tilt

Many directional valves advertise built-in load checks. Are these as effective as the standard double-pilot operated check valve typically hard-lined directly to the cylinder of top & tilts? Obviously putting the check at the directional valve will introduce a minor amount of bounce to the...

Typical top&tilt cylinders use a normal Double Pilot-operated check to prevent drift. Dark blue Valve1 in the picture. All these uber-compact double check valves use internal pilots for the obvious reason of size & cost. However, if one exposed the pilots (eg "remote" or "external"), then...

Any one own one of these $350 chinese tilt buckets for there mini? I assume il have to adapt the hoses to some US standard? This is going on my 1990 KH-41. I have a chinese quick coupler coming for it also.

I'm going to be needing a trailer soon for hauling my stuff up to Oregon, and then for use there. Tractor, implements, UTV, splitter, etc. Also I plan to be needing a trailer there for hauling cars, tractors and implements, moving hay, and hauling long or unwieldy stuff like irrigation pipe. But...

Has anyone replaced the non-tilt steering column with a tilt steering column on a current production JD 3E series tractor? If so, do you have a parts list and approximate cost? Alternatively, has anyone fabricated a bracket to allow the seat to slide rearward a couple more inches? The fuel tank...

Hi Y'all, just found & joined this community. My problem: I'm adding hyd top & side links with a Vevor 2 spool joystick control valve. I installed a power beyond sleeve into the N port of the valve and it's connected to the +P on the tractor. The P & T ports are connected to the -P & T on the...

This is probably a dumb question.....but I don't know the answer so hopefully someone can help me out. I am seriously considering adding Top and Tilt to my Kubota L2501. I used to have a Quick Hitch (triangular frame), but I gave it away because it was so difficult to hook implements up (too...

It’s been a long time since I’ve been on this site. The old 410 has served me well but one of the tilt cylinders on the loader is now leaking. I rebuilt them many years ago but I’ll be darned if I remember how to take it apart. I know the bucket end unscrews but I think there’s a lock pin...

Do these 15 hp Excavators have the power, weight and ability to handle a tilt grade bucket for ditching and cleaning ditches?

Ok.. I’ve been looking all over for a side link and it appears that I’ve totally missed the bus. My fixed side link is 19 or 20 inches depending on which hole I use on the fork. As I understand the use of a side link, it would be best to have 4-5 inches of movement at least…. Some have said...

If I swap the hoses the bucket tils but then the lift does not work,

Suddenly the hydraulics for the bucket loader do not work at all no up or down or tilt.. Is it the joy stick? It moves easily left and right, up and down. I checked the pot switch for continuity and it passed.. Where do I look next?

Hey Guys - Getting an odd intermittent problem on my 2014 G series. My arm lift and tilt up are become very slow - no power to lift at times - but the problem has come and gone intermittently. Everything tilts down / lowers just fine. I also have no problem with drive. Is there something...

I need to replace all of my lines on the top & tilt spool (Gearmore). The tractor is New Holland compact TC24DA. Can anyone recommend a good source for the hydraulic lines? I’ve reached out to Gearmore but they have not responded.

Anyone else who has the 232h or 242h have a lot of "up and down" play in the steering wheel? Just bought the tractor yesterday and noticed it as soon as I got home. Side to side is good but up and down is pretty sloppy.

After owning my TC34DA for 17 years my steering wheel is flopping up and down and not locking in properly. Have read this is a common problen with these compact New Holland's. Anyone on this forum already went through this and have some install tips to share?

2006 tool cat. tilt slowly drifts down with engine off or running. cylinder seals replaced twice shows no damage. Is this a spool problem or could it be relief valve or spool lock valve. anyone replaced either the spool or valves and had success?? thanks coqui

Hi! I would like to add rear hydraulics and controls for top and tilt. Tractor has a FEL. What do I need to accomplish this and where do I pipe (or) hose it too? Thanks in advance for any advice! Gary

I really don't adjust my tilt steering very often, as evidenced by the fact that I recently tried to pull up on the lever to adjust and it was frozen solid. I sprayed it with penetrating oil and waited about 24 hours before trying again. Guess I tried a little too hard because something behind...

Looks like it would be handy for grading slopes or crowning a road...

Anyone using a lithium battery on their tilt or dump trailer? How do they perform? I’m considering one for my recently purchased tilt trailer.

Bit of a long shot as I don't suppose there are many owners of these on here, however worth asking. I've recently acquired one of these brand new and very cheap on account of the Hydraulic cylinder operating the tilt having been replaced by a Cat 2 top link. Easy solution is replace it with a...

Removed the front end loader from 1025r. Re-installed 2 hours later. Now, when I try to tilt the bucket down, it comes up. Hoses are connected properly.

I’m in the market for a new 20’ trailer for my Kubota L6060. It gets moved a handful of times a year. I’m leaning towards an aluminum trailer this time, and I like the looks and longevity of an aluminum deck. I’m also considering a full tilt on this one. Is an aluminum deck really more...

The lift arms and tilt lock up on my 2015 Compact Tracked Loader after 15 - 30 minutes of operation while using a bucket or auger attachment. The only fault code displayed is M3507 (Hydraulic fan open circuit), usually displaying after 2 - 5 minutes of operation. The fan is turning and the...

The lift arms and tilt lock up on my 2015 Compact Tracked Loader after 15 - 30 minutes of operation while using a bucket or auger attachment. The only fault code displayed is M3507 (Hydraulic fan open circuit), usually displaying after 2 - 5 minutes of operation. The fan is turning and the...