Help Identifying Tiller

[BodeMiller]

Can anyone here help me identify what brand/model tiller this is? Thanks.

 

[paulsharvey]

Yes — from the photos, that appears to be an older Howard Rotavator (or possibly a Lely or Ford-branded version of the same machine). Here are the key identifiers that point toward a Howard Rotavator:

Distinctive gearbox shape and side cover – the large rounded gearbox housing with the bolt-on access plate is a hallmark of Howard tillers from the 1960s–1980s.

Heavy-duty chain drive housing – Howard used an oil-bath chain case on one side (as seen in your photo) rather than a gear drive, which matches that large bulged cover and filler plug.

Adjustable tailboard and depth skids – the rear panel with side plates and chain support are classic Howard design elements.

Three-point hitch configuration and PTO shaft setup – the overall geometry matches Howard’s “HR,” “Rotavator E,” or “Rotavator 60/70” models.

Likely model

It looks most like a Howard Rotavator HR30 or HR40, depending on the width (around 60–80 inches wide).
If you measure the working width and find a tag or stamped number on the gearbox housing, it can confirm the exact model.
Common models from this era include:

HR30 – ~60" tilling width

HR40 – ~80" tilling width

Rotavator 70 series – similar build but newer decal style


Notes

These units are PTO-driven (540 rpm), chain-drive tillers, very durable, and still serviceable.

Gearbox oil and chain case oil should be checked or replaced before use.

Howard was originally a British company (later acquired by Daken/Howard Australia and CNH).


If you can find a data plate (often on top of the gearbox or left-hand side near the hitch frame) or give me the overall width, I can narrow down the model exactly.

 

[paulsharvey]

Thats just uploading your imagines to Chat, so, the next step, I would pull data on the HR30 and HR40, and look for similarities/differences, and see if its right

 

[TractorTech]

Welcome to TBN!

I disagree. Not Howard and not Ford as the early ones were RH chain boxes. Later were LH gear driven side box. The center gearbox and top frame not Howard.
It could be a Maletti, Bushhog, not sure though.
What width is it? It looks 60-65". What kind of blades on it? C or L style? Are there part numbers on the blades or a casting number on the center gearbox anywhere?

 

[BodeMiller]

Yes — from the photos, that appears to be an older Howard Rotavator (or possibly a Lely or Ford-branded version of the same machine). Here are the key identifiers that point toward a Howard Rotavator:

Distinctive gearbox shape and side cover – the large rounded gearbox housing with the bolt-on access plate is a hallmark of Howard tillers from the 1960s–1980s.

Heavy-duty chain drive housing – Howard used an oil-bath chain case on one side (as seen in your photo) rather than a gear drive, which matches that large bulged cover and filler plug.

Adjustable tailboard and depth skids – the rear panel with side plates and chain support are classic Howard design elements.

Three-point hitch configuration and PTO shaft setup – the overall geometry matches Howard’s “HR,” “Rotavator E,” or “Rotavator 60/70” models.

Likely model

It looks most like a Howard Rotavator HR30 or HR40, depending on the width (around 60–80 inches wide).
If you measure the working width and find a tag or stamped number on the gearbox housing, it can confirm the exact model.
Common models from this era include:

HR30 – ~60" tilling width

HR40 – ~80" tilling width

Rotavator 70 series – similar build but newer decal style


Notes

These units are PTO-driven (540 rpm), chain-drive tillers, very durable, and still serviceable.

Gearbox oil and chain case oil should be checked or replaced before use.

Howard was originally a British company (later acquired by Daken/Howard Australia and CNH).


If you can find a data plate (often on top of the gearbox or left-hand side near the hitch frame) or give me the overall width, I can narrow down the model exactly.

Awesome info. Thanks. The only thing I can find on it is a sticker D72. I’m borrowing it from a neighbor and it stopped functioning. The tiller isn’t moving but the PTO drive seems to be going. Thoughts?

 

[BodeMiller]

Here are the tines.

 

[CH4Ohio]

Sounds like a shear-bolt. Find where it’s slipping and replace the bolt.

If the gearbox is turning, then need to check for broken chain.

 

[TractorTech]

Awesome info. Thanks. The only thing I can find on it is a sticker D72. I’m borrowing it from a neighbor and it stopped functioning. The tiller isn’t moving but the PTO drive seems to be going. Thoughts?

So the drive is moving? With the tractor off, can you move the rotor that holds the tines? Does it have a PTO slipclutch or shearbolt on the driveline?

 

[BodeMiller]

When I free spin the PTO shaft the chain rotates but the tine shaft(?) doesn’t. When I spin the tine shaft the chain doesn’t move. I can hear a sound of what may be the chain slipping past a sprocket. I don’t see a shear pin anywhere. Also, have a bad seal it seems.

 

[TractorTech]

Well if you hear the chain slipping past a sprocket, you'll have to remove the side gearbox cover. You may find part numbers on the sprockets. The seal will have its own number and can be procured through a bearing shop.
You will also be able to tell original color of the tiller when you remove the gearbox cover. However, most were originally orage, but it may help determine manufacturer.