injector

Ford NH 1920 with Shibaura N844 engine, has always started and run smoothly, but just recently began running a little rough, like one cylinder is occasionally missing. Hoped it was just bad fuel or moisture in the sediment bowl, so I cleaned the bowl and drained out the fuel tank, put Seafoam in...

Does anyone know the correct size rubber return line from the injectors back to the tank? Could just measure the old ones, but they are quite swollen and not sure I'd get the right size. Thanks.

I'm hoping someone can help me with this. I took injectors apart and I'm not sure about reassembly. I didn't pay close enough attention when I took them apart. The nozzle body has a race groove and the matching disc that mates to it also has a race on one side and smooth on the other side...

Took apart injector as I saw a slight leak. Need gasket that goes between the halves of injector. Looks to be plastic. Not shown in parts breakdown. Included photos of injector with gasket on and off injector.

I removed the injectors on my 3510 , A1700 engine and found a lot of carbon buildup under 2 of them. Has anyone seen this before? What needs to be done, are they not sealing properly? Thoughts?

Looking for part number for a sd1840 injector or any info about buying replacements Thanks

Good afternoon, My Kioti is in need of some new injectors. I’ve been trying to wrap my head around the different part numbers to get the correct injector at a reasonable price. The Kioti part number on the current injector is F6805-53001. The Delphi part number is 28387256. When looking up...

Hello - I've read through many of the injector timing questions and answers but am finding my attempt at checking the timing confusing so I'm thinking I'm interpreting the instructions incorrectly. My process has been to remove the injector lines from the injectors, manually turn the engine...

Hello - new to this forum. I have a Yanmar 1700. It ran pretty well for 20 years, then stopped starting. Over the last few years I've slowly replaced many parts - injectors, injection pump, head (old one was leaking water into the cylinders), pistons, sleeves. With many attempts I can get the...

i need to replace gaskets on the back of the fuel injector pump. Is there a special tool that I need to use to remove it.

Have a Branson 4020R that the foot peal and levee for throttle dropped working. If you use the throttle control on the console the throttle lever on the pump seems to stick but still does not accelerate with the foot pedal or the throttle lever on the console. Any suggestions would be greatly...

Im tring to find a place to buy some parts this engine it’s a K3B I believe . I live in ontario canada . Any leads in which this engine was in so i can find a dealer and give them a part number would be great . Im missing a couple parts from within this pump. There is a spring a small what...

Looking A injector kit for my early model R1500 or a complete injector. Believe 1962

Hello, I have a Shibaura SD 1800 that has an injector pump that is bad. Where can I find a rebuild kit or replacement pump and the diagram for it? Thanks and God bless!

Hello. I have a 254 Chinese tractor with 3 cyl. LaiDong engine. The crank case keeps getting filled with diesel fuel somehow. I'm guessing the fuel is getting through from the injector pump maybe? Are there perhaps some kind of seals in the pump that I could change? Or a leaking gasket maybe? If...

The temperamental and very expensive Lucas pump ($3850 ) was unrebuildable so saw some guys we’re replacing with the old mechanical Bosch pump. I installed a new Bosch pump. Had the injectors recalibrated. Replaced the drive gear and rerouted the hard lines. Installed new lift ( supply ) pump...

Hello, Does anyone here recommend someone or a shop who can re-seal the injector pump on my 1998 Massey Ferguson 231? I’m aware I’d have to ship it. It is dripping diesel where the rotor head goes into the pump housing. There’s an o-ring there. I’d like the whole pump re-sealed since it has to...