advise please: difficult workshop build

   / advise please: difficult workshop build
  • Thread Starter
#21  
I think it would be too much to use the loader. I would definitely go with the buggy at least at this point. I'm not sure how much good help I can get.....
 
   / advise please: difficult workshop build
  • Thread Starter
#22  
concrete alone is $627. I'll get someone to come and look at it to see about pumping etc
 
   / advise please: difficult workshop build #23  
Just a thought, you might see what it would cost to contract this out. See how the cost compares to pumping cost.
 
   / advise please: difficult workshop build #24  
the drives are narrow intended for my tractor and gear, not full driveways

How narrow? I drive a pump truck which is about the same size as most concrete trucks and you'd be amazed at some of the places it will fit into.
 
   / advise please: difficult workshop build #25  
How narrow? I drive a pump truck which is about the same size as most concrete trucks and you'd be amazed at some of the places it will fit into.

If you have 10 feet of clear width and 14 ft of vertical, they can get in.

If you buggy or use the loader, you might have to pay a stand bye fee; about $100/hour after the first hour. This really depends on the company, and how busy they are. Yours is a half load, and they surely don't want a truck and driver tied up for half a day.

a lot of front discharge trucks are 6x6, and can get places you won't think. Might be worth it to clear a way in, rather then pump.
 
   / advise please: difficult workshop build #26  
concrete alone is $627. I'll get someone to come and look at it to see about pumping etc

Is that including small load fee, environmental fee, trip charge, ect? Some companies charge extra for anything less than 8 cy; some for less than 5 cy.

Edit: the typical 3-4" pump doesn't handle standard concrete well; you need to order "pump mix" which uses smaller rocks. Same psi, can be same slump (pumps better at 5 or 6" slump though), but costs about $2.50/yard more last I knew. It's easier to work at times because your not fighting big rocks
 
   / advise please: difficult workshop build #27  
10' backing up, 9' is plenty if he can pull in. Also depends on the shoulder: is it clear? Hard enough to support the truck?

If you have 9-10'+ of useable width I'd get the ready mix company to come out and look to see if they can get back there.
 
   / advise please: difficult workshop build #28  
For sure check with concrete company on clearances. Those trucks can go lots of places, even on soft ground, if width and height is OK.
 
   / advise please: difficult workshop build
  • Thread Starter
#29  
the drives are gravel over 10' geotextile, but they curve a lot so the width is 9' at best, in between the trees. There's an area that sounds like a truck could get closer, but it'll probably make a mess of it-I just leveled and planted grass there. It would still be 40' away though.
 
   / advise please: difficult workshop build #30  
How far is the closest Ready-Mix plant? They may send a guy out to check it out if it's a slow day...
 

Tractor & Equipment Auctions

2015 John Deere 5085M (A50120)
2015 John Deere...
2014 Yale 3 stage 8500lbs lift solid tire forklift (A52748)
2014 Yale 3 stage...
(30) 24-A Macro Bins (A50121)
(30) 24-A Macro...
2006 Imperial 14Ft Flatbed T/A Equipment Trailer (A50323)
2006 Imperial 14Ft...
New Idea 483 Round Baler (A50774)
New Idea 483 Round...
2012 UNVERFERTH 10-INCH FRONT WHEEL SPACER FOR 10 BOLT HUB (A52748)
2012 UNVERFERTH...
 
Top