branson 3510i

I just purchased a Branson 3510i tractor and am looking for an operators manual. All I can find is the repair manual.

I was using my 3510i about 2 hrs ago, and it suddenly quit, like I had turned the switch off. Now it will turn over, but won’t run. I replaced the fuel filter (it was time anyway), bled the air out, and it still won’t run. I also cracked two different injector lines to see if there was an air...

My 3510i starter won’t turn over. I have a good battery, solid 12 volts to the starter, and also 12 volts to the wire directly below the main cable on the starter when the ignition switch is in the crank position. I want to take the starter off to bench test it, but I’m (seriously!) afraid I...

The steering cylinder on my Branson 350i is leaking (pouring) on the right hand (from the seat) end, and I’m about to replace the seals. I haven’t gotten the seal kit yet - $265+ for o-rings and seals - and I’m wondering if anyone has done this before? A replacement cylinder is $1,220+, which I...

'anyone have a list of replaceable hoses, lines, and wires for a Branson 3510i? Thanks!

My 05 or 06 3510i PTO won稚 engage. It worked OK yesterday, and simply won稚 engage today. I致e somehow lost the cover for the fuse panel (thatç—´ in another thread), so I checked all of the fuses. Theyæ±*e all good. My experience with solenoid coils is that they usually start giving trouble...

I have an 05 or 06 Branson 3510i and I致e lost the cover to the fuse panel. The inside of the cover indicated which fuse powered what, and I need that diagram. Can anyone direct me to where to find that diagram or maybe take a picture of theirs and post it? Thanks!

I own a Branson 3510i. Bought it new. While doing the transaction the dealer and I were talking about various thing and when I mentioned I lived at 9000 Ft., he said that he would install/adjust/modify don't remember his exact words, the tractor so that it would run better at my elevation. From...

My 3510i starter works fine when my Tractor is cool, but after it heats up it acts like the clutch/starter safety switch is almost but not quite engaged. The starter seems to kind of sputter. It might start, and it might not. Any thoughts/solutions?

I have a 3510i. Bought it new almost 11 yrs ago. It's been my self employment ever since. This is the third time it's stopped on me. Very frustrating the first time.. So now I know to open the hood and remove the left engine cover and wiggle this plug. Well now it's not even making connection...

Gents, Been bouncing around the forums trying to price check and find a good deal on a tractor. Here's what I have for ya'll: Branson 3510i 4x4 215 hours FEL Quick Attach Front Spear Front Hay Fork Howse 5ft Cutter Shuttle Shift That's all I know. I understand it's difficult, but I'm just...

This Branson 3510i used to run as expected, even at an idle the temp gauge went up into the normal range after a few minutes and stayed there. Starting a month ago, for no apparent reason, it stays cold, occasionally see it go to normal but then pretty much immediately heads back down...

I own a 3510i Branson Tractor looking for a oil filter from Napa can anyone help with this?

I have a 3510i that has developed a hydraulic problem. The whole system has weakened drastically over the last few hours of use. Right now if it's not at least at 2200 rpm, it will not raise the empty loader bucket. The backhoe (Branson 7620) moves very slowly and again not at all at low rpm. I...

I am looking at a Branson 3510i with FEL are there problems or issues with this model or brand?

Have been having problems with a Branson 3510 PTO that has baffled several highly experienced tractor users. The Tractor is 9 years old and have had it since day 1. Recently, the PTO started shutting off while mowing and after replacing the fuse seemed to work. Then it shut down again while...

Unfortunately, I busted up the grill on my Branson 3510, and Branson wants an obscene price to replace it. Does any one know of a "Branson Graveyard" or perhaps have a grill to fit mine? I can probably Frankenstein mine back together, buy it'll look like crap and my not be too strong. Help!

Looking for reason power steering tank split. Could it be from return line pressure line being to high? Maybe just the molded plastic tank was made of wrong gread of plastic?

I have a 3510i that leaks fuel from the fuel cap when on a slope. The cap will not tighten enough to prevent the leak. I have read some older posts that discuss the same problem, but no good solutions. Are there any replacement gaskets/ fuel caps or simple fixes for this proplem?

Dear TBN gurus, I'm back again with a few more questions that I can't find answers to by searching. I recently purchased a 3510i from a bank repo auction. It has ~150 hours on it and I don't think any maintenance was ever done (I'm cracking the original paint on each drain bolt that I...

So I started up my farm as a real business entity and now that it's tax time I need to determine the Fair Market Value of my tractor since I converted it from personal use to 90% business use. I know I got a steal on it 'cause it needed some work done to get it running. It's a 2003 Branson...

I was driving my 2003 Branson 3510i one block down the road to my uncles in highest road gear and when I turned into the driveway there was a dip and immediately after the engine started to lose power and stopped and shutoff. It would crank and fire but then run down and shutoff. I topped off...

I haven't gotten a chance to see the DK yet. Was pretty close to pulling the trigger on the 3510i Branson. Then I called a local Kioti dealer I hadn't spoke with yet. DK35SE with loader - $17,600 2 rear remotes (standard??) 3510i with loader - $16,900 Comparing stats on paper the DK seems...

I just got a quote for a branson 3510i tractor with loader and it was 19,200 does that seem high to anyone else?

I have a 2007 3510i and from day one when engaging the clutch, it's made this chattering or grinding noise. At first I thought it was new, so it would take time for the clutch surfaces to smooth out, and the noise would eventually stop. This has not been the case. I have now 170 hrs on the...

I've got a simple operator question that seems to be baffling me. How do you engage the PTO? With the tractor running and the clutch depressed I pulled the PTO lever up to the 540 RPM setting and I hear loud grinding noises. Background: We bough the tractor used a year ago and the clutch...

Tractor moves very slow, the engine has lots of power, but it just does not go fast. Could it be the clutch? Has 86 hours. jose:confused:

Where can I find the MSRP on this tractor? I can't seem to track it down on the web. Tom

Does anyone make a snow plow for a branson 3510i? Anyone have one for sale? Any help would be appreciated! Thanks in advance.

My new branson has approximately 10 hours on it now and the hydraulic pump is leaking from what appears to be the pump body seals, not any of the low pressure (return) hoses associated with the pump. It has developed a big enough leak to drip a small amount of fluid on the garage floor. Is...

century-ML-842880-ML- Branson specific post

Hi - I'm new to the forum. Been lurking all morning and have found some great info. I have 10 acres which I purchased about 2 years ago and I have been renting equipment thus far. I'm sick of dropping $2k/year renting poorly maintained equipment and since I have lots of work to do this spring...

I have a new NAPA grease gun and when I grease my tractor the hose is really hard to get off of the grease nipples. I've never had issue like this before. Is there a trick to this?

I have had my Branson for a couple of weeks, very impressed. I have a couple of questions. 1. I only have the position control for the PTO. I believe the second slot is for the draft control. I did not get the lever for this, is it optional? Not sure if I would need it anyway. 2. How heavy...