Adding hydraulics to a sickle bar mower

   / Adding hydraulics to a sickle bar mower #11  
Pic.#2
 

Attachments

  • 742277-2005_0923Image0018.JPG
    742277-2005_0923Image0018.JPG
    89 KB · Views: 681
   / Adding hydraulics to a sickle bar mower #12  
Pic.#3
 

Attachments

  • 742280-2005_0923Image0019.JPG
    742280-2005_0923Image0019.JPG
    80.4 KB · Views: 644
   / Adding hydraulics to a sickle bar mower #13  
Last one #4. If you do this this I would advise using flow restricters on both sides of the cylinder.I used 1/16 flow restricters on my IH1300 after I found that under normal operating pressure the cutter goes up and down extremly fast. I really like this setup, On my IH1300 you can control the cutter to cut horizontal or vertical or anywhere in between. This makes it nice for cutting back brush up to 1" diameter on trails or along roads. /forums/images/graemlins/grin.gif /forums/images/graemlins/grin.gif

Bernie
 

Attachments

  • 742284-2005_0923Image0020.JPG
    742284-2005_0923Image0020.JPG
    89.9 KB · Views: 630
   / Adding hydraulics to a sickle bar mower #14  
Thanks Bernie…
I was thinking of something along that line … I may have to make some type of ‘cam-over’ arrangement to allow a steep negative angle, as along a ditch. What cylinder length is that? KennyV.
 
   / Adding hydraulics to a sickle bar mower
  • Thread Starter
#15  
Excellent work Bernie. It looks like where your cylinder is mounted that would take the place of the spring on the New Holland. How long of a cylinder is that? Here is some pictures of the mower. Paint job is badly needed.
 

Attachments

  • 742337-DSCF0001f (Small).JPG
    742337-DSCF0001f (Small).JPG
    90.5 KB · Views: 568
   / Adding hydraulics to a sickle bar mower
  • Thread Starter
#16  
Pic 2 oops same picture /forums/images/graemlins/grin.gif
 

Attachments

  • 742342-DSCF0001f (Small).JPG
    742342-DSCF0001f (Small).JPG
    90.5 KB · Views: 387
   / Adding hydraulics to a sickle bar mower
  • Thread Starter
#17  
Next one
 

Attachments

  • 742345-DSCF0002f (Small) (Small) (WinCE).JPG
    742345-DSCF0002f (Small) (Small) (WinCE).JPG
    23.6 KB · Views: 450
   / Adding hydraulics to a sickle bar mower
  • Thread Starter
#18  
another
 

Attachments

  • 742346-DSCF0003f (Small) (WinCE).JPG
    742346-DSCF0003f (Small) (WinCE).JPG
    23.5 KB · Views: 412
   / Adding hydraulics to a sickle bar mower #19  
This cylinder is 2" with a 16" stroke. It took the place of a 5/8 curved rod. I had to measure with the cutter up and down then figure what cylinder to use.

Bernie
 

Tractor & Equipment Auctions

2006 International 4400 LP Ambulance (A50323)
2006 International...
2019 GENIE Z-45/25XC V2 TELESCOPIC MANLIFT (A51242)
2019 GENIE...
Flatbed Body for Heavy Truck (A50854)
Flatbed Body for...
2002 Ford F-150 4x4 Ext. Cab Pickup Truck (A50323)
2002 Ford F-150...
2016 Kawasaki 70 TM 7 Articulating Wheel loader (A51039)
2016 Kawasaki 70...
2009 JACK COUNTY 130 BBL VACUUM  TRAILER (A50854)
2009 JACK COUNTY...
 
Top