Search results

Cooler but no filter…well that know of:-)

45 hours on it now. I just welded two 3x4x1/4 box vertical to the each side. I made them permanent. I could have drilled them and bolted them to the side flanges…easier to just stick them on… Can’t imagine needing them off at my place. Wide open around here…just steeper than a cows face...

I picked up a ground hog for planting 6’ to 20’ trees, etc. I was incredibly skeptical but have been pleasantly surprised! Planted nearly 40 trees and dug about a mile of hiking trails through my property (very steep land) as well as built rock walls with this little toy digger! Amazing work...

Thanks!

Are the remotes rated for continuous duty? Thinking of running an hydraulic brush mower off the FEL. There is a version that will fun off my 7.6 gallon per minute supposedly…. Thanks

Thanks everyone

Thanks! So no adverse problems by using spacers…increased load on bearings, etc….? My rims are already out as far as they will go…

I have a T474 tractor and am mowing 10-15 degree hillsides. It seems to be ok, but a little more stability would be less stressful! Would wheel spacers on the rear tires make much difference in stability? I’m thinking 4” spacers… Will the spacers cause any problems? What brand to buy? Rear...

Perfect! I wiggled the wire harness behind the parking brake lever and the problem went away! I’ll take the dash off when I do the 500 hour service and repair it then. Assuming that is the problem…hard to see in there with the dash on….

I could not see any but I’m not 60 anymore either!

Cool. Thanks. Are there any grounds under the dash?

Thanks! I will check it out!

Seat has a safety switch?? I generally start the tractor and warm up the tractor out of gear, brakes on, but I’m not in the seat…

Tractor Gaga’s 430 hours on it. All of a sudden it doesn’t want to send power to the starter unless you jump up and down on the brake pedal or reach in behind the steering column and wiggle wire harness. Fuel pump and everything else turns on with the switch…just won’t spin the starter without...

They were less than $600

Agreed! I’ll need to shorten them up to fit properly. I just slapped them on to be sure they were big enough before too much time passed. Don’t really need them now so I’ll spend time when it’s warmer to adjust them up correctly. Hope I don’t need tensioners. Looks like yours work great!

I purchased new chains for my TYM T474. Seem to be good quality, fit my tractor, and clears everything. still need to pick up some tensioners though. I was nervous about chains clearing the wiring in the first picture which is why I bought this style: 1.0x 43/16.00x20 Aquiline Multi-Purpose...

I’m actually not sure about that! I can not see anything but the top link hit the coupling sleeve and disconnected the hydraulic hose. Wish it was a bit further away from the top link!

I installed new o rings and it still leaked. Put in one of those washers with an o ring inside it and it sealed up. Had to use both though. O ring and the o ring with a washer. dealer suggested that using the loader hydraulics at the same time as the remote will cause it to burp those o...

Thank you! It’s a new tractor…well, a year old now with 250 hours. It just started leaking and I noticed the o ring had burped out. I put a new o ring in and it still burped out a bit. I’ll go to the hydraulic hose store near me and get them to size it for me. thanks folks!

My 474 hydraulic remote above the PTO is leaking oil. The o ring connection leaks because the o ring does not stay in the seat when tightening it down. is the o ring bad? Is there a better style available?

Thank you! That is A very helpful download.

I’m not finding a service manual so would sure appreciate a link...

Thank you!

My automatic throttle quit working with the pedals. The mechanical throttle works great. it’s out in the woods so I hate to haul it into the dealer who said, “I have heard of that happening, check wire connections to see if a twig unhooked something.” so at this point I shall have to haul...

I picked up an agristore cylinder. I had to put the cylinder with the hose junction upside down at the implement end. Otherwise the junction box will snag on the remote couplings causing them to release the hoses. best money I ever spent! Soooo much easier to change the box blade angles and...

I assume these a valve type connectors.... correct?

TYM 474. Do not want to tear up the front end....

My tractor has buttons on the loader joystick. In see they are to control a third hydraulic function. So, if I want to use those buttons to run a grapple, what do I need to activate those buttons? I also figure I need another hydraulic source. Where and how do I plumb that in? (I using the...

On another post I learned that I can buy any hydraulic top link and it would work on the TYM 474. But I felt like I was hijacking the post, so I started a new thread here. My question is about the hydraulic control. It appears to snap into 3 different settings, not like the 3 point hitch...