MAX-24-Dean
Veteran Member
The Splitfire I use has about a 4 second cycle time. makes for some fast splitting if the wood grain is straight, which most is. The only problem is to keeping up with the splitter it takes two people to move the wood.
Need a recommendation: log splitters
- Thread starter beowulf
- Start date
- Views: 14006
-
- Tags
- log recommendation
Farmer495
Veteran Member
15.4 GPM pump on tractor running wide open will keep three men busy and the wedge never stops
terraformer
Silver Member
Our biggest pieces are sometimes 20-24" diameter and are too heavy to lift so vertical mode is a must.
This is a typical pile of wood by fall.
This is a typical pile of wood by fall.
Slowpoke Slim
Elite Member
- Joined
- Jan 6, 2017
- Messages
- 3,610
- Location
- Bismarck, ND
- Tractor
- Husqvarna YTH24V48 riding mower, Branson 3725CH
I just have a cheap "homeowner grade" splitter myself. It will go vertical or horizontal, but I've never tried it in the vertical mode. Like others have said, I need to work while standing and not bending over and wrestling rounds on the ground to split. Picking a round up off the ground to set on the table isn't near as bad as long term bending over to work the splits on the ground. Most of the time I have the pre cut rounds sitting in my fel bucket at a comfortable height next to me while I'm splitting on the small table. Then I toss the splits into either my garden cart, or hopefully into an IBC tote frame. If I'm lucky and have access to an empty IBC tote, then that will be the last time I have to handle the wood until it's time to carry it from the garage into the house to burn it (I'm fortunate enough to be able to bring a tote all the way into my garage and stage it inside to pick wood from).
My splitter. Nothing to get excited about, but it works...
My splitter. Nothing to get excited about, but it works...
EddieWalker
Epic Contributor
Found another picture of my splitter. I bolted on some plywood to the sides to hold the wood that I'm not splitting. I split it in half, put one half on the plywood, work the other half, then work that first half.
If it's a really big round, I might drop the half to the ground, and then split the other half and put that quarter on the plywood. I try to avoid messing with really big rounds, they wear me out.
If it's a really big round, I might drop the half to the ground, and then split the other half and put that quarter on the plywood. I try to avoid messing with really big rounds, they wear me out.
ultrarunner
Epic Contributor
- Joined
- Apr 6, 2004
- Messages
- 23,668
- Tractor
- Cat D3, Deere 110 TLB, Kubota BX23 and L3800 and RTV900 with restored 1948 Deere M, 1949 Farmall Cub, 1953 Ford Jubliee and 1957 Ford 740 Row Crop, Craftsman Mower, Deere 350C Dozer 50 assorted vehicles from 1905 to 2006
I can’t lift but have a long reach so bringing the rounds to the splitter with the loader and then reach and roll with splitter vertical works well for me…
A few are so big I could never lift and it’s all I can do to roll but the 22ton spitter takes all the Coast Oak I can get under the wedge.
A few are so big I could never lift and it’s all I can do to roll but the 22ton spitter takes all the Coast Oak I can get under the wedge.
terraformer
Silver Member
We have a round about 10" high that we squat on and work the machine vertical. Have a foam pad. My wife and I tag team. One person throws the wood and keeps unsplit close at hand for the other who is doing the splitting.
Repeated lifting of 100 pound (or even 50 pound) rounds are not a good solution for us.
Repeated lifting of 100 pound (or even 50 pound) rounds are not a good solution for us.
dodge man
Super Star Member
I also sit on a round when splitting vertical. I also keep an axe handy if you have one that is a little stringy. It seems easier to roll a large round to the splitter and the flip it on end and rock it into position than noodling or lifting a heavy one up with the end loader.
aesanders
Platinum Member
- Joined
- Aug 12, 2005
- Messages
- 981
- Location
- Alachua County, Florida
- Tractor
- LS MT3 42 S HST cab, BCS 830 2 wheel tractor, Gravely Pro-Turn 160 XDZ, John Deere Gator HPX 615e
So, Beowulf, did you ever decide on a new log splitter?
The new log splitter bug has hit me with a vengeance. Really liking the looks of Wolfe Ridge splitters. Maybe a 28 pro model. Eastonmade Ultra looks really nice as well. Both are overkill for my needs, but I believe I want a quality splitter, that will last the rest of my life.
Split fire has a new small verticals model. 1165v that looks really nice also. Decisions, decisions……
The new log splitter bug has hit me with a vengeance. Really liking the looks of Wolfe Ridge splitters. Maybe a 28 pro model. Eastonmade Ultra looks really nice as well. Both are overkill for my needs, but I believe I want a quality splitter, that will last the rest of my life.
Split fire has a new small verticals model. 1165v that looks really nice also. Decisions, decisions……
He said on page 2 of the posts he pulled the trigger on a Champion 27.
We have just finished putting another year on ours. Filled 12 totes stacked over the top so 4 cord. It didn't seem to care at all no issues. Engine oil change is a nothingburger, only about 1qt. Usually starts first pull.
The Wolf Ridge are beautiful and look well made, but their cost is kind of out there. I think their cheaper horizontal units are getting close to the cost of an entire import firewood processor with a lot of options that will saw for you and has conveyors.
We have just finished putting another year on ours. Filled 12 totes stacked over the top so 4 cord. It didn't seem to care at all no issues. Engine oil change is a nothingburger, only about 1qt. Usually starts first pull.
The Wolf Ridge are beautiful and look well made, but their cost is kind of out there. I think their cheaper horizontal units are getting close to the cost of an entire import firewood processor with a lot of options that will saw for you and has conveyors.
