Search results

This elbow fitting is on the boom cylinder of a Kubota KX040-4. At first glance one might think it's -10 ORB to -6 JIC...But it's not. The hose fitting looks very similar to a NPTF, but the thread diameter is not the same. Most of the hose ends look like they attach to strait thread pipe...

This is from a brand new single acting hydraulic pump, probably Chinese. Documentation really sucks. It works perfectly; i.e. up button turns on pump; down button opens another valve to lower the dump body. But the circuit makes no sense to me. I can see the pump, and check valve. I believe A is...

Have a dump truck with a double acting cylinder. Replacing the pump with a new single acting pump. There’s no place to attach the rod end hose. Can I just take the hose off and leave it open to atmosphere?

Recently changed fuel filters on my L5240 tractor. Now, no matter how tight I tighten the aluminum ring that holds the plastic bowl, it's leaking. It's been perfect for years. I took the bowl off again and wiped both the oring on the bowl and the mating surface it goes to, with no effect. Am i...

Have 2000' gravel driveway built around 2000. The ditches were established and filled with 7" minus. Now they're filled with sediment from the hillsides, as well as with quite a bit of "hard pack" (local term for crushed rock with the fines left in). Have Kubota KX-040-4 with a good ditch...

Have an old bush hog; about 5 foot. Thinking of building an adapter to go on the end of my KX 040 excavator. Have about 17 GPM I think; not sure of the pressure. If I were to direct drive where the PTO connected, what kind of hydraulic motor would I need to turn five or 600 RPM(pto speed)? Is...

For a few years I struggled with putting the rear chains on my Kubota 5240. Not having help, or a crane, or another tractor with a loader didn't help the situation. Finally I came up with this simple method. It does demand a barn, garage or other structure for your tractor. It works fabulously...

I'm getting a Bauman 1040B drop spreader that looks like it has a manual flow control valve similar to the kind on Northern Tool...I think it's by Brand Hydraulics. See attached. I'm using the front hydraulics the valve for which is a center off spool (push button actuated from the cab). I can...

SAND AND SALT SPREADER - Pronovost Trying to figure out how big the sand aggregate can be put through it. Our town buys material that has pieces 1/4" or so. Not sure a drop spreader like this can handle it. Anyone have one of these or similar?

I bought the filter on the left from Messicks ages ago, intending to replace it in my L5240. But when I extracted the filter the previous owner had installed, it looked nothing like the Messicks recommended filter. It was actually a John Deere filter! Go figure.I really wish the Kubota Operators...

Thinking of getting a Quick Hitch. Have Cat 1/2 tractor; and all four implements come close to the standard28" center to center lower lift dims. But the vertical pin to pin dimension of both Cat1 and Cat2 Quick hitches seems to be 15" and change (some, like titan go from 14-17 1/2). But my...

Have a Land Pride LR3784 Rake. With winters warming up, I've had to remove my Pronovost Rear Pull Blower several times each spring (and occasionally in the fall before the ground freezes), and replace it with the rake to move the "slush". It's too heavy for anything but solid frozen ground and...

Been using Rotella 5w40 synthetic. Just noticed Rotella makes a 0w40. How cold is cold enough to go to the 0w40? Manual calls for 5w40 but it was probably written before 0w40 even existed lol. Advice appreciated.

Having an excavator guy come this fall to build several terrace walls of big stones I have about 150' away from where they'll be used. He could probably ferry them from yonder but want to stockpile them close to where they'll be used. Most, I can't lift with the FEL (grapple claw), but can roll...

Kubota L5240HST. Getting ready for a filter change all around. Read the owners manual and see the two "hydraulic" filters. Or I should say one is a "transmission" filter and the other is a "hydraulic" filter (I think the hydraulic one is on the right forward of the step, the transmission one on...

Adding two channels of rear hydraulics on my Kubota 5240. I've read that, depending on the tractor/top'n'tilt system, some restriction or flow control may be needed to slow down the adjustments. My background is more industrial hydraulic related, and we've often "metered out" such systems...

I'm running my blower chute motor from the third function ports on the loader arm. Before next winter, I'll be getting a sander with a similar size motor (8gpm). I'll never be blowing and sanding at the same time. What kind of "two channel" valve should I use that will simultaneously switch the...

I was at a John Deere dealer and saw a rear hydraulic setup wherein there was a handle operated cam thing that connected both hoses at once. Does anyone know if there is an "after market" option to install these on a tractor (not a John Deere, lol). I use both Flat Face and Ag, but would switch...

I have the third function hydraulics on a kubota 5240 to run a grapple claw et. al. Considering putting a Hardy 54" sander with a quick attach bracket on the loader. The sander does not state hydraulic requirements. I do run a hydraulic motor on it to turn the chute on my snowblower, but wonder...

I've know, with pretty good precision, How long the top link needs to be when attached to the snow blower, the rake, the mower etc. But, short of getting a tape measure out to measure the exposed threads, or making a bunch of gauges, Does anyone know of a way to paint or otherwise mark the...

I've searched and read a ton of threads on "Position Control", "Draft Control", and they all seem to imply that the hydraulics can apply up pressure lifting the implement, but gravity is all you got going for you going down. I believe my tractor (Kubota L5240) has Position Control but not Draft...

Well, it finally happened. I was blowing my 1500' drive (steep, curvy) with the K5240, when I noticed the right front tire was going flat. Haven't figured out why yet (the tire is still at the shop; I suspect low tire pressure), but proceeded about 50' to one of the only turnarounds on the...

Whenever it's below freezing, my third function valve sticks until enough warm oil goes through it (usually as much as 45 minutes, by which time I'm nearly done blowing). It typically goes end to end once the button in the cab is pressed; I'm sure it's not an electrical problem. I chalked it up...

What kind of shackles do folks use to hold rear tire chains on? I've tried regular "D" shackles, but the pins get all mushed if they're pointing out (the flat blade that you tighten the pin with), and I'm worried they'll cut into the tire if pointing in. The links are twisted, so I can't really...

We've had so much slushy wet snow with unfrozen ground, I've had to put my landscape rake back on the tractor which I find works great for 2-4" of wet snow. I recently added the "drop down" grader blade and tried it and need advise from someone who owns and has used one. When the blade drops...

Forgive the newbie question; I did a search and could not come up with a good hit. Just sold our HLA plow and bought a used Provenost P-INV 80 Reverse pull blower for our Kubota 5240. We've had one heck of a November with repeated dumps (some small, some big) of wet slop. Based on experience...

My experience is primarily with pneumatic actuators. To slow them down we typically "meter out", that is, put the flow control on the return line to the valve. Trying to slow down a snow blower chute turn hydraulic motor. Is it proper to control the flow into each line, or out of each line...

Just about ready to pull the trigger on a used Pronovost P-inv80 rear pull blower. I thought at first it required 40 to 70 hp tractor, but I just read the specs again and it says "40-70 hp PTO". I've read that the PTO horsepower is lower than the tractor, and can't find the numbers in the...

Does anyone know of the proper size grease zert that is used on Kubota FELs. They look a tiny bit smaller than those on my Quickattach grapple claw and have a finer pitch thread. Are these metric?

Kubota L5240, with cab and HLA plow. 1500' steep driveway in snow country. Works well, but in late winter banks get too high and we end up with a bobsled course. Options we're thinking of are: 1. Inverted blower; keep plow on front or not; don't know. 2. Front blower, but not sure they need...

Kubota 5240; read the manual on the 3pt hitch weight lifting limitations. But if you place a load on the hitch after it's raised, can it hold more than it can lift? Is there a ball check or other device in the hydraulic system that would allow it to hold the load?

Not thinking, I bought my fuel last July and this past December's continuous nights at 20 below gelled the fuel. I recovered soon enough by adding a couple gallons of kerosene to the 14 gallon tank, and a salamander pointed at the tractor for an hour or so; (also dropped the filter and added...

A search brought up nada. Have a 72" plow on the FEL. 1500' steep drive; banks getting too high; drive getting too narrow. Want to build some kind of add on blade that I can hook on/chain onto the plow, sticking out to the side 4-5 feet or so to clip off the banks pushing them further into the...

I recently had to remove and replace the fuel filter, and filled the bowl up again with fuel and screwed it back on. I opened the "bleeder" or priming control and cranked the engine. It took forever to start again. I tried multiple times (like at least a dozen times, for 10-15 seconds each...

As have many others, I had a fuel gelling issue this weekend. In trying to get it going again, I elected to jump the battery with my venerable Saab. Trying to reach down behind the grill to get to the battery terminals was an absolute bear though. I must be missing something. Do you need to take...

My Kubota manual says change oil every 200 hours. From my understanding of synthetic oils in the automotive world, you can go longer than with conventional oils. I'm using Rotella T6, changed at 600 hours; Now coming up on 800. Machine is a 5240. Thoughts?

My JL290 is a bear to pull the cable out. It vibrates when you pull and it just seems like there's too much friction. I've read the Clutch Adjustment section of the manual, and it's confusing. It says: "Pull the control rope. The lever should move up 1.5" before the clutch engages. If the clutch...

I know mice like to find nice warm places to nest when fall nears, so usually I'm pretty on the ball to check the engine compartment, in front of the radiator; on top of the fuel tank etc. I'd done it not more than 3 weeks ago. Was mowing my trails and out the corner of my eye I see something on...

I have an HLA2000 snow plow. It turns side to side too fast, so I installed to flow controls on the input side of the crossover relief valve. It did the trick last winter, but it seemed that many times, if there was no load on the plow (like level), that it would continue full stroke to one side...

It'd be great to have one that can tilt back to scoop up the material. Any recommendations?

After an hour of mowing, I park the tractor and notice what looks like hydraulic fluid leaking out of the little drain directly in the middle of the tractor...almost beneath the "windshield" of the tractor. When the engine cools, it stops, after leaking a few ounces or so. A friend thought it...

I'm restoring an old Bush Hog a neighbor farmer gave me. The 3 Pt hitch seems very high. Even with the lift arms all the way up, it barely lifts the tail wheel off the ground. My lift arms are in the lower hole, so I know I can use the upper hole, which might give me a few more inches of lift...

I have a lot of 12 year old slash and sawmill refuse, I'd like to make go away. It's too soggy to burn; I have no place to bury it; I've looked at those grinder things but they seem to be $20k+, they're hydraulic;no place to rent one even if I had front hydraulics. I had a guy with one price a...

I've learned (with my current Kubota L5240), that at times one rear wheel starts slipping (usually because of an asymmetric load on the FEL), I can press down on the rear differential lock with the left heel. But it's quite stiff, I don't weigh that much (well, more than I'd like), such that...

I've been having a heck of a time managing the hoses on my grapple claw. I've tried straps, bungees, you name it. They keep getting caught either on the top of the grapple tines or on the quick attach levers. Any hints on how to do this?

I know there are a huge number of variables involved with answering the question, but is it generally true that a tractor like mine (Kubota L5240), with only a FEL and nothing on the 3Pt Hitch, with loaded tires and wheel weights, (both of which tend to move the C of G rearward, would be more...

I have a relatively flat field, about an acre in size, that I currently mow. It's very uneven, with "pot holes" from stones I've dug out and hills and valleys...total variation in "elevation" from highs to lows is about a foot or so. Mowing it is like riding in an old buckboard with busted...

I have a Kubota 5240 with a Land Pride Rake. I'm trying to rake some of the hardback that got plowed this winter into the ditches on either side of my 1/4 mile drive. Relative Newbie. I've got two problems: 1. I've angled the rake fairly steeply, but when I lower the 3Pt, the slop in the...

I was reading a thread on the woes folks were having around corrosion caused by calcium in their tires, and want to know what I have in mine (I bought the machine used and the seller did not know). I took a photo of the stuff: totally clear and tinted slightly yellowish. For comparison, I...

We got 3" of icy slop Friday; My wife had guests from down country ("all season tires") come to visit, via our 1/4 mile steep drive. Ground was too soft to plow without making a mess; I had put the Land-Pride rake on some weeks ago when we had washouts from rain. I angled it and hit the...

I own a Quick Attach 72" Quick-Claw grapple Rake, on my L5240. It works well, but it weighs 800 lbs. I think it's just too heavy for what I use it for (moving saplings, brush, and small rocks. It's made entirely of 1/2" "T-1" steel, whatever that is. The thing is built like a tank. I'm thinking...

In this ancient, but fascinating thread: http://www.tractorbynet.com/forums/hydraulics/204621-diy-remote-hydraulics-2.html?highlight=30541 BirdBob built a block to replace what looks like a cap with a passthrough from one port to another. This is where Kubota's add on remote valves go. I...