Adding hydraulics to a sickle bar mower

   / Adding hydraulics to a sickle bar mower #11  
Pic.#2
 

Attachments

  • 742277-2005_0923Image0018.JPG
    742277-2005_0923Image0018.JPG
    89 KB · Views: 680
   / Adding hydraulics to a sickle bar mower #12  
Pic.#3
 

Attachments

  • 742280-2005_0923Image0019.JPG
    742280-2005_0923Image0019.JPG
    80.4 KB · Views: 643
   / Adding hydraulics to a sickle bar mower #13  
Last one #4. If you do this this I would advise using flow restricters on both sides of the cylinder.I used 1/16 flow restricters on my IH1300 after I found that under normal operating pressure the cutter goes up and down extremly fast. I really like this setup, On my IH1300 you can control the cutter to cut horizontal or vertical or anywhere in between. This makes it nice for cutting back brush up to 1" diameter on trails or along roads. /forums/images/graemlins/grin.gif /forums/images/graemlins/grin.gif

Bernie
 

Attachments

  • 742284-2005_0923Image0020.JPG
    742284-2005_0923Image0020.JPG
    89.9 KB · Views: 629
   / Adding hydraulics to a sickle bar mower #14  
Thanks Bernie…
I was thinking of something along that line … I may have to make some type of ‘cam-over’ arrangement to allow a steep negative angle, as along a ditch. What cylinder length is that? KennyV.
 
   / Adding hydraulics to a sickle bar mower
  • Thread Starter
#15  
Excellent work Bernie. It looks like where your cylinder is mounted that would take the place of the spring on the New Holland. How long of a cylinder is that? Here is some pictures of the mower. Paint job is badly needed.
 

Attachments

  • 742337-DSCF0001f (Small).JPG
    742337-DSCF0001f (Small).JPG
    90.5 KB · Views: 567
   / Adding hydraulics to a sickle bar mower
  • Thread Starter
#16  
Pic 2 oops same picture /forums/images/graemlins/grin.gif
 

Attachments

  • 742342-DSCF0001f (Small).JPG
    742342-DSCF0001f (Small).JPG
    90.5 KB · Views: 386
   / Adding hydraulics to a sickle bar mower
  • Thread Starter
#17  
Next one
 

Attachments

  • 742345-DSCF0002f (Small) (Small) (WinCE).JPG
    742345-DSCF0002f (Small) (Small) (WinCE).JPG
    23.6 KB · Views: 449
   / Adding hydraulics to a sickle bar mower
  • Thread Starter
#18  
another
 

Attachments

  • 742346-DSCF0003f (Small) (WinCE).JPG
    742346-DSCF0003f (Small) (WinCE).JPG
    23.5 KB · Views: 411
   / Adding hydraulics to a sickle bar mower #19  
This cylinder is 2" with a 16" stroke. It took the place of a 5/8 curved rod. I had to measure with the cutter up and down then figure what cylinder to use.

Bernie
 

Tractor & Equipment Auctions

2015 International DuraStar 4300 Street Sweeper Truck (A50323)
2015 International...
2016 FREIGHTLINER CASCADIA TANDEM AXLE 6X4 MID ROOF SLEEPER TRUCK (A51219)
2016 FREIGHTLINER...
UPDATED INTERNET BUYER'S PREMIUM TERMS (A50775)
UPDATED INTERNET...
2017 Caterpillar 259D Two Speed Compact Track Loader Skid Steer (A50322)
2017 Caterpillar...
71059 (A49346)
71059 (A49346)
TAKEUCHI TL150 SKID STEER (A51242)
TAKEUCHI TL150...
 
Top