Search results

Anyone with a TX1510 could you possibly take a photo of the thermostat housing area on your K3B engine and post it....If I look at K3B manuals many of them show a thermostat and a fitting assembly (see image No 22) mine has neither!!!

ok the replacement pump comes with 2 gaskets and a steel plate which covers the impeller (the fan like thing that circulates the coolant) however if it is assembled with the plate in place it doesn't line up with the alternator and crankshaft pulley that drives the water pump; if I take the...

Hi Folks there's a braided hose which goes from the bottom of the radiator on my TX1510 seems to go into the engine blcok at the other end can anyone enlighten me as to its purpose.....and a part number as its very worn....

Hi folks the replacement water pump for my TX1510 (K3B Mitsubishi Engine)has a small outlet pipe (see picture bottom right) whereas the existing one does not(its got a 'plug' screwed into the opening - does anyone know whether this needs blanking off or attaching to something?

Hi folks when I shut down the engine there's coolant dripping onto the floor; its not from the thermostat housing nor the overflow pipe...seems to be lower down and doesn't do it whilst the engine is running....any ideas welcomed.... I know that it could be expensive LOL

Hi Folks what sort of weight will my TX1510 tow? May need to haul water in an IBC Tank from our Burn (stream) due to reduced spring supply in this hot weather and want to be safe.....

My TX1510 like many others does not have a fuel gauge fitted as standard..has anyone done anything to solve this 'problem' I guess just continually checking the level is the obvious answer but its still a pain having to bleed the fuel lines when you run out down the field even more so when...

Hi folks as a general rule should the top link be longer or shorter to achieve greater plowing depth? many thanks

Should there be a washer of some kind on the Oil drain plug folks? Seems to be slightly leaking but maybe just not tight enough....

Need to source a replacement hydraulic hose and wondering if anyone in the UK/Europe has had to do so and where you obtained it from also does anyone know precisely what size the thread is on the hose fittings?

Hi folks Friend has recently purchased an Iseki TK532 and wants to get a topper. Tractor data says Independent rear PTO does that mean an Overrun clutch is needed/recommended or not please?

Learned people I have a hydraulic fluid leak from one of the pipes on the 'joystick' on the Bulldog Loader on my Iseki TX1510 - Please see picture I haven't tried anything yet but should I try tightening the nut? or is there an O ring or other seal inside that may have failed? Advice...

Learned tractor owners I Have an Iseki TX1510. The Oil pressure light has started to come on very quickly when I throttle off completely (ie stop the engine) but also at very low revs. Someone suggested i purchase a pressure test kit as a first step which I have Can anyone suggest where this...

Any UK members recommend a source for an Oil Pressure Gauge (for TX1510) light is coming on very quickly when shutting down and occasionally coming on when at low revs

Hi Folks anyone with a TX1510 or similar fitted any additional working lights facing either to front or rear maybe on rollover bar....how did you wire them up?

Learned people the Oil Pressure Warning Light on my TX1510 has started coming on at low revs just recently what would be your possible diagnosis......please not expensive!!!

Hi folks anyone in the UK/Europe especially had to obtain a new filler cap washer and if so from where did you get it?

I have an Iseki TX1510 which as you will know has no included rear hydraulics. It has a front end loader installed with joystick control etc How would I go about adding some rear hydraulics? I would ideally like to run a log splitter and possibly a post driver or would it be simpler to buy a...

Hi folks does anyone use wheel spacers on their Iseki. I have a TX1510 and the wheels are too close together for our veg growing beds which are 30" If so where did you source them or did you make them yourself?

I have an Iseki TX1510 recently been difficult to start and battery drains very quickly. Done the usual checks on the battery with a multimeter with engine not running and then running 1/2 throttle and it would appear at least that it is being charged by the alternator as the meter shows an...

My TX1510 has a Delkor (Australian brand I believe) NS60MF Calcium 12v 45Amp battery in it. Its now failing to hold charge and I'm wondering if anyone has had to replace theirs particularly if you are in the UK could you tell me where you obtained a new one.....I have Googled extensively...

Anyone out there bought/made wheel spacers for an Iseki or Bolens; would like to increase my track front and rear to 30" which is the width of our veg growing beds

Drove down our field used the front end loader to do a little work; noticed the 3PH was right down so moved the lever to raise it - didn't move at all. Drove back to workshop by which time the 3PH was right up any ideas as to why folks please? Many thanks in anticipation

Hi everyone anyone out there with an Iseki or Bolens ever replaced the Hydraulic suction filter and o rings? Is it straightforward and any tips would be greatly appreciated

Anyone have an email address for Kingkutter I have tried submitting a question via their website twice now but had no response at all Needing some replacement tines but am in the UK

Hello all I bought this (Rotavator) Tiller with my Iseki TX1510. Can anyone give me a 100% definitive answer as to who the manufacturer was/is as I was told that it was imported from the good old USA and I now need some replacement tines I think someone previously suggested it was a KingKutter...

Can anyone tell me how much the Kingkutter 4 foot rotary tiller weighs please?

When I depress the clutch pedal going forwards and come to a halt on my Iseki TX1510 there is a **** of a screeching noise which appears to come from the rear left hand (as you sit on the tractor) wheel Anyone any ideas please?

Any advice welcomed - when using the FEL (Bulldog 282) attached to my Iseki TX1510 but only when tipping and raising the bucket there's what only can be described as a booming noise anyone any ideas please?

Anyone tell me what size the front nuts are please and where I can order from even in US if needs be

I know very little about Hydraulics but I have seen an advert for a Post Driver/Knocker which says 'Only requires 1 hydraulic spool connection'. I have an Iseki TX1510 only hydraulics are for 3PH and Bulldog Loader Would it be possible to add something which would enable me to use this post...

Anyone owning an Iseki in the UK particularly TX 1500/1510 what oil are you using for the hydraulics?

Anyone have an idea what a Bulldog 282 Front End Loader weighs please (approximately)

Any of you guys in the USA any experience of owning and using Budget Clamp On Tractor Bucket Forks Pallet by Paynesforks ? As usual impossible to get anything like this in the UK so may import. Seem really cheap but I am not going to be lifting anything really heavy (my loader states 200kg...

anyone got a parts list they can post for a TX1510 or if they are definitely the same for any other Iseki/Bolens model TX1500 etc that would be great

I have an Iseki TX1510. On a number of occasions over the past 12 months when it hasn't been used for a while the clutch won't disengage. Normally just by leaving it to warm up for a while this seems to free things up. However yesterday the same thing happened. I have trawled the forums here...

Anyone know what the Clutch Safety Switch actually does on the Isekis and could a faulty one cause problems disengaging the clutch? many thanks

Anyone tell me what size the grease points/nipples are on a Bulldog 282 FEL?

the operators manual says the 3PH is a JIS -0 (which I assume to mean Cat 0); the measurements suggest Cat 1 can someone confirm which is correct as I'm looking to buy EZ Hitch and obviously need to correct size many thanks

Any Uk forum members know anywhere in the uk where you can actually buy parts to build your own implements such as are sold in the USA by the likes of Woodward Crossings etc. I mean things like Bedder/Hiller Discs and Shanks, furrowers and so on ?

Can anybody tell me what the maximum lifting weight on the 3PH would be and also what the maximum towing weight would be assuming an A Frame with towball or drawbar with towball many thanks

I've been reading countless threads about ballast boxes etc. I have an Iseki TX1510 with a Bulldog 282 FEL. Normally I have a fairly heavy Rotavator on the back end which seems to work fine as a counterbalance. However there are a few tight places where something more compact would be useful...

This will probably bring a wry smile to many faces perhaps but I have now had my Iseki for 6 months and looking at the rear wheeels again yesterday it suddenly made me wonder why the tyre valves were on the 'inside'. Having looked round the web at Iseki images I'm wondering now whether the...

This will probably bring a wry smile to many faces perhaps but I have now had my Iseki for 6 months and looking at the rear wheeels again yesterday it suddenly made me wonder why the tyre valves were on the 'inside'. Having looked round the web at Iseki images I'm wondering now whether the...

Can someone tell me very simply when Diff Lock should be used Thanks

Appreciating that Tractor by Net is US 'orientated' are there any UK members who can recommend Compact Tractor Attachment companies (retailer or manufacturer) in the UK. UK prices seem to be much higher (whats new??) Looking for some sort of Rake for collecting stones at reasonable cost

basic question folks - what factors will affect the height my Iseki TX1510 will lift my Rotavator off the ground ? Looking at various Youtube videos the rotavators all seem to be much higher off the ground than mine I have tried changing the 'length' of the existing centre part of the hitch -...

As a very cautious newbie seeking more advice on PTO's etc. I have an Iseki TX1510 (Non Live PTO) and currently just a Rotavator which thanks to forum member is identified as a 4' King Kutter 2 Rotary Tiller (albeit perhaps branded under another name)The tiller manual states that all tractors...

Just bought an Iseki TX1510 and reading User manuals etc etc. Some people are recommending that we get a PTO overrrun clutch/free wheel extension as we will predominantly be using a rotavator attachment does anyone have any experience/thoughts on this please ?