Welding in Haiti

   / Welding in Haiti #21  
No worrys about stealing but I am careful with the tools that I have to have. That's because the Haitians are just like helpers anywhere, they don't take care of tools like us guys do.
A little off topic, but sad, and funny: A pump installer loaned a pipe wrench to my ex-landlord. Upon returning it, he noticed a wad of clay on his boot, and used the upper jaw of the wrench to scrape off sticky mud. I now own the property this happened on.
 
   / Welding in Haiti
  • Thread Starter
#22  
Today we went into Cite Soliel to Jeremy Wharf. I took some photos of a couple welding shops, some of their equipment, and the men.

What is going to be fun is next week we'll be taking one of the machines we built down there and using it. It will be a chance for them to see what we can do too.

the internet connection isn't allowing me to upload the photos at this time. I'll try in the morning.
 

Attachments

  • 019.JPG
    019.JPG
    112.8 KB · Views: 289
  • 027.JPG
    027.JPG
    118.6 KB · Views: 271
  • 028.JPG
    028.JPG
    116.1 KB · Views: 278
  • 029.JPG
    029.JPG
    121.4 KB · Views: 292
Last edited:
   / Welding in Haiti #23  
Today we went into Cite Soliel to Jeremy Wharf. I took some photos of a couple welding shops, some of their equipment, and the men.

What is going to be fun is next week we'll be taking one of the machines we built down there and using it. It will be a chance for them to see what we can do too.

the internet connection isn't allowing me to upload the photos at this time. I'll try in the morning.

Harvey,:)
You are my hero. I can not even tell my son what to do effectively, much less strangers. You are a true teacher.
hugs, Brandi
 
   / Welding in Haiti
  • Thread Starter
#24  
If you look at a welding machine and wonder why it costs so much this might help you justify the costs.

If you look at the last photo you will see the amperage adjustments.
 

Attachments

  • 015.JPG
    015.JPG
    95.7 KB · Views: 284
  • 016.JPG
    016.JPG
    109.3 KB · Views: 305
  • 017.JPG
    017.JPG
    107.2 KB · Views: 274
  • 018.JPG
    018.JPG
    119 KB · Views: 372
   / Welding in Haiti #25  
Hats off to you Harvey. :thumbsup:
 
   / Welding in Haiti
  • Thread Starter
#27  
Any updates to this thread?



Mr. HE:cool:

I've been home 30 days today, gained back half of the weight I lost in the thirty days I was in Haiti.

The UN is contributing some start up money for training and I am here in the States fund raising to go back and do a pilot project. I left two working machines in Haiti. Grass Roots United gives demonstrations daily on making the blocks.

One of the things that I promised myself was that I would try to do something for the street welders in Haiti that do their welding/tacking wearing only sunglasses.

What we are doing is purchasing shade ten lenses and carrying them in our luggage. If we buy the cheapest hoods available it will cost us about $20.00 each after freight. Then there is the customs issues, six months isn't unheard of. We can carry hundreds of lenses in our luggage and give them out along with instructions for making their own hoods using common materials. Doing this we can provide three hundred street welders eye protection for the same amount that it will cost us to give ten of them the cheapest hoods we can buy here in the States.

Keep in mind the street welders aren't doing the kinds of welding we do here in shops etc. They are basically tacking everything together. They aren't laying down multiple passes using lots of amps. Regular welding shops have the hoods etc. It's the street welders that we are seeking to help.

I can buy the shade ten lenses for less than a dollar each. We have a volunteer that is interested in walking the streets of Haiti giving out lenses and instructions for making a hood out of cardboard and duct tape. This is less than ideal but we have to weigh the amount of good this can do versus the cost of just helping a select few. The life expectancy of a Haitian male is around fifty years. The last twenty of those can be blind or not experienced if they don't have a family to support them.

My position on aid is we are obligated to help with knowledge at a minimum. I personally believe that teaching them to build their own hoods and encouraging them to be responsible for their own protection is better than handing them a hood and walking away. Then there's the welder thing, you know it, prideful buggers, welders. I believe that if they get the chance to make their own hoods they will individualize it. It doesn't take much imagination to see welding hoods as art in no time at all.

This is in the forming stages right now. We hope to have something on the ground by the end of October.
 
   / Welding in Haiti
  • Thread Starter
#28  
Here's some numbers for you on our blocks and houses.

Haitian house, 240 sq ft, $4.000.00 to $4,500.00. Only $1,500.00 of that is for materials and that is purchased locally. Each house injects $2,500 to $3,000.00 into the local community in wages. The material costs are for Portland cement, sand, gravel, rebar, and wire along with a door and some windows. The house is plastered inside and out and we now have a concrete roof as part of the design. The concrete appearance is critical. One of the big obstacles all the geniuses who have designed the thirty to seventy thousand dollar minimalist homes for Haiti is they have ignored cultural wisdom that teaches nothing survives Haitian conditions like concrete, except in an earthquake of course. The experts not only have to sell the affordability, there is no shortage of upper middle class housing, they face convincing Haitians that stuff that works in Canada, France, or the United States will work just as well in Haiti when experience has taught them otherwise.

Each house removes approximately 1/2 of a forty foot shipping container's contents worth of foam and film plastics from the landfill and landscape.

We are raising funds for a shake table test by NTS in Plano, Texas. They will take the building that we built for SMU last April that has been waiting for a testing slot at OU since the first of May and place it on their shake table. Day one will be a test that will simulate 15 to 20 years normal wear and tear. Day two will do earthquake tests with the final one simulating a 7.0.

If we survive those tests, I believe it will with minimal damage, the method and house will pass seismic construction standards for everywhere in the world but Japan. The caveat there is Japan might have changed its standards after the last quake and tsunami.

The cost is ten grand. That includes videos and reports.
 
   / Welding in Haiti #30  
Some place we can send some money to help purchase lenses? Do you have a PayPal account?

I think that is a great idea and would like to support it.
 

Tractor & Equipment Auctions

2022 MAXXD BD14 Heavy-Duty Dump Trailer with 14K GVWR and Tandem Axles (A52128)
2022 MAXXD BD14...
David Bradley Manure Spreader (A50515)
David Bradley...
2016 ROADTEC RP-190E ASPHALT PAVER (A51222)
2016 ROADTEC...
2021 CATERPILLAR 259D3 SKID STEER (A51242)
2021 CATERPILLAR...
New JMR 78" Double Skidloader Grapple (A50774)
New JMR 78" Double...
2025 Swict 84in Bucket Skid Steer Attachment (A50322)
2025 Swict 84in...
 
Top