Search results

What’s involved to replace a foggy hydraulic sight glass on 2014 t650?

Can/how could I run a front mount brush cutter on my 3038h. I have a WR LONG 3rd function set up on it now to operate a grapple. Only 3/8 hoses though. No rear remotes.

Any way to spin pto shaft to ease hooking up pto shaft equipment? Tried motor off, neutral no go

Has high flow only. How to make it use a low flow brush cutter?

Followed suggestion in previous post and ordered D starter handle and received this am. Replaced cord and was oh so careful about not letting starter spring unwind. Ran new cord up thru D handle and knotted. Second pull and knot pulled thru new handle. Fortunately did not unwind spring...

Had this saw for a very long time. Always a bear to get started the first time. Compression makes it almost impossible for the old guy to get more than a click on each pull. Does not have a compression release. Plug out it spins very easy. How can I reduce some compression to get it to spin...

After warm up engine will run “away” if you do not use any controls. If you keep something moving then ok. Looked at a bunch of YouTube about governor but can’t find my particular motor. Extremely difficult to get at. What to look for if I get the inspection plate off?

Had the jerky lift problem for some time. Utube showed problem. Replaced crumbled seal in piston in sleeve under seat. Worked lift arms a bit to get rod properly seated in back/bottom of piston and bolted back up ok. Hydro fluid full. Flow control valve in middle position. Lift won’t lift...

Ran perfect last time. Now, starts first pull and will idle forever. BUT as soon as I pull the trigger it dies. Restarts first pull, idle but can’t pull trigger. Ideas?

Cranks and runs fine until…you stop using any controls (throttle at 1600rpm) and the engine “runs away”. As soon as you operate any control it idles back down to operating rpm. As long as something is moving all is good. Something about the governor? Or what else?

Just did the 300 hr filters change. 3038H. Q on fuel filter. Book says remove drain on bottom, ok easy. Also says remove 2 wires from bottom. HOW, they seem to be moulded into the white plastic plug. ENDED UP USING CHANNEL LOCKS ANd just unscrewed plug but wires were pretty twisted up...

First alternator lasted 35 years, second 2 years. Dash now shows red light(alt) when cranked. On this unit when running, it will still run with key turned off(alt light off). So, is it ok to run with key in off position, guess it not charging, but doesn’t take much to crank. Shut fuel lever...

Ford 1920 shuttle shift. Glow plugs will not turn off so disconnected, another problem. The problem for a long time is starts fine, BUT if I stall it or shut it off, it will ONLY restart after about an hour cooldown.

Any source for a color coded wiring diagram for subject tractor. I have one, but not color.

Sort of a long post, awhile back posted about not starting after shutting off and trying to restart, would not till cooled down. Please hold this thought. Fooling around with it yesterday would not turn over, battery at 11.25v. Battery has been disconnected. Re connect battery, With the key...

Tractor starts fine on initial start up. However if it stalls or you just shut it off, it will not restart for at least 2 hrs until complete cool down. Just been careful in the past not to shut down, but need to get to problem. Ideas?

Posted earlier about the cheap adjustable top link that came with my 3038. Just got back from TS with a new one. Difference is like night and day and only $22. Old one the "eyes" we're welded on a 3/4" screw rod.(not very well!). New one has the eyes cast into the screw rod and is 1 1/8"...

3038 with 85 hrs. The adjustable top link eye broke in the middle of my creek carrying a 950 lb ballast weight. Was firmly attached to my Howse pallet forks. Looks like the weld just gave up. I do see a good bit of rust under the weld, so must have hada crack at some point. Point being that...

Cutting grass today with finish mower and way to heavy grapple on the front. Going down steep hill next to house and tractor started to slide. Was in two wheel drive. Grass not wet. Stood on the brake and would not stop. Right wheel going forward, left going backward! Yanked throttle back...

Is there a way to get the PTO shaft to freely move when hooking up. Having a hard time lining up the splines. Having to use a crow bar in the yoke to turn the blades on the cutter to try to line up is hard on everything, especially me.

Went out an cranked the tractor with the grapple already attached. kept in pole barn with big pile of firewood all around. While warming it up saw a hose that looked out of place on the right side. 5 ft black snake draped around the right cylinder thumb. Backed tractor out of barn, snake...

Last week posted about difficulty in reattaching my grapple due to excessive pressure in the connectors. Many responded, thanks, but have now come up with a sure fire way to relieve pressure without a hammer or other excessive measures. At the Lowes store they are doing away with Bessy(the...

First time after initial install hooking up grappler. The only way I could get the couplers to latch was loosen the hose at the cylinder to relive the pressure and losing a cup of hdy fluid. When I unhooked the two lids were closed down. So how do I leave the lids so that it will be easier...

Searched but could'nt find the photos where someone had made individual frames w/expanded metal to fit between each of the upright shanks of his grapple. Thinking about needing to do this myself, and at this point a few more pounds isn't going to hurt. Thought it might be in the ATTACHMENT...

Thought someone was going to post in the filter sticky what brand(s) of fluid were ok for the LS HST models.

Hit 50 hrs. Today playing with grapple. How many here use other than LS branded filters?

Hooked up the new grapple to the LS 3038H, and got scared real quick. 60" grapple at 650 lbs was probably to big, tried to lift a wet log 8'x22" and rear end went up like a rocket. Loaded tires and a box blade on the rear. Knew the load was heavy but wanted to see what it could do. So found a...

What do you really lose(or gain) by reducing from 1/2" to 3/8" or the other way, going from 3/8" to 1/2"? My new grapple has 1/2" plumbing but I'm running 3/8" from my 3rd function. I'm planning on using a 3/8 male to a 1/2 female thru a ISO 7241B coupler.

Will a AG series((ISO 5675)round ball nipple) QC, mate to a 600 series ((ISO 7241) cone shaped nipple) QC? Naturally same size.

Got the kit from WR Long. To me, they had the most ergonomical replacement grip with a rocker switch that I wanted. Also their mounting bracket was specific to my loader and not some put it where you can find a place for it. Got one miss matched coupling that was quickly replaced by Nelson...

My LS LL3104 loader uses a WALVOIL valve. Trying to do some research on the valve and the only ID I can find moulded into the valve body is 5 ( or maybe an S)/2P 1. Tons of valves on the WALVOIL web site, but nothing that seems to match these #'s. Can anyone point me in the right direction?

Been talking to several knowledge folks on the phone and in person and even LS in NC about the power beyond and getting about as many different answers. First my operator manual clearly shows on the hydraulic connections only one hyd hose going into the top of the FEL control valve, BUT I have...

Went to Tractor Supply today for a little shopping. My 3038H book specifies "API GL4 ISO VG 46/68" for Hydro oil. However when I picked up a bucket of the Traveller "ISO 46" fluid it said upon other things "NOT recommended for wet brakes"??? Did'nt get any yet, but am confused by the book...

Been studying the placement layout for the electric solenoid and block on subject tractor. In looking at lots of threads and utube vids, just can't find a suitable location for these parts that equate to about the size of two bricks with all the wires and hoses attached. About the only place...

Asked this in another forum, but no answers. In the diagram for my LS loader there is a P hose, C.O hose and a T hose. What are the abbreviations?

In the parts diagram for the hydraulic connections, there is reference to a P hose, C.O hose, and a T hose. Think I know, but to what do these refer?

Turned my wrongly installed stabilizer arm ( previous post ) and was looking at the pins that secure it to the frame. Recalling a previous post about the round pins snagging when the arms are raised, mine showed the same condition. The square portion of the pin that has the wire loop was badly...

This is the way the sway arms came. Looks like the right side male slide is mounted upside down? Wha

A Howse 3 point fork lift came with the used tractor I recently bought. It is a model SXFLPF. The tractor has a quick release bucket (LS 3104). What I would like to do is have it mounted on the FEL. I have been looking at a number of references for these forks but don't see how I can convert...

Thinking about the current deal on Pat's end links. Just measured 7 pieces of my equipment and the width of the end link connections vary from 24" to 31". So my question is how do you set the width on your end links with such a variance of the width of your equipment before you back up and...

Got about 3 hrs bushhog'n and this seat has to be improved. I'm about 230lb and compress those puny springs pretty much to the bottom. Talked to the dealer and he suggested his replacements were pretty$$$ and to look at TSC or northern Hyd. Can 't really find anything that will fit without...

Can anyone tell me exactly how many gallons of liquid the 20" rear tires on a 3038h will hold. I only need to get protection down to about 20 degrees where I'm located so not a lot of antifreeze will need to be added. Thanks.