Hi folks, I have a 14 year old 800hr BX1860 on which I've just discovered the propeller shaft front joint cover (aka dust boot) (item 20 below) has worn through and fallen off. Interestingly...

Someone near me is selling a tiller but they said it has some special PTO for small JD tractors. Would that work on a Kubota bx1860?

I am new to this forum and fairly new owner, and also not a lot of experience with repairs. I have a BX1860 that has a clunking started in the front axle area. I discovered fluid leaking from...

I have a Kubota BX1860 that will not start nor are there any signs of combustion. I have performed the following to the fuel system: Removed fuel tank and cleaned out the garbage left by the...

Hi, I have a large coolant leak in my BX1860 - in just a few minutes of running, all the coolant went into the crankcase. It didn't really mix with oil, the oil was floating on top. So when I...

I was just gifted a bx1860 w 1260 hrs and is a 2010 model I believe since bought in 2011. Looks impeccable and was diligently maintained. Has only a mmm. Want the loader capability. Before I buy...

So my bx1860 was doing the typical clicking sound it does before you turn it on but it wouldn't turn on. Battery is fine. PTO and pedals seemed fine. I looked at fuses and they seemed fine...

I am looking at a used 2015 Kubota 1860 with over 700 hours and I was hoping that anyone with that year model could comment on it as I need a new mule since the lawn mower is on its death bed...

I got a bx1860 with hst. Was running good when All of the sudden my foot lever went limp, no forward or reverse. It will not rev up or whine when I push the lever forward or reverse. It is my...

I got a bx1860 with hst. Was running good when All of the sudden my foot lever went limp, no forward or reverse. It will not rev up or whine when I push the lever forward or reverse. It is my...

I have a BX1860 Kubota that drips some oil from transmission after using front bucket or raising rear blade a lot, seems to be coming from top left looking in from rear. This started after heavy...

I've been scouring the internet for weeks trying to find a reasonable way to add suspension to my OEM seat. Haven't found anything that says it will fit, and I even bought a universal type in the...

Incase anyone was interested, hard to find much about it. I needed more grip.

I changed both my fuel filters at my 50hr service. Now at 133hrs, the one under the floorboard looks funky. So I copied 4shorts and put a Kubota Grand L filter on in its place. I liked the...

I would like to do some grading work on a sloped area of my lot that is mostly clay and won't grow grass. I want to work in some top soil and manure and a box blade seems like the best implement...

I am think about build a pto pump setup for my bx1860. Has anybody build a pto pump for compact?

Tractor has 200 hours, and is in good condition. This is for a buddy of mine who after using my bx25 is looking for a used one. Asking price is 9900, sound fair? Also comes with 3pt setup.

Hey all, Using my tractor all day was fine, started every time . Was working out of the bucket drilling my flagstone house for new shutters. Finally got done and ready to put tractor up for the...

Hi there! I'm new here, so bear with me. I have a Kubota BX1860 diesel tractor about 3-years old. During the Spring and Summer it gets used weekly for mowing with a 54" belly mower. This year...

Has anybody install a aftermarket market loader on the BX? What is a reasonable price to pay?

Hello all, I've just picked up a second hand BX1860 (2010 model I believe) with just a tick under 150hrs on the clock. As a precautionary measure more than anything I thought I'd change/renew...

125 hours hes asking 9500 . What do you guys think?

Found a used BX1860 from a private party. Has all the toys, FEL, 54" mid mount mower deck and a nice box scraper. He's asking $9,800. Says he paid $13,100 for everything, which sound about...

Hello all, My tractor will turn over and fire, but it won't run. It acts as if there is a fuel starvation issue. When I initially turn the ignition to the "on" position, the familiar clicking...

I've had my BX1860 for almost 6 months. The only thing I've had on the three point hitch is a towing rig (triangle with a 2" ball and a 1 7/8" ball and a place to connect a chain as needed - this...

I'm into my third year of ownership with my BX1860, and I've never wished for more power...except I really wanted a wood chipper. I have a large stand of pine trees on my property and boy do they...

I checked on a Mulch kit for this BX1860 I will be getting. I spend a lot of time in the fall with leaves. A dealer along time ago talked me into a mulcher for my GR because I told him I spend...

I've had a bx1860 for 2 or 3 years but never used the lift and just tried it for the first time and it only goes up, I can't get the lift arms to go down. Am I doing something wrong?

The BX1860's are about gone, but the local dealer could get one from another dealer. The BX1870s are available. I'm weighing which model to get: - I like the new dash displays on the 1870. - The...

hi, my name is Wayne and i'm new to the group, my first real tractor. i just purchased a 2011 Kubota BX1860 tractor with a FEL and snowblower and i'm looking for a mower deck and later on a...

Hi all! Today I was helping a neighbor move some dirt. It was quite wet and heavy and about 12 yards. Well, when we were almost done I noticed drops on the ground. I thought maybe a sprinkle...

I have been reading reviews and posts on this site for about a year. I have learned a lot from reading posts. I recently decided to look into a sub compact tractor. I already own a Kubota L3540...

Looking for ideas here... I've have a BX1860 for 3 years now and my only complaint is the volumetric capacity of the FEL. The sizing of the FEL is such that I can pick up and safely move a full...

Can I upgrade to the larger BX 2360 tire/ wheel combo? I believe it's the same bolt pattern. Thanks, Bill

hi all figured som people here will hopefully give some input . waiting on delivery of my brand new bx 1860 got it with 54inch deck, and 5 foot hydraulic snowplow . dealer threw in weight box and...

hi all figured som people here will hopefully give some input . waiting on delivery of my brand new bx 1860 got it with 54inch deck, and 5 foot hydraulic snowplow . dealer threw in weight box and...

All I see is that the 1860 has metal hood and fenders apposed to the 1850 plastic.

I have a BX1850 that needs a new hood. I would like to install the new metal hood from the BX1860. Has anyone done this before ? Also were is the best location to weld hooks on the bucket of the...

Hi What is a fair price? I am looking at a new BX1860 with softcab and front mount blower... possible mm deck at well. Anyone priceout/purchase anything simiar? Thanks

I just purchased a new BX1860 with turf tires because I didn't want the ag tires to shred my lawn but fear that the turf tires won't have enough traction when I am working on my lot to get it...

I bought my Kubota BX1860 last November and readied it for the winter snow. Equiped it with chains and hydraulic front blade and was good to go, however, never got any snow............anyway...

I have a bx1860 with a RCK54P-23BX MMM. I have mulching blades on it but I am starting to think I need something else for mulching. Should I at a minimum have something covering the side so grass...

Does anyone have the blade part number for a BX 1860 54" MMM deck we purchased last year? Are there any options? Thanks all.

Just after lunch today I told my wife we should get some skid plates for our tractor... then a couple of hours later ran over a stick and broke the blades off the HST fan :ashamed: Searching here...

Any 1860 owners here? If so, I've got a question about the hydraulics. As far as I see, there's only one lever which controls the raising/lowering of the 3PH arms and the mid-mounted mower...

I used my new BX1860 today for the first time. How pleased I was! It's outfitted with a hydraulic blade and rear wheel chains. I never slipped once and was able to push 6 inches of snow UP the...

Hi all, I'm the Mainecoondog and in August of 2011 I became the owner of a brand new BX 1860 with bucket, front snow thrower, back blade and ballast box. This site helped me to deside on this...

Looking at buying a 2009 BX1860,196 HRS.,FEL,54" MMM, and R4 tires,very clean unit, 1 owner .Anyone have a ballpark figure what a guy should pay or the value of this unit

I recently purchased a BX1860. I love the tractor and now would like to get some attachments at the cheapest price possible. I live in South Point, OH does anyone have any suggestions? I want to...

I am interested in a quick attatch for the 3 pt hitch on my BX1860. My box blade and disc are setup with hitch pins facing in! While my short single point plow from Tractor supply is setup only...

Hey folks, Last year I asked for and received great advice concerning my decision/convincing of wife to by a BX1860. I did buy this sucker in March, just in time to do one snow blower test run...

Hey folks, I'm new to the forums...Looking to purchase my first tractor to help me manage 13 acres in NC. I've done a lot of reading on the forums (thanks!) and have concluded that a BX-series...

My wife was mowing the lawn the other night with her new BX1860 and all of a sudden it died. No sputter, just shut down. Restarted OK. Then when she parked it it did not want to shut off. I...

Good morning...purchased a new BX1860 earlier this year with a 48" MMM and FEL. It's all good (~40 hours on the clock) except the temp gauge will run to the red while using the mower, especially...

Hi guys, Marvin from Barlows delivered my new BX1860 today. Heck of a nice guy.....Showed me all about the tractor. First class all the way.... Great little tractor, I know, I know pics are...

Hi, I have a 2010 BX1860 with the 54" MMM (the non-fine cut type). The BX has got just shy of 100hrs on it, and the MMM has been hanging off the tractor for I'd say half of that time. No...

I've been looking at both the 1860 and 2360. Are you 1860 owners happy with it's capability. Is there anytime you said I wish I had or needed more power. I've got 1.25 acres to mow and would use...

Hi All, Just ordered my new BX1860 with the FEL and 54" standard deck today. (Cant wait till saturday, feel like a kid again) anyway, I forgot to ask the dealer today about mulching kits for the...

I was thing of buying a used Kubota bx1860 for mowing, snow plowing and moving mulch, wood, and top soil. I have around 2 acres to mow. Any advice on pricing for a used machine a couple years...

Hello all, I think I have decide that I am going with a small Kubota. I've convinced myself, for now, that I don't really have any long term use for a backhoe, so I a have ruled out the BX25. I...

I've decided I want a little Kubota, and I've visited several dealers around here and found one I can work with. So it's time to make some final decisions on how to have this tractor set up. I...

Just installed a Mulch Kit on my 48" Fine Cut Deck. Very easy install, Won't be cutting grass for a Week.Rain for the next 5-6 Days.

I want to change the blades on my bx1860. It has the 54inch MMM. I don't know the exact model of the mower. I know I do not have a mulching kit but I was wondering if it was possible for me to get...

Worksaver makes a hydraulic posthole auger with a minimum hyd flowrate of 5gpm. It is model 614H, and details are available here: http://www.worksaver.com/Manuals/924.pdf (see page 21) Note that...

Hello, First of all im new to this site and owning a Kubota or any other tractor for that matter. Anyways, I purchased last year a BX1860 with a 48" bush hog mower for mowing 20+ acres. I would...

Last Saturday I thought I'd scrape the last few inches of snow off the driveway in anticipation of a thaw heading our way. I was about 80% done when I smelled hydro fluid. I looked back at the...

Hi all, yesterday I ran out of fuel and refilled, then finished up clearing the snow and put the tractor away. Today it stopped running after about two minutes and won't start. I see that there...

It's done! Traded in my BX1860 for a BX25. Signed the papers on Tuesday and my new BX25 will be delivered sometime next week. Dealer said they might be able to get it to me by the end of the...

I am new to the modern day sub compact tractors, So please forgive this stupid question. i have seen a few posts about the problems of not using the proper oil in the hydraulic system. I...

I have BX1860 - I might be the most junior of you all and have very small tractor but enough for my urban use. I was wondering how much a small snow blower cost for this tractor which mounts at...

I asked this in another question because it came up, but I thought I'd make a new thread for it. When moving snow with my FEL on my BX1860 I have my box blade on the rear for counterweight. But...

I will have to do a little welding on my BX. Will I have to disconnect the ground Thanks Tony

Hi all, I am torn between the 18 and 23 pony options. I have taken some measurements and the 48" MMM is the right choice for my yard. Can a 48" MMM mount to a BX2360? I want the BX2360 because...

I recently sold my BX1860 and purchased a new B2320. Encouraged by some of the guys, I am going to "log", over some time, my sense of the differences, similarities and how these two machines...

Well, I did the 50 hour service. Oil, filter, HST filter and cleaned HST screen. I swear it too longer to remove the front grill and remove the MMM than it did to do the rest. lol.. The cork...

I have a small bx1860. I need to seed about 1 acre this year, and 2+ next year. I have already sprayed the weeds and they are pretty much dead. What should I do next? the soil seems pretty good...

So I'm getting ready for my 50 hour service already! And was reading again through the long post on doing this. I double checked my manual and it does not call for a fluid change, and it...

I had a busy day with the BX today. Up till now I've just left the MMM on but where I was working (digging and box blading) I didn't want roots/rocks etc banging up the MMM. So I decided to take...

Last year I purchased a DR Rotohog pull behind tiller as seen here: DR Rotohog Then I had a Cub mower that I pulled it with. It's a really great tiller. Now that I have a BX1860 I'm wishing (I...

I am facing some heavier work in my yard and need a bigger tractor. Currently I have a 6 year old John Deere Lawn Tractor but it will not be up to the task. All I can do with it is mow and pull a...

Quick question and first post (just found this site! Nice!) When using my 3PH to tow a tiller, aerator, etc I put the MMM in TOP mode. But when I lower the 3PH I see the MMM does drop a couple...

Hey TBN, I've gotten busy for the summer, but I wanted to check in and let you all see the new machine. Forgot how nice they look when new. Good delivery guy named Don, what a trooper...3...

Hi, Hopefully a simple question. What is the hole diameter of the blade used on the BX1860 54" MMM RCK54-23BX? Or asked another way... What is the correct Gator Mulcher blade for use on a...

I have searched both this site and the web but cannot find anything. Is there a foldable rops or roll bar for the bx1860 or 1850available anywhere? Has anyone put a hinge on theirs or found a...

I am interested in a 48" mid mount mower deck for BX. Must be 48", PM me. Thanks much.

I am looking for a tiller for my bx1860. I recently had 2 acres cleared of over grown brush. I want to till and rake the area and establish grass. What should i look for in a tiller. I am VERY...

I have my new bx1860 54"mmm,FEl,brush cutter and landscape Rake for a week now! LOVE IT!! I bought it from Barlow equipment. I can not say enough good things about Brady Barlow is a straight...

I just bought a BX1860 and I think I need a tooth bar. This would be for general landscaping around my home including leveling ground, spreading compost and top soil. My questions are: 1. Is a...

It's been about two months now since my new BX came home and every time I use it, I am more and more impressed. I mean, how did I survive without this useful toy all these years? First, let me...

I've lived in my house for 9 years. I've ownwd my BX for two months. When I bought, the property was littered with everything you could imagine. A late 60's Chevy Nova was on its roof in the...

Hi,I'm trying to decide between getting a bx1860 or bx2360, with FEL and 54MMM for the 1860 and 60MMM for the 2360.I have just under 2 acres, with probably 1.25-1.5ac to mow with a lot of...

Well, I got a set of Gator blades today and mounted on my 54" Fine Cut deck, the number is 96-748. I have the mulch kit installed as well and while at greased the deck and topped the gear oil...

When I move my lever to engage the pto for the belly mower there is a delay of from 7-10 seconds before it engages. Is this normal? I don't remember it taking that long last year. Fluid is at a...

I was curious to know if anyone sells for cab, A/c,heat, radio? And how much should that setup cost. Any idea pls? Ganesh

I know an they are 2 different tractors. I found a 2000 B2400 for $7500 with a FEL and 60" MMM. But it has 2700HRs. 6% for 5 years. OR a BX1860 for 11500-13000 depending on where i get it. 0% for...

How much should the cruise control option cost on the bx1860? Basically my wife bought me a bx1860 secretly for my birthday, its all great, but its missing cruise control (at least as far as I...

Barlow's delivered my new BX1860 today :D. I already have a Grand L so I was looking at getting just a used BX to mow with and pull a small trailer, aerator, etc. I figured I did not need the...

I have like 4 stumps to grind, is there like stump grinder on PTO shaft for Bx1860 size tractor, I can rent or buy if it is cheap? I need some ideas from the Gurus here Ganesh

So my wife bought me a bx1860 for my birthday (kubuta dealer messed up and it won't be here until Monday), anyways, and I will need a box blade for it. The kubuta dealer quoted me for $680 a...

I am considering a bx1860 very seriously however on most forums I hear the pto is a category 1 but my dealer says its 0. I am very confused. Which is it? Thanks, --Carlos

So I got two quotes now. Mahindra 1815hst for 11800 with 0% for 48 months (10700 with 0% for 36 months). Kubota bx1860 for $12150 with 0% for 60 months. Both have a front end loader and 54...

I bought a BX 1860 last week assuming that it would be delivered with the LA203 loader that I ordered. When the delivery arrived the tractor had the LA243 loader instead. I mentioned this to the...

Hi All I am a new member and was reading lots n lots of info. It was very interesting so thought of becoming a member and share my experiences or ask questions. I have a neighbor with BX1500...

Hopefully, an interesting story. Bought my BX (at a good price) 10 months ago. It was perfect in every way, but then, quite unexpectedly, I got a huge (for me) contract for organic foods...

OK, so I have always wanted a Kubota, who hasn't?:confused: Last week I stopped in a local dealer "just to look". Got a price and ok, they have 60 months 0% too. I like 0%! Still just...

I am replacing my Wheel Horse 520H (20hp Onan/ Hydro) and want something more powerful AND 4WD. Plowing snow is hard on it and I really want a FEL too. I have no need for a backhoe, but if i get...

What would be realistic good deals on a bx1860 and 2360 with a 54" mower deck, with loader valve but No FEL? The 54" deck would be preferable due to space constraints. I am in the mid-atlantic...

Hello everyone. I'm a first-time poster and have just begun to scan the forum off and on over the past week. I am a Kubota G2160 owner since 2001, and have been pretty happy with it. I use it...

Ok, So I have been seeking a tractor for general lawn care. I know either one will be overkill, however, I looked at "garden tractors" and for the money, they don't do much more than cut grass...

A good deal of my mowing involves tight spots. How maneuverable is the BX1860?

Is this an overkill for the my tractor? It is at the low end for my tractor power wise, but I am thinking to buy at that would be better in case I do upgrade or re-sale value? Thoughts?

In case anyone is searching I thought I would do a quick review of my Kubota bx1860 on my Minnesota vineyard. I have the front end loader and 54 inch deck. And, of course, the engine heater...

Got my tractor today, and so far I am really happy with it. I got it with loader, ballast box and 54" mower, on turf tires. After I get used to it I'll decide if I want to add on a rear blade...

Hello all, new owner and waiting for delivery of a BX1860 with FEL and RB. It also will have the 54" Fine Cut deck and Mulching kit. I am very excited and can't wait to get it but there is one...

Does anybody know if a snowblade from an L series tractor will fit a bx 1860. I cant seem to find any info on this anywhere.

On Saturday morning, I noticed a 2" puddle, well, spot really, of fluid under my BX parked in the shop. Cement floor makes seeing such things easier and with a new machine, one's eye is really...

Greetings. First post - excellent forums here; I have learned a ton already. I will soon be buying a new Kubota tractor, my first ever tractor, and am hoping to mine some expertise from those who...

I an a new owner with not much knowledge. Is kubota my only option for a FEL for my 1860? Not that there is a problem I just want to explore all possible options prior to purchase. Looks like...

This past weekend, I installed my 54" MMM for the first time this season (did first few mows with the wheel horse). I have issues with the deck clearing the frame when trying to roll it under the...

What's a good price for a BX1860 w/FEL, 54"FC, ballast box, and grass catcher?

I'm trying to decide between these tractors. I have a little under 2 acres about half of which I will mow and the other half is wooded with large trees (some of which I may try to establish and...

Hi all, New here. Friday I bought a new BX1860 with the blower and 48 inch mower. It cost a fair bit and seems well built. What I am wondering is how reliable and durable is this equiptment...

Looking at both. Want FEL, 54"fine cut mulching blade MMM, grill guard, ballast box. Turfs on 1860, R4's on 2360. Can you run the larger 2360 tires on the 1860? Do I need the extra 5HP? Is 18hp...

Looking at both. Want FEL, 54"fine cut mulching blade MMM, grill guard, ballast box. Turfs on 1860, R4's on 2360. Can you run the larger 2360 tires on the 1860? Do I need the extra 5HP? Is 18hp...

Found a dealer that was willing to negotiate and gave me what I needed for my BX2230 trade in, so pulled the trigger on a brand new unit! I'm getting a BX1860 with FEL and four-way valve, a 48"...

Ok im about to purchase a bx1860 in a month or so and I really like everything about it but the tire sizes. I really wish is had the bigger tires on it like all the other bx models, what I don't...

fellows would any of our dealers who contribute to this forum like to speculate on when we might see the first BX1860's and BX2360's, this fall or next year? thanks, shrekbelly

I know the new BX1850/BX2350/BX24 are just getting to dealers but I was just curious as to what the speculation was about the evolution of Glide Steer... I'm assuming it cost Kubota bit of $$$ to...