Apologies for not having this done a long time ago but...stuff happens. Jim

I have a new Farmtrac 60 service manual for sale on ebay Farmtrac 60 Service Manual (131340801303). This one comes with the original plastic wrap...it is a later dealer sold black and white reprint that does not have the color diagrams. I have published color copies of my earlier service...

I need to replace the tie rod end dust boots on my Farmtrac 60. Does anyone know of a suitable replacement? Thanks.

Anyone removed the starter to clean the pinion as specified in the operators manual? I'm having trouble getting the rear bolt. Jim in SC

i have a farmtrac 60 and my ignition switch has been all unplugged does anyone know which order the wires go. or maybe a pic of switch with wires attached or a wire diagram, please

I received an ignition switch for a Farmtrac 435 instead of a 60. Will this switch work on a Farmtrac 60 and if so, where can i find the wiring diagram for this switch?

Love my tractor but hate trying to find parts. 2000 model FT 60. The headlights are sealed beam units set in black plastic frames. I need two. Anyone had any luck finding these or crossing something over? Thanks in advance for any help.

The PTO clutch was not working on my tractor and I had a new clutch installed. The new clutch engages the tractor and the PTO at the same time. It releases the PTO but I cannot release the tractor and let the PTO keep running. You cannot feel a two stage clutch it just feels like one...

Farmtrac 60 The PTO clutch does not work and I have ordered a complete clutch assembly to install. I need to know if it is neccessary to make any adjustments on the clutch or is it pre set where it needs to be. Need to know if it needs any adjustments prio to installing, or is it pre...

Tractor has always started and ran great. Bushhogging today and it started losing power. Would barely run under no load. Noticed white exhaust intermittently. Drained fuel filters and added diesel fuel treatment. Started and ran decent but after about 10 minutes of work laid down again. Digging...

Hooked up wood splitter today and no pressure. The hydraulics had been acting slow and jerky over the summer. Fluid is milky. 3 pt hitch will barely lift unloaded. I unscrewed the hyd filter and it barely has trickle coming out of it with engine running. Guessing pump? If so I am seeing 2 $200...

There are four wires. One yellow (large one) goes to the battery. One white (medium size wire), one orange and one blue (small size). Blue and white wire have plug on end. Here is the alternator pic. Please help if you know where these wires go.

Answered.

Removed

Where can I find a manual on a farmtrac 60 tractor?

I am still having a problem with starting after replacing the starter safety switch.It started with no problem after i replaced the switch but now it's hit or miss.I can sometimes jiggle the shifter(high/low)and get it to start but it is a pain.Any ideas on what i am missing or need to do to...

I am looking to find a way to bypass the starter neutral safety switch on my 60.It seems that it is getting very picky as to when it will or won't start.Sometimes just jiggling the shifter and it will start but lately it has to be pulled.Is there a way to bypass this or is there a part available...

My starter Bendix is not working, does anyone have a part number for the starter or Bendix so i can try to rebuild this unit myself.? And do you have a PN for the fuel filters primary & secondary, i have 72nh9176 & no one can cross ref. thanx

Hi, I was recommended to this forum as a place that we might find the parts we need for our Farmtrac 60. A little background; Last summer we were haying and had a neighbor boy driving it over to the feild. He ended up hitting a tree with it and had done extansive damage to the front end. We...

Does anyone have any input as to whether or not a person should invest in a Farmtrac tractor, considering their problems? I have an opportunity to buy a 2003 60 with loader, rotary cutter, box blade and trailor for $10600. Tractor has a little over 100 hours on it. What do you think?

Above is data I've collected on my website. So far it looks like Farmtrac 60's are concentrated on the east coast of the US. It is interesting to see where this escorts model or maybe even old Ford 3620's are located throughout the world.

My tractor has a Long 5320 loader mounted. What other manufacturers make loaders that fit the farmtrac 60? Where can parts be purchased for the Long 5320 loader? Thanks, Jim

For Farmtrac 60 owners I have posted a copy of my manual in a .pdf file. Even though not as extensive as a service or parts manual it provides lots of useful information for the Farmtrac 60 owner. I don't know but some of the information may be useful for other Farmtrac models. Just visit my...

New items are in bold. Near 375 hours. Didn't use the tractor as much since my trails are all cut and all I need to do now is mow a couple of times a year, haul firewood. This list is also posted at Farmtrac 60 tractor-parts cross references. Below is my list of things done to repair my...

Like many of you I bought the Farmtrac 60 because it was pretty much a copy of an earlier Ford model. According to the parts manual the Farmtrac 60 is modeled after the Ford 3620 (see page v of the parts manual). I have put together a webpage to collect cross references for replacement parts...

Father in law has a Long Farmtrac 60 and all the local tractor places say they can't get parts. I'm needing sleeves and pistons. Have serial from engine and chassis if it helps. I've searched on Google and everywhere I can think of and can't find anything. Please help

I put an injection pump on a farmtrac 60 and now I am having trouble with the pump timing. It has been a pure head ache from the start. I dropped the half moon key down in the engine and had to fish it out with a magnet but I got all of that squared away. I have some how managed to get the...

Running any tractor in the woods is prone to cause problems. My Farmtrac 60 has developed a pretty good leak of hydraulic oil from the right side of the differential where the low pressure return enters the housing. I've had some tree limbs get stuck or jammed in that area so I suspect that is...

Hi, Here is an update on my 2003 Farmtrac 60. I purchased the tractor new in 2003. I've made periodic posts on how I like the tractor. Tractor has about 225 hours on it today. I still like it. Here is the latest info. As I said before I was missing a grease fitting and I had a...

Guys, My dad saw this along the side of the road and didn't know if this is a good deal or not? Farmtrac 60 2001 180hrs 2wd - no implements - no loader $10,000.00 Sounds like a good price, but I'm not sure Any problems with these that he should know about? Thanks

This year I am in the market for a backhoe for my tractor. I plan to use the backhoe for ditch digging and ditch maintenance. I have one large ditch to maintain. It is about 1/4 mile long and will have to maintain from the side. The ditch digging should be straddle jobs. I really like the...