Adding hydraulics to a sickle bar mower

   / Adding hydraulics to a sickle bar mower #11  
Pic.#2
 

Attachments

  • 742277-2005_0923Image0018.JPG
    742277-2005_0923Image0018.JPG
    89 KB · Views: 680
   / Adding hydraulics to a sickle bar mower #12  
Pic.#3
 

Attachments

  • 742280-2005_0923Image0019.JPG
    742280-2005_0923Image0019.JPG
    80.4 KB · Views: 643
   / Adding hydraulics to a sickle bar mower #13  
Last one #4. If you do this this I would advise using flow restricters on both sides of the cylinder.I used 1/16 flow restricters on my IH1300 after I found that under normal operating pressure the cutter goes up and down extremly fast. I really like this setup, On my IH1300 you can control the cutter to cut horizontal or vertical or anywhere in between. This makes it nice for cutting back brush up to 1" diameter on trails or along roads. /forums/images/graemlins/grin.gif /forums/images/graemlins/grin.gif

Bernie
 

Attachments

  • 742284-2005_0923Image0020.JPG
    742284-2005_0923Image0020.JPG
    89.9 KB · Views: 629
   / Adding hydraulics to a sickle bar mower #14  
Thanks Bernie…
I was thinking of something along that line … I may have to make some type of ‘cam-over’ arrangement to allow a steep negative angle, as along a ditch. What cylinder length is that? KennyV.
 
   / Adding hydraulics to a sickle bar mower
  • Thread Starter
#15  
Excellent work Bernie. It looks like where your cylinder is mounted that would take the place of the spring on the New Holland. How long of a cylinder is that? Here is some pictures of the mower. Paint job is badly needed.
 

Attachments

  • 742337-DSCF0001f (Small).JPG
    742337-DSCF0001f (Small).JPG
    90.5 KB · Views: 567
   / Adding hydraulics to a sickle bar mower
  • Thread Starter
#16  
Pic 2 oops same picture /forums/images/graemlins/grin.gif
 

Attachments

  • 742342-DSCF0001f (Small).JPG
    742342-DSCF0001f (Small).JPG
    90.5 KB · Views: 386
   / Adding hydraulics to a sickle bar mower
  • Thread Starter
#17  
Next one
 

Attachments

  • 742345-DSCF0002f (Small) (Small) (WinCE).JPG
    742345-DSCF0002f (Small) (Small) (WinCE).JPG
    23.6 KB · Views: 449
   / Adding hydraulics to a sickle bar mower
  • Thread Starter
#18  
another
 

Attachments

  • 742346-DSCF0003f (Small) (WinCE).JPG
    742346-DSCF0003f (Small) (WinCE).JPG
    23.5 KB · Views: 411
   / Adding hydraulics to a sickle bar mower #19  
This cylinder is 2" with a 16" stroke. It took the place of a 5/8 curved rod. I had to measure with the cutter up and down then figure what cylinder to use.

Bernie
 

Tractor & Equipment Auctions

2013 COACHMEN CATALINA TRAVEL TRAILER (A50854)
2013 COACHMEN...
2009 PETERBILT 388 TANDEM AXLE DAY CAB (A51219)
2009 PETERBILT 388...
2007 FORD F-450 (A50854)
2007 FORD F-450...
2018 INTERNATIONAL LT625 TANDEM AXLE DAY CAB (A51219)
2018 INTERNATIONAL...
2017 JCB 3CX 15HFCE BACKHOE (A51242)
2017 JCB 3CX...
2015 JOHN DEERE 744K-II HIGH LIFT WHEEL LOADER (A51242)
2015 JOHN DEERE...
 
Top