I'm shopping hydraulic top-links for my Ford 1910. Seems some measurements are what I need - no problem. However, I'm now noticing a large "Made in Korea" stamping on the manual top link I...

My 1910 problems began with hard starting and a surging idle. It would have a rough idle followed by a high rev and back to a rough idle or just die. I had just began building my my shop and the...

Hi everyone — I searched for “k-seal” and “blue devil” and “head gasket seal” and didn’t get results so asking here: My 1910 has been running hot (the line just below max after 10-15 minutes) and...

Would anyone know the part number for the 4wd sliding gear in top of transmission 1984 ford 1910 tractor? It wouldn’t let me post a picture, I ordered a manual but it’s a month away

trying to find a used steering box any suggestions?

I’ve been trying to install a new westendorf loader on my ford 1910 however I can only get the psi above 200 on the diverter block when I put the 3 point hitch lever all the way to the top in the...

Hi all, My starter solenoid is acting goofy. When I engage the starter with the ignition switch the solenoid activates the starter just fine for about one revolution of the engine and then the...

Greetings, Replaced the timing gear cover gasket and started looking for the torque specs for the bolts that hold it on. Been through all of my manuals (including the repair manual) and the...

New to owning a tractor - so pardon the dumb questions. I have owners and service manuals but they are pretty poor and hard to follow for this tractor. I can't seem to locate where the front and...

First time posting. First day with the new (to me) tractor. Plowed a small garden plot for about 45 mins and then put it in the garage. Later noticed a puddle of fluid on the floor. Not a lot...

Good evening, I’ve taken on a project in restoring an auction buy non-runner Ford 1910. Apart from a cracked crank, which I’ve sorted with a second hand one, I’ve also discovered the front near...

Greetings, Been fixing up the old tractor fuel system. Right now, I'm trying to locate an equivalent fuel injector (or rebuild kit) for my 1984 Ford (Shibaura) 1910 tractor. The part numbers are...

My tractor sits a lot but is in great shape. It's a 1984 Shibaura (Ford) model 1910 3 cyl diesel. It starts but is reluctant to do so. Takes about 20-30 seconds of cranking (after 10 seconds of...

My tractor is stuck in reverse. 1910 4WD with shuttle shift synchromesh trans. I have removed the top plate and do not see anything broken. The shifter rail will not move out of the reverse...

Does anyone know where to find an exact replacement for wheels on a 2wd Ford 1910 I need the front and rear wheels for a restoration

Anyone know where to find a roof to fit a ford 1910

Hoping someone can help with my 4wd issue on my compact tractor. I did hear a loud pop when the 4wd quit working. I had the tractor off the ground today and if I turn one front wheel the...

Interested to hear other owners opinions and experiences

If I were to use biodiesel in my tractor what are the pros/cons

I’m wanting to know which transmission my Ford 1910 has there’s two types a synchromesh transmission and a non synchronized how do I need to check

My Ford 1910 is very light in the front with the 5 foot bush hog on it I ordered 5 50 pound weights that are the same as the originals will that be enough to make a difference

Does anyone know where to find a white roof for a Ford 1910

I’ve gotten a Ford 1910 recently and I would like to know what all I should check and replace to restore it back to it’s original power and condition it only has 820 original hours on it.the only...

Where can I buy a new air intake hose, part number SBA314540451, for our Ford tractor model 1910? It has a Shibaura engine.

I had my little 1910 sat in a little wood I own. I. Looking for a mower to fit it to cut a few acres of grass. I also pull the odd tree out for cutting. Recently some arsehole took it apron...

Team, I'm looking to replace the lightbulbs in a Ford model 1910 tractor. Current bulbs are incandescent 12V35/35WS and I'd like to upgrade to LED style. Any conversions bulbs known, or a...

Hello, I recently acquired a property and the previous owner left a 1986 Ford 1910. The tractor is in fantastic condition but unfortunately, it is missing the engine oil dipstick. I have...

Hi All, I have a '84 Ford 1910 that had the OEM mechanical voltage regulator that was putting out just a little over 17 volts to the battery. I have no idea how long it had been doing that but...

I have been working on an '84 Ford 1910 for a friend, and one of the big projects has been to mount and plumb a Woods 1009 loader on the machine. I got all of that done, and thanks to chander for...

I'm considering purchasing a smaller tractor for running a finishing mower and found a '90 Ford 1910 with turf tires that I'm planning to look at (have not done so yet!) The clock has 789.5 hours...

I have a great little 1910 that lacked a loader when I bought it. I found a loader from a machine (also a 1910) at Weaver's and am having trouble figuring out the plumbing. The 1-arm loader valve...

Ford 1910 Compact Tractor Seatbelt Attachment Points? Greetings, Have a great little 1910 (1984 model) compact tractor that I managed to find an ROPS for, so need to also reinstate the (missing)...

New-to-me Ford 1910 (1984). Looking for photos of how the ROPS posts attach to the axle. Or anywhere. I bought the tractor without an ROPS and found one for it at a salvage yard. Can't find any...

Have a line on a 771 and need a loader for my 1910 tractor. Anyone know if these will bolt up without modifications? I know the 771 was specified for the 1900 (and the 770A/B for the 1910), which...

Good morning, A new 1910 owner with operator and service manuals in-hand. Unanswered question: What material is the fuel level tube (that serves as a fuel gauge in pre-July 1985 1910s) made of...

I've never owned a tractor before buying this Ford 1910 with Synchrcmesh transmision shuttle shift. I ordered a 6' county line tiller for and trying to learn how to use it properly. Downloaded the...

Need a little insight on this one. I have an opportunity to get a 1510 for parts, and I own a 1910 that the front axles are missing, as well as the transfer case. My question is, are the 1510...

Hello, I have dismantled the fuel injectors from my 1910, the first one was just like the books say but one of the nozzles had the center pin fall out. Every where I see exploded vies of this...

Hello, Can anyone help me with removing the water pump on my ford 1910? I just installed new sleeves, pistons, rings, valve job, head is back on but I want to replace the water pump gasket. All...

I have been having an issue with my three point creeping down when my loader is attached. I think it is in the divert valve. It doesn't do it with the loader detached. I took the valve apart and...

Morning! I'm brand new to the tractor world. I have driven a few back when I was young but I didn't really pay attention to what I was driving, just the job at hand. So, the ground this tractor...

I have a Ford 1910 that yesterday blew a hole in the side of the block. I suspect that it dropped a valve. Not interested in tearing it apart. Has a 770B loader 4x4 everything works great, turf...

Found a Ford 770b loader to put on my 1910,,the hydraulic connections on the block that I took the loader off of are parallel along the top of the block, the block on my tractor, one is along the...

I am replacing the water pump on my newly acquired Ford 1910 tractor. I am considering removal (not replacement) of the thermostat while working on this job. I live in way south Arkansas and plan...

I just bought a 1985 Ford 1910 tractor/loader that didn't not run, looks great, nice and tight but I was told it just had an injector pump problem. I was lied to. I need to find a rebuilt head...

I have a Ford 1910 with 13.6 x 24 Ag tires. I'd like to get something a little more friendly to the lawn, but not so bad it's worthless in the snow. Something in between an aggressive ag vs...

Replaced cylinder head on Shibaura 3-cyl diesel on 1983 Ford 1910 tractor. Preparing to adjust valve timing and need some help deciphering the 2 marks on the flywheel. See attached photo...

I have a 1910 that was working fine until I found it with the key on. I have a service manual and ran thru all the tests. I tried a new alternator - nothing. I have tried 3 new regulators and with...

I have a 1910 that I've discovered has a leak where the injectors are screwed into the head. Crazy how it was discovered. I was refueling and spilled a bit of diesel fuel over the engine. What...

I have a Ford 1910 with the Shibaura 3cyl diesel. It has been trough a lot and the diesel has got to the point of being beyond repair. By me anyway. I'm looking for advice on possibly replacing...

I have a 4wd 1910 with shuttle shift that needs a transmission overhaul. New Holland no longer stocks parts. Did any other tractors have the same transmission? Are there other transmissions...

Hi, I was wondering if anyone would have standard crankshaft sizes for a Ford 1910? Thanks:)

Hey guys, I have a Ford 1910 with 770 loader. The tractor has a hydraulic manifold block in front of the brake pedal that can switch the hydraulics from the loader to the 3pt. One of the quick...

New to this site. If I seem lost I may be. Please be patient. Parked my tractor for about a month maybe longer but not much longer. hyd's worked fine when parked. after work was done on house I...

Hi folks - just joined the forum. As the title says, can anyone tell me what RPM the engine will be spinning if I'm turning the PTO at 540 RPM? I'm looking at getting a PTO driven generator and...

So, I'm working on my tractor because there a pretty good knock when I first start up the tractor. Once it's warmed up for a minute or so, it goes away. My natural assumption was that the valves...

Hi new here just recently bought a 1986 1910 4x4 I have a guy putting a new clutch in it. And who ever worked on it before screwed up the first part of the threads on the crank where the flywheel...

I have a 88' Ford 1910 tractor. The other day I noticed that the battery light came on and was staying on. ( I replaced the battery with new interstate battery approx 6 months ago- when it failed...

Im looking for parts for a ford 1910 cant find this part on any diagram. Its some sort of port/ nozzle for the fuel. Its goes in the bottom of the cylinder head opposite of the fuel injector...

Hi Folks, Just wondering if anyone knows if the timing cover needs to be removed to replace the seal for the crank shaft?

Hi all Just picked up my first tractor ever, a 1984 Ford 1910 with 1600hours. Few questions: It has some trouble starting. I let the glow plugs go for about 15sec and then crank it (been warm...

Can you adjust the rear diff lock? I have a Ford 1910 that is behaving this way: If I press the diff lock pedal down, nothing happens. If I use my heel to lift it up, I can get it to lock...

I'm new to this forum and found a few posts that touch on the issues with my Ford 1910 but not everything at once. At low RPM (or with the engine off), the three-point hitch will not support a...

First time this happened it sent hydraulics oil into the motor. Took pump off and really at that time checked the shaft for wear and just replaced the seal.. The next day after replacing seal it...

I have a 1910 ford tractor. Could anyone help me with the valve clearances and the procedure to do it? Thanks, Jeff

help! have a 1985 ford 1910 tractor, and its barely able to move or brush hog when it gets warm! would a clogged fuel filter or other filter cause this? i have yet to change out any fluids or...

Hi All, I am a new owner to a '84 Ford 1910. I have been on a 30 HP utility tractor plenty in the past 30 years pulling a bush hog mowing pasture but now I am entering a new horizon in that I...

Hello, I just recently inherited my tractor with the purchase of my new home. I have noticed that I have been getting stuck a lot this spring with the soft ground and observed that only one rear...

Fuel gage doesn't work on my 1910. What do I need to do to check it?

Anybody ever replace the brake shoes on their 1910? How bad of a job is it? Do you just pull the fenders, then take the bolts out of the housings, and that exposes the drums?

What should be the voltage at the glow plug when the key is turned to the preheat position? Right now I am getting about 9.5 volts. I looked at a wiring diagram and believe there is a resistor...

Hi All, I checked the search and didn't see my issue. My ford 1910 front end was locked up in and out of 4wd. If I lift the front off the ground the front tires spin free in opposite directions. I...

Ok, well I'm continue to upgrade my Ford 1910 machine. So far, here's what I've done: * Changed all fluids and filters. * re-cored the radiator * new thermostat and gasket * rewired the lights *...

I have a Ford 1910 with 770 loader that I am replacing the ridgid hydraulic lines on the loader. Anyone have any tips/suggestions on start-up i.e. priming, air in lines etc.? TYIA

hi guys, I have a ford 1910 that I have always had problems with my hydraulics freezing up when it gets really cold. Usually after let her run for a bit they get warmed up and start to flow...

I have a ford 1910 that has a rotted out rim in the rear. Replaced the other one last year with one from the NH dealer, which cost about $500 for the part. Does anyone know if there is any...

I have a ford model 1910 and the hydraulics have slowly deteriorated to the point where the bucket no longer moves and neither does the 3 point hitch lift arms. When I changed the oil filter...

My tractor started missing like it might be low on fuel so I stopped and filled it up. When I tried to restart it I got a few puffs of smoke out the stack (normal) then nothing. I changed the...

bought a used 86 Ford 1910 tractor. having an issue with the shifter stay in gear. both the gear and range just wiggle in the wind. any thought s what might be going on?

Posting hyd info from recent fix. I am acft mechanic 34 yrs. recently my 1910 3 pt lift ceased to wk. I have a service manual and set out to fix it. 1st I tried the hyd press test as called out in...

Posting hyd info from recent fix. I am acft mechanic 34 yrs. recently my 1910 3 pt lift ceased to wk. I have a service manual and set out to fix it. 1st I tried the hyd press test as called out in...

I am relatively new to tbn and recently purchased a 1985 Ford 1910 with a loader a 5 foot bushhog...which would be considered my "first" tractor. I will start by giving you a little info on myself...

Hello, ijust bought a ford 1910 with turf tires and am thinking of changing to ag tires. Does any one know of any other make wheels or center disks that will work on the rear of this tractor. They...

Hello All, I just recently purchased a Ford 1910 with a Du-Al loader for $3500.00. I plan on using it to landscaping work around my place. The amount of hours on it are unknown. But, everything...

I've gone thru all the wiring on my 1910 and replaced the voltage regulator but the tractor will still not charge. The charge light remains on. I've checked all my connections but still can't...

almost killed my helper how do i get at shoes i started on the right side removed finders then the small bolts when i got to the 15 16 bolt my voice in my head said you need more info , so...

I have a Ford 1910 manufactured in 1986 and the front differential oil has started leaking out steadily. It emerges at the 2 front wheel drive unit at the point where the top half of the unit...

Newbie here with a counterweight question, and not able to find an answer using the manuals. I'm going to make a concrete counterweight for loader work, but can't decide what weight I should aim...

I bought an old 1986 Ford 1910 last fall. Hydraulics were working. It sat outside all winter-covered when the wind didn't blow it off. It got water in the reservoir. I drained it a little and put...

Has anyone rebuilt a Ford 1910 3 Cylinder Diesel? Was wondering how hard it is or costly to replace sleeves and pistons. Is it worth sending to a shop for repairs? Any info would be appreciated...

Re: HELP PLEASE- Ford 1910 - ANTIFREEZE IN THE OIL- HEAD GASKET I had a chance to run the tractor. The top radiator hose gets warm and so does the small bypass, but the lower radiator hose does...

Hello Everyone, I have run into a little problem. I have split my tractor for an engine rebuild and now have to rejoin my tractor and I can't find a clutch alignment tool. The tool steps are...

I have a mid 80s 1910 4wd with 1180 hours. It runs like a champ and is impressive for the size and weight. After a couple of months of moving soil, I hooked up my finish mower and discovered...

I have a Ford 1910 tractor which the PTO disengages when trying to shred. I was curious why this may be occuring? Should I add hydraulic fluid? the PTO operated fine but after shredding for a...

Any suggestions on how to disengage the diff lock? Tried pulling it up by hand, but no luck.

Hello all, What I have is a 1986 Ford 1910 2wd with a frontend loader added on(Ford). My problem is since I've owned the tractor the frontend loader will operate extremely slowly with an...

Hi everyone, could use some advice on a 4WD 1910 with 770-A FEL. It has 1482 hours, and a fair amount of surface rust. I don't care about appearances all that much, as long as it works, I can...

so it all started with a charge wire to the starter terminal getting hot. I replaced the regulator and also the ignition switch, since it had a spot were it would not connect to the glow indicator...

Looking to purchase front axle bearings, seals and gaskets

Has 4WD, 665 hours and 7108 loader. In good shape. Shedded. Seat, paint & metal look good. Checked Tractor House looks like ~$7,500, but there's not many for sale to compare.

Hello I'm new to this site. I was wondering if anyone could help me with some problems I'm having with my series 1910 Ford Tractor. I need to know how to adjust the lifting pressure?? Any takers...

I am looking to purchase a ford 4x4 diesel 1910 tractor. It has 2900 hrs. The pto brake doesn't work. The owner says the pto doesn't stop when you press in the clutch. How big of a deal is...

I'm very seriously looking for a backhoe attachment for my '85 Ford 1910. I see that Ford originally wanted to pair either the 757b or 758b with my unit. I see that the 758b has a deeper digging...

I have a well used 1910 with a back hoe powered by a pto driven pump. As far as I can tell the back hoe has not been off it for a very long time. Provided the rpm is low the pto can be engaged...

I currently own a Model # 1910 Ford Tractor and I found a model 702A snow plow will it fit? Any help would be appreciated. Thank you.

Does anyone know if a Bulldog 285 loader will fit on my Ford 1910, any help appreciated.

Hi All, New to Forum.........Been having hydraulic lift problems on '83 Ford 1910 4x4 Tractor and wondering if anyone knew of sure way to test Hydraulic pump and pressures. Don't know what else...

I have a ford 1910 tractor that when i try to engage the pto to operate the finish mower, it grinds while engaging, even at the lowest idle possible w/o stalling the tractor.Whats the problem and...

I'm buying a ford 1910 with frontend loader with 600 hrs a bit weathered but in pretty good condition.I have a ford 8n but would like a tractor with a frontend loader.

Hi Folks, New here and need some insight into your experience. I have a Ford 1910 4x4 with Woods FEL. Recently while plowing out potatoes, I was checking everything out, fluids, greasing, etc when...

I've used my tractor for the first timetoday..I mean more than back and forth pratices while waiting for the snow. Wich snow arrived today so I went out to get it working a bit.I needed to go...

I wondering how much to ask for my mid 80s Ford 1910 4x4, about 1000 hrs , comes with 702B dozer blade and 5 ft Woods bush hog , The tractor and blade are in good shape , bush bush hog is fair...

Does anyone have a pic of the shifter that is on the column. I believe there is 4 gears and the reverse on the column. Yesterday a piece came off or something shifted which cause it to stick. I...

Trying to score a 1910 from a guy here locally. Going to look at it saturday. They disassembled the front of the motor (3cyl diesel) to get the injector pump off and havent put it back together...

Hi, Is it normal for my temp gauge on my 1910 to show high temp when switch is off? When I turn that switch (ignition) fuel gauge goes up but heath down to cold as it is when just...

Hello All, I have a Ford 1910 Tractor with some PTO clutch issues. I purchased this tractor last year for $8900 up in Washington. When I push the clutch down all the way the PTO does not...

Hi,here is a picture of the 1910 I had recently.1200 hours,1986.If I can I will squeeze-in a second photo showing a cut wire sticking out from the transmission cover...anybody knows what is it...

Hi, After over a month scrutinizing tractor ads,when I saw this 1986 1910 with an Allied 380 loader and a nice vintage 72 inches McKee snowblower,1200 hours,I jumped right in at distance through...

My Ford 1910 has always needed 20 seconds of pre-heat to start and this has always unsured a prompt start. Until this week! I noticed the engine turning over quite a few times before it would...

does anyone know how I plumb a backhoe into my ford 1910 has loader with quick connect but not for hoe if any one has a 1910 with a hoe pics would save my life I am not totally ignorant on hydro...

Hi all, New tractor owner here....yes I'm a girl, but I hope ya'll won't hold it against me haha... Anyway, my question is this, we need haying equipment and I don't have a clue what my tractor...

Need to remove the drive shaft on a 4wd 1910, what is the trick. I have removed the 4 bolts attaching the collar to the front differential and the single bolt at the rear. I have clue I might have...

Trying to help my Dad find a glow plug for his pre 1984 Ford model 1910 tractor. I ordered him one online but it was too long. He has pulled one out and says its a NGK 544. I've sent an inquiry...

i have just gotten a 1910 and we are getting around to changing fluids and filters before we put it to work, i need to know how to change the oil for the injector pump a diagram would really help...

I am starting to look into a replacement for my 1910 Ford and going for a little more Hp and getting away from the two stage clutch but keep the gear transmission. I have it narrowed down to these...

I recently purchased this tractor used, and it didn't come with any of the operator manuals and most of the operation decals are gone/painted over. It's a 1986 model year Ford 1910 tractor with a...

I have been looking at a Ford 1910 with a Dual 110 loader.It has 1429 hrs. and is a 1986.The price is around $8000.My question is,is this a good tractor,at a good price?Thoughts anyone? tnx,stan

Hoping someone can help, I need a picture of the airhose, on a Ford 1910 3 cylinder. The hose goes from the intake to the aircleaner. My tractor is a Bradco conversion backhoe/loader. It uses a...

Hello, just found this site! I have a ford 1910 4wd with a 770 ldr and need to plumb in remote hyds to operate a jd 1207 mower conditioner that I want to purchase. What is the best way to operate...

nhown-ML-725006-ML- brand specific

power steering leaking around the base of the steering gear assembly. Just bought this tractor and I am not sure what the solution to this problem is, any suggestions welcome. thanks gerry

I'm looking at a Ford 1910 tractor. It has 978 hs. on it. It is slightly weathered, but that is mostly cosmetic. A can of spray paint and some sand paper and she'd look great. I think she is a...

The three point lift on my 1910 will not lift a 6ft bushhog after the hydraulic fluid heats up. Also when an implement hooked to the three point is lifted to a neutral position not fully up the...

I am a first time tractor buyer looking for a used 4 wheel drive tractor with loader to maintain 35 acres. I've found a Ford 1920 without a FEL for $10000, and a 1910 with FEL for $7500. Both...

I got it all apart, the ring gear is shot and so is the drive gear. How on the green earth do you get that thing out? Any help would be great.

Pulling a stump in reverse something started skipping in the front end. Well 4 wd you could not use, the left front wheel locks up. So I used 2wd, now the 2wd is locking up. should I drop the...

I have a Ford 1910 with the syncromesh transmission. I have recently developed a problem where the transmission would jam when shifting from reverse to the forward gears. I would have to jiggle...

I have a well seasoned 1910 ford, last week i went to move some snowbank(weather has been 10-20 degrees), made one pass and the hydraulics were dead, no loader, no hitch, no power steering. feared...

Ok, Does anyone have an idea where the vent for the front differntial on a 1910 Ford is located? I've looked all over. I can tell it's plugged due to the fact that after driving around when you...