joystick

Branson 3520R Tractor Loader JoyStick Repair Kit. 26001-0090 (DK35 40 45 50 55) This repair kit worked great for me. I know it says it fits a Kubota and other tractors but It did work on my Branson 3520R. It worked perfrct, a perfrct fit. I paid $32.00 on Amazon. 26001-0090 (DK35 40 45...

Has anyone had this issue? The Joystick for the hydraulics is stuck. I am interested to know whether this is a dealer service center only fix or perhaps a possible DIY solution. Thanks!

The joystick for my NH 250TL loader on my TC45DA has stopped lower the loader except when in the float position. What is a likely cause and how to rectify the issue? https://www.tractorbynet.com/forums/threads/tc45da-250tl.553336/

On my JD5200 I have problems with my loader. It is slow, goes down on its own, and tilts forward sometimes. I would like to replace the SCV, cables, and joystick with an aftermarket hydraulic control valve(joystick) to control the bucket. I would imagine I can route the supply/pressure line...

I have a CX2510. My joystick developed what is apparently a common problem. It would go into float but required a LOT of strength to pull it back out of float. The dealer came out and replaced the valve. He said it failed due to moisture/corrosion and that I should remove the cap...

I have a 2014 BX25D. When using my snow plow today the joystick got loose. It will lift and angle but wont let the plow drop. How do I remove the cover to see what came loose? Thanks

How do I remove the FEL joystick as the long arm is broken by the hyd valve

I have a Mahindra 1635 and the front/back joystick cable is sticking when returning to center from backwards... if that makes sense. When I pull the stick back towards me to raise the loader up, when I let go it does not return to center all the way and will continue raising on its own and will...

I have a Mahindra 1635 and the front/back joystick cable is sticking when returning to center from backwards... if that makes sense. When I pull the stick back towards me to raise the loader up, when I let go it does not return to center all the way and will continue raising on its own and will...

Hi All, I was using my tractor and the third function stopped working. Looked around and found a connection from the joystick to the valve (I am assuming thats where it goes) had seemingly ripped off. I'm perplexed as to how it happened. Anyone here know if this is a standard connector or if...

I bought a used 2018 GC 1720. I noticed the joystick seems a bit 'sloppy' compared to other tractors that I've used. The joystick runs thru a hole in the side of the tractor body with nothing supporting it but the rubber dust cover. I can't find a diagram to see if anything is missing. The...

I purchased a Ford 1910 4x4 in very good condition but the 770B loader valve is worn out. I plan to purchase a new single joystick 2 spool valve with float and power beyond, but I want to know if anyone out there has done this before. I would like to purchase this from Surplus Center, but I need...

2040 qt bush hog loader with a 25h439938control vale joystick rodends worn out looking for the right relacement

Hey so has anyone found an aftermarket repair for these joystick rods? My loader can't curl anymore and I see the rod and slider joint are worn. I can order through my dealer, but they are very far away. Amazon shows several kits as the three piece set, but they are 1/4" threads, so I'd have to...

With a 52 foot long hemlock log on the pto winch and the 3ph hitch in the up position, the loader doesn’t respond to power down. It will power up and drop when in float. When I drop the logs off the winch the loader operates normally. I calculated the log weight at about 3000 lbs total. I...

Hey all, Longtime lurker/new poster here. I have a new-to-me Ford 6610 Series 2 with a Great Bend 570 loader. It has, what I believe to be a Gresen 2702 hydraulic valve controlled remotely by a crude and very worn homemade joystick and cables. The joystick has a momentary push button on the...

I need some help. I was using the GC1710 at the cabin this weekend when the loader stick went loose. It still works to move the bucket around but it appears it is supported by the other end of the loader lockout pin, # 15 in the below picture. The problem is, my pin does not have threads on...

Hello, I was operating my tractor when the joystick all of a sudden became floppy. I took the it apart and inside the boot all the pieces came loose. Does anyone know where I can find a diagram in order to reassemble? Thank you.

All, I looked around to finger out how to change the boots on these (TN 55, 60, 65, 70, 75 cab models). All I learned is that others asked similar questions as well as a locking pin problem (locks the joy stick motion -- sliding collar on the joystick) but didn't list what they did or how they...

Is there an industry standard on how joysticks control the loader? In particular, when the joystick is moved to the left should the bucket curl or dump? Presently my bucket dumps when the joystick is moved to the left. The Summit manuals and documents are contradictory on this point. Some...

Based on my Googling and my local dealer, there does not appear to be an o-ring kit available for the FEL joystick directional control valve on a Mahindra 5500 Series. Nor am I able to find a parts diagram or catalog to identify and order the eight little o-rings. It would be reassuring to...

The first of this month I made a post in the hydraulic forum concerning the slow curl action on my RK37. It takes right at 17 seconds for a full curl when the manual states 5.3 seconds. Long story short I swapped the connections of the curl/dump hoses and the FEL lift arms at the valve and the...

Hi guys, I have a mahindra 3540 and my curl stoped working. I tried to get into the joystick assembly but I cant get to the ball joint to check the issue. Do I need to replace the whole joystick and cables?

Hi guys, I have a mahindra 3540 and my curl stoped working. I tried to get into the joystick assembly but I cant get to the ball joint to check the issue. Do I need to replace the whole joystick and cables?

So I just installed a WR Long 3rd function on my DK6010SE HST cab w/5521 loader. Now the damn joystick is frozen in place; will not move up, down, or to either side. I'm hoping the solution is something dumbly simple that I'm overlooking, and not done major malfunction in the loader valve...

The curl function on the joystick of my Branson 4225h is stuck. I'm not experienced at fixing stuff; can anyone comment on my reasoning before and suggest where to look next? (It's my week for breaking stuff...including the truck I could use to take the tractor to the dealer/mechanic, so it's up...

2021 Mihandra EMAX 20S with only 87 hours - the Joystick lever is already stripped and came out into my hand!!!! Has anyone else has this issue?

Hello all! Im new here... Im trying to find someone who can help me solve an issue with my Joystick Controller that controls the up & down on the 3 point arms. As you can see from the pics mine is worn out. Im confused as to how this controller even worked before because no hydralic lines...

Tym 330 HST - stock FEL controls / joystick. When I open the bucket and release it sticks open, does not spring back as it used to. Bucket keeps going to open - rolling back in toward tractor. Took off boot on joystick, everthing looks intact for the actual joystick, its just not...

There have been many posts about the broken part on the joystick of the MFGC1725 backhoe CB65. Lots of questions about parts, fixes, etc, and it seems that you have to scroll through pages of comments before you get any info on the actual parts. So hopefully, this post provides some of the...

I have a problem with my joystick in the cab. This loader stick has a ring that slides up and down as a locking device to lock out the loader. Somehow now the ding has to be just right not to low or locked not to high or there is so much slop you have to open the side door to dump the bucket. Is...

I recently broke one of the crappy original plastic pistons in my loader joystick and figured I could buy the parts and fix it myself. It didn't seem too complicated but there is one thing that seems to not add up. The replacement piston part (R230282) is structurally different than the...

I've owned a 4720 with cab for 15 years that I still have. A couple of years ago, I decided that I needed a second tractor that size and bought a new 4066R with cab. One thing that bothers me is that the lock lever for the joystick on the 4066R protrudes out from the right console a couple of...