mahindra 4025

  1. jdilemma

    Mahindra 4025 with nimco cv 112 controller

    I am having a problem with the nimco cv 112 controller when I move the joystick left and right to control the bucket I get absolutely no respons at all and the joystick acts like there is no load at all on it.
  2. S

    Mahindra 4025 w/ AML333 front end loader

    While trying to connect a bucket to the AML 333 Quick Attach System I discovered one side was tilted more than the other side. Using the hydraulic controls I could tilt forward or backward nut the to mounting plate would not line up. One was tilted more forward that the other. At first I...
  3. F

    Mahindra 4025 grinds gears even with clutch all the way in

    I have a 4025 that has less than 300 hours on it. That said, I've only owned it for about 2 runtime hours of that (haven't really started using it regular yet). When I test drove the tractor, everything worked fine, shifted nicely, no issues. Last week, I noticed that when I try to go into...
  4. H

    Mahindra 4025 fuel tank cleaning.

    For the past few weeks, I have been plagued with the screen in the tank stopping up. It has been suggested pressure washing the tank then washing it with clean fuel to get the water out. I sure don't want to remove the tank. Someone suggested cutting the fuel line and install a cheap throw away...
  5. H

    Mahindra 4025 fuel tank cleaning.

    For the past few weeks, I have been plagued with the screen in the tank stopping up. It has been suggested pressure washing the tank then washing it with clean fuel to get the water out. I sure don't want to remove the tank. Someone suggested cutting the fuel line and install a cheap throw away...
  6. F

    Mahindra 4025 Hydraulics

    I just bought a 2013 Mahindra 4025 4x4. I have a line that started leaking, the line comes from under the seat and runs to the bottom of the tractor. It has three bajo fittings under the seat, 1/8th in. steel line and is crimped to a braided rubber line then goes back into a steel line under...
  7. F

    Mahindra 4025 Hydraulics

    I just bought a 2013 Mahindra 4025 4x4 and a line started leaking that comes from under the seat. The problem is that it is leaking gear oil and Mahindra says it is not supposed to be gear oil in it but the man that owned it said it was always serviced at the dealer. Now I am trying to figure...
  8. H

    Tire Selection  Mahindra 4025

    Need a change from narrow 3 rib front tires to a fat flotation tire of sorts. 2 wheel drive with loader, it will get stuck in a min. Please I don稚 want to break the bank and don稚 want to take the loader off and on. Thanks
  9. S

    Mahindra 4025

    I have a Mahindra 4025 and the fuel line from the filter to the pump is leaking at the bottom crimp, can I just cut it there remove the crimp and slide the line over the tube and use a hose clamp to secure it, there seems to be enough length in the line to do this, but also will the flex line...
  10. R

    Mahindra 4025 Backhoe Attachment (2)

    Anybody put an aftermarket backhoe attachment on the Model 4025 Mahindra? Say a WoodMax or Ansung, etc..
  11. R

    Mahindra 4025

    I have a 2013 Mahindra Model 4025 2WD tractor. Almost without failure....if I run the tractor for say 45 minutes to an hour......it starts losing power....(starving for fuel....seems the same)....Gradually getting worse & worse. To the point it's smoking a little & barely moving along & trying...
  12. R

    Backhoe  Mahindra 4025 Backhoe Attachment

    I have a 2013 Mahindra 4025 2WD tractor. Been looking at purchasing a 3-point backhoe attachment. I spoke to the local dealer today (where I bought this tractor new)......he says they have a new Ansung backhoe attachment that may or may not work on my tractor. He didn't know. He says he ordered...
  13. P

    2014 Mahindra 4025 Fuel tank leaks

    The back story I've gotten is Mahindra didn't make fuel tanks with great lining. If the diesel gets any fungus, that eats the tank lining, which exposes the steel to rust. My 2014 4025 has under 260 hours and the tanks developing pin hole leaks. Online research tells me a new tank is about $500...
  14. P

    2014 Mahindra 4025 with 333 loader offset quick attach plates

    Over the weekend, moving tree limbs with my new Titon forks, I noticed the left QA plate wasn't engaged in the forks. I stopped working and attempted to force it back into the locked position, but had no luck. It was late, so i parked it for the day. Monday after work, and some internet searches...
  15. R

    Flat Proofing  Mahindra 4025 left Front rim broke in half

    While brush hogging today I thought I had fell in a hole but it turned out the front left wheel had cracked in half (not vertically but completely around the rim). I can see what appears to be a long time rusting crack where it fell apart. I can replace the wheel and tire but the one that came...
  16. R

    Temp and fuel gauge on mahindra 4025

    Temp and fuel gauges on 2012 mahindra 4025 stop working. I changed the fuel timer (relay) because it had a raddle like something was broken inside, but that didn't fix the problem.
  17. R

    Mahindra 4025 (4wd) issues (Loader Control Valve & Clutch Pedal)

    Mahindra 4025 (4WD) Problem #1 - I have a Mahindra 4025 (4WD) with the loader. When going backwards and using the float feature on the front bucket control valve, I have to manually hold the bucket control lever in the float position. If I don't, it will flop back down to the UP position if any...
  18. R

    Mahindra 4025 clutch pedal issue

    Our 4025 4WD tractor has what is apparently an older design clutch and brake pedal setup. The tops of the pedals are relatively smooth and several times my foot has slipped off the clutch pedal at an inopportune moment. I called the dealer and they tell me the newer models have a redesigned...
  19. T

    What is this pin? Mahindra 4025

    Manual no help. Google search for images,diagrams no help. Various part site search engine,part guide no help. I'm tightening the bigger plug/nut back and about to need a cheater bar. That goes up and down freely. There may be thread on the end of it but the nuts not far enough up in their forte...
  20. T

    4wd Mahindra 4025 pin touching driveshaft

    Drained the diesel and cleaned filter yesterday. A friend gave me 3 buckets of diesel as a friend,for letting him use it and for hunting on land. Was pouring one in and hadn't gotten to the last 1/4 and a ton of gook came out. B4 I could stop and grab the funnel (I'm a paraplegic btw) the gook...
  21. D

    Mahindra 4025 Clutch / Transmission

    First day of working with my "new" 2012 Mahindra 4025 4WD. Has about 1120 hours on it. I reversed to drag and spread some gravel up a slight hill using the loader. When I depressed the clutch to coast back down for the next pull, with the transmission still in reverse, the clutch pedal...
  22. T

    Mahindra 4025 4wd front seal replace cost

    I went to use the tractor today and noticed some oil all over the rim. Looks like the seal is bad. I've never replaced a front axle seal and I do worry about tearing it apart and biting off more than I can chew. I've replaced several trailer seals and bearing but this looks more complicated. If...
  23. Z

    Draft / Depth Control on 2012 Mahindra 4025 2WD

    Forum I am new to plowing ....and tractors Hooked up the plow to my 3pt , but I cannot get the plow to break into the ground. I have Position Control on lowest and Draft Control deepest setting. The plow just appears to float on the ground. Any advice ? Thanks Zach
  24. ki4amd

    Cleaning Transmission Oil Strainer on Mahindra 4025

    My question is a simple one, but I can't find any information online or in my manual. The manual says I need to clean this strainer after 50 hours, and now is the time. It does not say I need to change fluid until I get to 1000 hours. I'm really not excited about changing fluid as that stuff is...
  25. T

    mahindra 4025 intake heater and knock

    I couldn't get my tractor to start after using it for a while today and started checking the basic fuses and was getting no power to the starter when turning the key. I checked the safety switches and they all were good and then I noticed with the key on the intake heater had a small puff of...
  26. mikeestes99

    Mahindra 4025 RPM gauge doesnt work

    hello to all and thanks in advance for the help, i replaced the alternator on my tractor and now the rpm gauge doesn't work. it worked fine before. any ideas would be greatly appreciated. thanks mikeestes99 jasper, AL
  27. M

    Mahindra 4025 suddenly died, now only cranks

    I have a very new (4hrs) Mahindra 4025. Bush hogged for 2 hrs and all of the seat nuts fell off. I fixxed the seat. Tractor started right up. Drove it about 100 ft and started to lower the bush hog. That's when it died. Now it only cranks but won't start. Need suggestions. The dealer gave...
  28. M

    Mahindra 4025 suddenly died...now cranks won't start.

    Hello all, I have a brand new 4025 4x4 with loader. I had to work on the seat as all of the nuts vibrated off after 2 hrs of bush hogging. Replaced the nuts. Tractor started right up, moved it 100 feet, started to let the cutter down and Suddenly died. Now it Cranks good, will not start...
  29. T

    Oil & Fuel  mahindra 4025

    hi and thanks for having me as a new member. tuesday night here in middle tn it got well below 0 degrees, my tractor cranked on wed and i was backing up to a roll of hay it died and has not started since. it is only 3 months old, i had no fuel additives in the fuel. today i bought some 911...
  30. G

    Oil & Fuel  Transmission oil screen - mahindra 4025

    The manual for the mahindra 4025 suggest cleaning the transmission oil screen at 100 hours along with changing the tractor fluid. Other than removing the right side running board and brake linkage how do you get the screen out. Must be a trick I did not see.
  31. W

    Loader  Mahindra 4025 aftermarket loader

    I am looking for a loader for my 4025 2WD that I just got. Any suggestions on good aftermarket loaders(or other equipment)?
  32. J

    Backhoe  back hoe for Mahindra 4025 ?

    Hi everyone...new here . Just found this sight while doing some research. Anyway in may I bought a new Mahindra 4025. I got with the loader only. Now I'm thinking about adding a a backhoe. My Mahindra dealer told me a Mahindra hoe was gonna run around 9k....:( ! So I started looking around so...
  33. C

    mahindra 4025 2wd wheel noise under load

    I hear a clicking sound when my tractor gets under load. I just bought this tractor and don't know a lot about it. Please help. It only makes it when wheel stops turning under a load. Is this a problem or by design? Thanks in advance for your help.
  34. M

    Hydraulic Issue Mahindra 4025

    Hi All New to the board. I recently bought a Mahindra 4025 which I'm already in love with. Added a few mod's, sun canopy (basketball backdrop), aux. lights, grapple (versatech). So the problem I'm having is this; Installed the grapple and decided to run it off the power beyond with a joystick...
  35. Lupe56

    Mahindra 4025 transmission

    I have a mahindra 4025 and I want to know when checking the transmission do I put the dip stick to the start of the threads or screw it in?
  36. F

    Tractor & hoe...Deere 4105, Bota L3800, LS R4041, Mahindra 4025, or?

    Hey everyone. First post...Actually 6th i see as i edit. Don't remember what the heck i posted about previously. Member since 2010. My needs are varied so sorry for long post. I want a compact tractor to do a variety of things. I have rental property. Houses in the city and several small...
  37. V

    Price Check  Mahindra 4025 4wd price check

    Looking to buy a new Mahindra 4025 4wd with the R1 tires. Received a price qoute of $14,750. Sounded like a good price to me but wanted to the opinion of the experts here and see if anyone else has received a qoute lately. vegifarmer
  38. K

    Changing Fuel Filter on a Mahindra 4025

    My fuel jelled on my Mahindra 4025 and was told to change fuel filter and add power service 911 to the fuel. Is it possible to thaw out the filter without replacing it?
  39. C

    Buying Advice  LS 3038 - Mahindra 3535 - Mahindra 4025

    Hello tractor experts, I am looking to add a tractor to the shed and would like to hear of some first hand experience with a couple of these models. So an outline of what I will be expecting out of this new little guy. Started out I wanted a LS 3033 for chores around the farm and bring it to...
  40. T

    Mahindra 4025 4wd no power no start

    I haven't checked anything yet but I figured I'd post here just for ideas what to check when I get home this evening to make the most of what little daylight Ill have. This morning I got up and was taking some hay out to the pasture. The temperature is very mild right now. I let the glow plugs...
  41. R

    New Mahindra 4025 owner

    I just purchased a 2012 Mahindra 4025 2WD at the KS state fair. Sadly the tractor is out of town and I have to wait for the fair to end for it to be delivered. Hoping for early next week. You guys understand a man and his new toy. I have had 2 old tractors. An old AC and a Ford 3000. Finally...
  42. R

    New Mahindra 4025 4wd!

    I traded my 3616 cab for a new 4025 4wd! I got it with a loader and R1 tires. The guys at Artec flipped the tires to make it as wide as possible since there isn't a flat spot on my land. They also loaded the tires and welded some hooks on the bucket for me once I got there for no extra...
  43. R

    Mahindra 4025 vs 5530

    I will start off by saying this my first post. I really have enjoyed reading all of the info on here. Good stuff!!! I have 40 acres that I own and have another 50 I look after for deer hunting. Of the 90 acres, only about 20-25 acres are in pasture/fields/foodplots. The remaining acres are...
  44. M

    Mahindra 4025 won't start

    I am having a problem with my 2wd 4025 - it will not start - the range interlock appears not to be functioning as the key does nothing when turned - battery full charged, fuel good, oil level good and clean oil. When starting the 4025 it is necessary to place the range selector in neutral...
  45. G

    Oil & Fuel  Dip sticks and drain plugs on a Mahindra 4025

    OK guys two simple questions that should be in the owners manual. First do you screw in the engine and trany dip sticks to check oil level? Second, I'm about to do the 50 hour filter and screen clean on my Mahindra 4025 trany. Do I see a second trany drain plug need the engine? Thanks
  46. W

    Mahindra 4025

    Just found pic. please dirgard last post thanks:cool2:
  47. W

    Mahindra 4025

    Just got a auxiliry valve kit from Mahindra with no instrction how to install. Kit #E007206864B91 need visual help (pictures):D thanks
  48. C

    Comparison  Mahindra 4025 4wd versus 3535 4wd

    Hey tractor experts, I've just purchased a 13 acre property with a 3 acre pond. Maybe another acre is covered by trees which won't need to be maintained. The rest is open pasture. I'm not going to be doing much farming, although the wife may talk me into planting a small (1 acre) garden. The...
  49. T

    Mahindra 4025 blown hydraulic hose, anybody know what kind this is?

    I cut a tree down yesterday and it fell the wrong direction... so now its across the driveway and I was cutting it up and dragging it into the pasture to burn it. The tree was over 5ft across at the base so this isnt a tree I could drag with the 4 wheeler and a couple weeks a go a kid fell...
  50. H

    New Mahindra 4025 2wd but got questions

    I got my first Mahindra today 4025 w/loader (2wd). tried her out on some brush piles and works great. I do have one question. the exhaust blows down but not very far so it all ends up right back in my face. Has anyone made any modifications to get that darn exhaust out of their face
  51. B

    Kioti DK40SE and DS4110 vs. Mahindra 4025

    Hello everyone, I just bought a Kioti 4WD DK40SE with their free loader (KL-401) program two days ago. Total price out the door, including sales tax was under 20K (5.5 % financing). Originally I was considering buying the Mahindra 4WD 4025 but the Kioti had more standard options and seemed to...
  52. C

    New owner new Mahindra 4025 FEL

    I have looked long and hard trying to use a limited budget to the best effect. I really wanted used, but most equipment of interest was far away. Locally (within 300 miles) did not show a lot of equipment that did not have high hours. Couldn't pull the trigger on any of them. Really wanted...
  53. LlanoLonghorn

    Help with Log Splitter install on Mahindra 4025

    I have a Mahindra 4025 with a FEL. My question is how do I hook up a TSC 3-Point Hitch Log Splitter. I have never done anything with hydraulics before.
  54. J

    Price Check  mahindra 4025

    Thinking of trading my 2000 ford w/ select-o-speed tranny in on a 4025. I will pay cash and they tell me The differnce will be $8,000 ....Good deal?
  55. C

    Pat's Easy Change System For Mahindra 4025

    Just wanting to know if anyone has used Pat's System on a 4025?
  56. T

    Mahindra 4025 Top Link

    So I'm going to hook up a post hole digger that direct connects without the top link bar. The post hole digger is cat-1, but the top link pin that comes standard is cat-2. The cat-1 pins go right through the big cat-2 hole, but I have to have cat-1 connectivity to hook up the boom pole...
Top