Where's this Grease Fitting?

[Kiohio]

Re: Where\'s this Grease Fitting?

LOL
I had a customer complaining about that very point being "sticky"..
I said "Did you grease it", he said "What?"
I said "I take that as a NO!"
He greased it and worked it.....mucho better!!

KO

 

[Kiohio]

Re: Where\'s this Grease Fitting?

LOL
I had a customer complaining about that very point being "sticky"..
I said "Did you grease it", he said "What?"
I said "I take that as a NO!"
He greased it and worked it.....mucho better!!

KO

 

[Highbeam]

Re: Where\'s this Grease Fitting?

I know, I know, the 3ph pivot. Lame one that overflows out towards the front but I would think it should make it direct grease to the left side or maybe another on the left.

This is great fun.

Now the toughy is the one on the clutch pivot zerc. I can't get it so it is not being greased /forums/images/graemlins/frown.gif

 

[Highbeam]

Re: Where\'s this Grease Fitting?

I know, I know, the 3ph pivot. Lame one that overflows out towards the front but I would think it should make it direct grease to the left side or maybe another on the left.

This is great fun.

Now the toughy is the one on the clutch pivot zerc. I can't get it so it is not being greased /forums/images/graemlins/frown.gif

 

[mrutkaus]

Re: Where\'s this Grease Fitting?

Where is there a diagram of all the grease fittings on the 30?

Mike

 

[mrutkaus]

Re: Where\'s this Grease Fitting?

Where is there a diagram of all the grease fittings on the 30?

Mike

 

[Kiohio]

Re: Where\'s this Grease Fitting?

Take the straight fitting out and put in an angle one.

KO

 

[Kiohio]

Re: Where\'s this Grease Fitting?

Take the straight fitting out and put in an angle one.

KO

 

[TBDonnelly]

Re: Where\'s this Grease Fitting?

<font color="blue"> I know, I know, the 3ph pivot. Lame one that overflows out towards the front but I would think it should make it direct grease to the left side or maybe another on the left.
</font>

Your answer is very close......just needs a little fine tuning.

This grease fitting is accessed from the rear of the tractor. It is on the right side (right as referenced from sitting in the drivers seat). This grease fitting actually has to do with the linkage that attaches to the handle that raises and lowers the 3 point hitch. Hence, if your 3 point hitch handle is stiff or sticky, this is the fitting to grease. This linkage does not cross over to the left side so, no grease fitting is necessary on the left.

In the attached picture you'll see the grease fitting almost centered in the pic. It sits to the right and a bit behind the right 3 point lift arm.

Don

 

[TBDonnelly]

Re: Where\'s this Grease Fitting?

<font color="blue"> I know, I know, the 3ph pivot. Lame one that overflows out towards the front but I would think it should make it direct grease to the left side or maybe another on the left.
</font>

Your answer is very close......just needs a little fine tuning.

This grease fitting is accessed from the rear of the tractor. It is on the right side (right as referenced from sitting in the drivers seat). This grease fitting actually has to do with the linkage that attaches to the handle that raises and lowers the 3 point hitch. Hence, if your 3 point hitch handle is stiff or sticky, this is the fitting to grease. This linkage does not cross over to the left side so, no grease fitting is necessary on the left.

In the attached picture you'll see the grease fitting almost centered in the pic. It sits to the right and a bit behind the right 3 point lift arm.

Don